WASSERSTEIN FLOODLIGHT User manual

Type
User manual

WASSERSTEIN FLOODLIGHT is a versatile mount designed to provide a secure and stable base for your Blink Floodlight camera. With its no-drill design, it can be effortlessly attached to various smooth surfaces, including tile, marble, metal, plastic, and wood. The mount ensures reliable adhesion, allowing you to position your camera at optimal viewing angles without damaging your walls. It also features a convenient release tab for easy removal of the floodlight when needed.

WASSERSTEIN FLOODLIGHT is a versatile mount designed to provide a secure and stable base for your Blink Floodlight camera. With its no-drill design, it can be effortlessly attached to various smooth surfaces, including tile, marble, metal, plastic, and wood. The mount ensures reliable adhesion, allowing you to position your camera at optimal viewing angles without damaging your walls. It also features a convenient release tab for easy removal of the floodlight when needed.

Floodlight
No-Drill Mount
USER MANUAL
In the Box
Applications
1 x no-drill mount
1 x extra sheet
of mounting tape
This mount sticks to most smooth surfaces,
such as tile, marble, metal, plastic, and wood.
page 1page 1
Warning!
Compatibility
Blink Floodlight Mount
• Read this manual and instructions carefully
before use. Failure to follow the safety
instructions may cause injury or damage to
your property.
Do not stick to brick, stucco, or wall paper.
Extreme weather condition can shorten the life
of the mounting tape and your camera,
beware when mounting it outdoor.
Do not hang the floodlight on the mount
immediately, wait for at least 24 hrs before
installing the floodlight.
It is not recommended to mount the floodlight
above a pathway or door where people will be
under.
The surface can be damaged when removing
the mount from the wall.
page 2
Installation
1. Check the view and test the trigger event
from the Blink app before installing.
2. Make sure the surface you want to apply the
mount to is smooth, dry, and clean.
3. Remove the protective film from the
mounting tape without touching the
adhesive.
Note: For best results, the tape should be
applied at a minimum temperature of 60°F
(15°C).
page 3
4. Carefully attach the mount to the surface in
one go. Press and hold for 30 seconds to
ensure maximum adhesion.
5. Wait for 24 hrs for the adhesive to fully dry.
6. Slide the floodlight onto the mount until it
clicks.
page 4
7. To remove the floodlight, press the tab on the
mount down and slide the floodlight to the
right.
1. To remove the mount, remove the floodlight
from the mount.
2. Slowly twist and pull the mount at the same
time. Gently lift it up to prevent damage to
the wall (use a hairdryer for easier removal).
3. Remove the tape by pulling it downwards.
Wipe off any leftover residue.
Removing The Mount
page 5
Contact Us
Made in China
www.wasserstein-home.com
Scan the QR code below or email us at
Blink Floodlight Mount and Camera
are not included.
Wasserstein is a trademark of Dropcases Ltd.
Wasserstein is not affiliated with
Immedia Semiconductor, LLC
Blink is the trademark of Immedia
Semiconductor, LLC
4. Make sure to remove all the old adhesive
before applying the new one.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

WASSERSTEIN FLOODLIGHT User manual

Type
User manual

WASSERSTEIN FLOODLIGHT is a versatile mount designed to provide a secure and stable base for your Blink Floodlight camera. With its no-drill design, it can be effortlessly attached to various smooth surfaces, including tile, marble, metal, plastic, and wood. The mount ensures reliable adhesion, allowing you to position your camera at optimal viewing angles without damaging your walls. It also features a convenient release tab for easy removal of the floodlight when needed.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI