The appliance should be installed by qualified personnel only.
Each step must be carried out and checked in full in the order specified.
Validity
The installation instructions apply to the model: TL WP (12001)
Transport
Transport the appliance in an upright position only! Transporting it in any other position will result in damage to the appli-
ance! When carried carefully without being shaken, the appliance may be tilted a maximum of 90° to the left (viewed from
the front).
The appliance must be allowed to stand in the standard operating position for about 2 hours before using the heat pump.
Failure to observe this can result in damage to the appliance.
Fron
t
Front
Front Back
Front,
upside down Side
Installation instructions
J12001.113-7
19.11.14
Heat pump dryer
One-family household
1
Identification plate
Open the appliance door.
– The identification plate 1 is located bottom right.
1
Supplied installation accessories
The necessary installation accessories are located in the washing drum.
Description Article no. Number See installation step
Condensate drain set W5.6298 1 4. Connect condensate drain
Installation plate (W4.0653)
Including double-sided adhesive tape S
Screw material contained in condensate drain set (W5.6298)
Tower installation
Tumble dryer model TL WP (12001) upon washing machine model L (11001), S (11002), SL (11003), SLQ WP (11004) or SLQ
(11006)
P
S
K
For tower installation, click in the six positioning cams P as shown in the diagram.
Take out the double-sided adhesive tape S and adhere to the mounting surfaces A.
Installation instructions
J12001.113-7
19.11.14
Heat pump dryer
One-family household
2
Turn installation plate 3. Push to the front edge of the washing machine cover plate (see arrow) and adhere into place.
3
Tumble dryer model TL WP (12001) upon washing machine model L (265), S (266), SL (268), or SLQ (269)
U
U
B
12 mm
6 mm
Mounts U for installing a new tumble dryer on an older V-ZUG washing machine. Cut the double-sided adhesive tape into two down
the centre. Cut out the mounts U. Adhere the double-sided tape to both sides of the mounts U. Adhere the mounts U to the mounting
surfaces B exactly as shown in the diagram. Push the installation plate to the front edge of the cover plate of the washing machine
and adhere into place.
Installation instructions
J12001.113-7
19.11.14
Heat pump dryer
One-family household
3
Room conditions/Ventilation
Keep all ventilation slits on the appliance clear and unobstructed. Otherwise an adequate supply of air is not guar-
anteed.
The room must be well ventilated to ensure that the room temperature does not exceed 35°C.
The room temperature should be kept as low as possible to ensure the economic running of the appliance. A room temperature of
over 35 °C is critical and lengthens the duration of the programmes.
If the volume of the room in which the appliance is located is at least 20m³ when closed:
Condensation may form on thermal bridges!
The room must be aired (by opening the door to or a window in the room) between consecutive drying programmes!
If the volume of the room in which the appliance is located is less than 20m³:
There must be air inlet and outlet openings (open window, ventilation grille or slits in the door, ventilation system) to the adjacent
room or to the outside.
Installation instructions
J12001.113-7
19.11.14
Heat pump dryer
One-family household
4
Installation
Work steps 1–5 must be carried out in full in the order specified.
1. Positioning the installation plate
Use the installation plate to install the appliance. It fixes the appliance in position, and is for use with both free-standing
appliances and appliances positioned in a niche.
The installation plates for the washing machine and tumble dryer are the same.
Raise the appliance slightly at the front and pull it forward, away from the installation plate.
At the site where the appliance is to be installed, fix the installation plate with 3 screws (using the screws supplied with the drain
hose set). If the floor is smooth and clean, the installation plate can be affixed using the double-sided adhesive tape Ksupplied.
Dampen the mounting slots on the installation plate with water.
Free-standing position
If a tumble dryer and a washing machine are positioned side by side, keep a distance of min. 5 mm between the installation
plates and to the walls.
In order to keep the distance to the wall, fold out the spacers D on the installation plate. This only applies if no plumbing fittings are to
be installed behind the washing machine.
577
≥ 28*
505
≥ 555*
50
595
≥ 5
≥ 5
D
K
* This only applies if no plumbing fittings are to be installed behind the appliance. Add another 20 mm if the condensed water hose
leads away to the left.
Positioning in a niche
If a tumble dryer is installed in a niche, a 130° door stop must be provided (article no. W5.4086).
If the niche is fitted with a door, ensure that this door remains open during the processing time. Niche doors and appliance
doors are advantageously fitted on the same side.
Centre the installation plate in the niche.
Installation instructions
J12001.113-7
19.11.14
Heat pump dryer
One-family household
5
A
≥ 600
B
Cut-out for lateral connections,
to the left or right side,
min. 100 × 100 mm
Niche height
min. 860 mm
Variant Positioning Niche depth A installation offset for
installation plate B
1
Door of washing machine protruding from niche front min. 605 mm 50 mm
2
Door of washing machine recessed behind niche front min. 635 mm 80 mm
Variant 1 Variant 2
B
A
Appliance door
Installation plate
Niche
B
A
Appliance door
Installation plate
Niche
min. 860
Niche height
400 cm²
Ventilation grille
The heat given off from the rear of the appliance must be conducted out of the niche. By means of 2 ventilation grilles P33.002 or a
ventilation cut-out of min. 400 cm
2
in the niche cover ensure there is a supply of fresh air via the connection opening.
The condensed water hose must not be crushed between the rear of the appliance and the building wall.
Installation instructions
J12001.113-7
19.11.14
Heat pump dryer
One-family household
6
Mount the installation plate on the washing machine using the double-sided adhesive strips supplied.
Take the tower panel 1 at the back of the tumble dryer out of the fixture 2. Install the tower panel 1 on the mounted installation
plate 3. Mount the tumble dryer.
1
3
2
1
The heat given off from the rear of the appliance must be conducted out of the niche.
Mount ventilation grille P33.002 and ensure there is a supply of fresh air via the connection opening.
Tower panel W5.5687
Niche set W5.4086
≥
50
≥1710
Niche height
400 cm²
Ventilation grille
≥ 860
Niche height
400 cm²
Ventilation grille
Installation instructions
J12001.113-7
19.11.14
Heat pump dryer
One-family household
7
2. Levelling
Roughly adjust the rear adjuster feet.
Appliance must stand level to ensure fault-free operation. Use a spirit level (L)
to level the appliance.
Slide the appliance in. Finely adjust the front adjuster feet until all 4 feet are
standing firmly on the floor.
– The appliance must not wobble!
L
3. Electrical connections
Electrical connections must be carried out by qualified personnel in accordance with the guidelines and standards for low-
voltage installations and the specifications of the local electricity supply companies.
A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. An
all-pole mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug
and socket devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles
switching are permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors
ensure safe and fault-free operation. After installation, live parts and cables with basic insulation must not be accessible.
Check old installations.
The appliance is designed for use up to a max. altitude of 2000 m above sea level.
Refer to the identification plate for information on the required mains voltage, current type and fuse protection.
Connection cable
Valid for all washing machines and tumble dryers in the Adora model range.
Do not cut off the plug.
Combi connection tumble dryer / washing machine (models 12001-12003, 11001-11006)
1
0
L1
L2
L3
N
10 A
Total connected load: max. 6900 W
Washing machine
Tumble dryer
Wall switch
Mains
400 V 3N~
brown
black
brown
blue
yellow/green
4 × 1 mm²
Mains cable
3 × 1 mm²
Mains cable
Error message «U1»
The appliance detects overvoltage. Check the wiring, especially the neutral conductor.
Installation instructions
J12001.113-7
19.11.14
Heat pump dryer
One-family household
8
4. Connect condensate drain
When installing the drain hose, protect it against damage and bending!
Fasten drain hose A to nozzle B using the hose clip.
B
A
Single connections
Maximum pumping height: 1.2 m
Drainage into fixed upright outflow pipe Connection to sink drain trap
Set W5.3070
≥ 350
≥ 800
• Cannot be connected to a double drain trap.
• There must be a separate concealed drain trap for each appliance.
Washer-dryer combinations
• Can be connected to a double drain trap.
Washer-dryer tower Installation side by side
with drainage into fixed upright outflow
pipe
with combi drainage set W5.5969 with combi drainage set W5.5969
≤ 700
≤ 700
≤ 700
Installation instructions
J12001.113-7
19.11.14
Heat pump dryer
One-family household
9
5. Using for the first time
When the appliance is connected to the power supply for the first time, it is possible to select a function test. The purpose of the
function test is to check the installation. It takes about 3 minutes. The function test can be selected immediately after installation, as
the heat pump is not started for the function test.
The function test cannot be aborted by interrupting the power supply.
Once the function test has been run or aborted, it can no longer be selected and the appliance enters the normal selection mode.
Starting the function test
Connect the appliance to the mains and wait for to appear in the digital display.
Use the button to start the function test.
The function test can be interrupted in 2 ways:
Open the appliance door.
– flashes in the digital display.
– After closing the appliance door, the indicator lights for the and buttons flash.
Or
Press the button.
– The indicator lights for the and buttons flash.
Continuing the function test:
Press the button.
– The remaining duration appears in the digital display, e.g.
Aborting the function test:
Pressing the button aborts the function test and all displays go out.
End of function test:
– All displays go out on completion of the function test.
The appliance can only be operated after standing in the normal operating position for around 2 hours. Failure to observe
this can result in damage to the appliance.
Installation instructions
J12001.113-7
19.11.14
Heat pump dryer
One-family household
10
/