V-ZUG 257 Installation guide

Type
Installation guide

V-ZUG 257 is a front loader washing machine designed for one-family households. It has a 1400 RPM spin speed and a 7 kg load capacity. The appliance features a variety of programs, including a 20-minute quick wash and a wool cycle. It also has a delay start function and a child lock. The V-ZUG 257 is energy-efficient and has a noise level of 72 dB during the wash cycle and 76 dB during the spin cycle.

V-ZUG 257 is a front loader washing machine designed for one-family households. It has a 1400 RPM spin speed and a 7 kg load capacity. The appliance features a variety of programs, including a 20-minute quick wash and a wool cycle. It also has a delay start function and a child lock. The V-ZUG 257 is energy-efficient and has a noise level of 72 dB during the wash cycle and 76 dB during the spin cycle.

Installation instructions
Washing machine «Front loader»
One-family household
J257.0531
14.1.08 ITH
1
These installation instructions apply only to the model: 257
The necessary installation material is located in the drum of the washing machine.
Open the appliance door
The appliance is not yet connected to the mains supply.
1. Open drain tank A by pressing on it.
2. Remove emergency release key B from its bracket.
3. Insert the key into the opening cap and pull it in the direction of the arrow.
Remove the transportation locks
1. Remove the 3 screws D with the red washers and sleeves
on the rear side of the appliance.
2. Close the keyholes with rubber plugs E.
The appliance should be installed by qualified personnel only. Each step must be carried out and
checked in full in the order specified.
Validity
Installation accessories included
Before operating for the first time
The transportation locks (C) have to be removed before the appliance is put into operation for
the first time.
A
B
1.
2.
3.
DE
C
Installation instructions
Washing machine «Front loader»
One-family household
J257.0531
14.1.08 ITH
2
1. Raise the appliance slightly at the front and pull it forward,
away from the installation plate.
2. Secure the installation plate to the location you wish to install the
appliance using 4 screws. On smooth and clean floors, you
can affix the installation plate with the enclosed double-sided
adhesive tape.
3. Dampen the mounting slots on the installation plate with water.
4. Position the appliance approximately on the rear adjuster feet
(spanner supplied).
5. To ensure smooth, fault-free operation, the appliance must be
perfectly vertical. Use a spirit level to position the appliance.
6. Slide the appliance into position and finely adjust the front
adjuster feet until the appliance is stable. The appliance must
not wobble.
Installation
Use the installation plate to install the appliance. This plate fixes the appliance in position (for
both freestanding appliances and appliances placed in a niche).
Freestanding position
1 This only applies if no plumbing fittings are to be installed
behind the appliance.
2 Depth including appliance door: min. 630 mm
Depth without appliance door: min. 600 mm
Positioning in a niche
Niche height min. 860 mm
min. 550
(1)
50
595
min. 15
Appliance front
Installation plate
50
Cut-out for lateral
connections, to the
left or right side
min. 100 × 100 mm
min. 600
Niche width
min. 630/600 (1, 2)
Niche depth
Furniture
front
Installation instructions
Washing machine «Front loader»
One-family household
J257.0531
14.1.08 ITH
3
Water inlet
Only cold water G¾", optimal working pressure 0.3 MPa (3 bar)
Possible pressure range: 0.1–0.6 MPa (1–6 bar)
The appliance must not be connected to a mixer tap or a continuous flow boiler!
A The tap seal seat must be clean and flat.
A Install the hose without bending or twisting it.
A Check the seal.
Water outlet
A When installing the drainage hose, protect it against damage and bending (hot suds will flow through it).
A Assemble the hose clip for all connection variants.
A If draining into the bath tub, sink etc. use the bend to fix the end of the hose.
A The drain pump can pump to a max. height of 1.2 m.
Plumbing in
Always observe the local water supply authority’s regulations.
Any old water supply and drain hoses must always be replaced with new hoses.
max. 700
min. 350
Hose clamp
Drainage hose
Rubber connector
Shorten drainage hose to
required length.
Cannot shorten drainage hose!
ø exterior 28.0 mm
ø interior 21.5 mm
Hose clip
(bend)
1.5 m
Installation instructions
Washing machine «Front loader»
One-family household
J257.0531
14.1.08 ITH
4
1. Empty the washing drum.
2. Operate as explained in the «Washing» section of the operating instructions.
3. Place a wet piece of washing, such as a large towel, in the washing drum.
4. Select the programme and wait for water to flow into the appliance.
5. Press the button repeatedly until appears on the plain text display.
6. Press the button repeatedly until appears on the plain text display.
7. Check water discharge and spinning.
8. During spinning, check that the appliance is firmly positioned. Readjust the adjuster feet until the device is stable.
Electrical connections
Electrical connections must be carried out by trained electricians in accordance with the regula
tions of NIN and the local electricity supply companies.
A mains isolating device with 3 mm contact opening should be provided in the house wiring sys
tem. Switches, plug and socket devices, circuit breakers and fusible cutouts which are accessi
ble after installation and which have allpoles switching are permissible as isolating devices.
Effective earthing and separately installed neutral and earth conductors (schematic diagram
TNS) ensure safe and faultfree operation. Old installations should always be checked.
Voltage Rated load Fuse protection Mains cable
400 V 2N~ 50 Hz 3500 W 10 A 1.8 m
230 V~ 50 Hz 2300 W 10 A 1.8 m
Function control / Operating for the first time
L2
L1
N
L1
N
10 A
10 A
Mains cable 3 × 1 mm
2
brown
blue
yellow/green
Mains
230 V~
Mains cable 4 × 1 mm
2
black
brown
blue
yellow/green
Mains
400 V 2N~
Spinning
Spinning at 400
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

V-ZUG 257 Installation guide

Type
Installation guide

V-ZUG 257 is a front loader washing machine designed for one-family households. It has a 1400 RPM spin speed and a 7 kg load capacity. The appliance features a variety of programs, including a 20-minute quick wash and a wool cycle. It also has a delay start function and a child lock. The V-ZUG 257 is energy-efficient and has a noise level of 72 dB during the wash cycle and 76 dB during the spin cycle.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI