WAGO 2-channel, 4 - 20 mA, Ex i User manual

Type
User manual
Pos: 2 /Dokumentation allgemein/Einband/Einband Handbuch - Fronts eite 20 15 - mit Doc Var iabl en ( Sta ndar d) @ 9\ mod_1285229289866_0.docx @ 64941 @ @ 1
WAGO-I/O-SYSTEM 750
Manual
750-586
2AO 4-
20mA Ex i
2-Channel Analog Output Module 4-
20 mA, Ex i
Version 1.2.0
HW-Version 05, SW-
Version 3A
Pos: 3 /A lle Ser ien ( All ge mein e M odul e)/ Rec htlic h es, A llg emei nes /Im pre ssu m f ür St and ard han dbüc her - al lg. Ang aben, A nschr iften, Telefo nnum mern un d E-Mail- Adres sen @ 3\mod_1219151118203_21.docx @ 21060 @ @ 1
2 WAGO-I/O-SYSTEM 750
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
© 2017 WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: +49 (0) 571/8 87 – 0
Fax: +49 (0) 571/8 87 – 1 69
Web: http://www.wago.com
Technical Support
Phone: +49 (0) 571/8 87 – 5 55
Fax: +49 (0) 571/8 87 – 85 55
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: documentation@wago.com
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.
=== Ende der Lis te f ür T e xtmar ke Ei nb and _vor ne = ==
WAGO-I/O-SYSTEM 750 Table of Contents 3
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
Pos: 5 /D ok ument ati on al lg em ein/V erz eic hni sse /Inh alts ver zei chni s - Ü bersc hrift oG und Ver zeich nis @ 3\mod_1219151230875_21.docx @ 21063 @ @ 1
Table of Contents
1 Notes about this Documentation ................................................................. 5
1.1 Validity of this Documentation ................................................................. 5
1.2 Copyright ................................................................................................... 5
1.3 Symbols ..................................................................................................... 6
1.4 Number Notation ....................................................................................... 8
1.5 Font Conventions ...................................................................................... 8
2 Important Notes ........................................................................................... 9
2.1 Legal Bases ............................................................................................... 9
2.1.1 Subject to Changes ............................................................................... 9
2.1.2 Personnel Qualifications ....................................................................... 9
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying
Provisions ............................................................................................. 9
2.1.4 Technical Condition of Specified Devices ......................................... 10
2.2 Safety Advice (Precautions) .................................................................... 11
3 Device Description ..................................................................................... 13
3.1 View ........................................................................................................ 14
3.2 Connectors ............................................................................................... 15
3.2.1 Data Contacts/Internal Bus ................................................................. 15
3.2.2 Power Jumper Contacts/Field Supply ................................................ 16
3.2.3 CAGE CLAMP
®
Connectors ............................................................. 17
3.3 Display Elements .................................................................................... 18
3.4 Operating Elements ................................................................................. 18
3.5 Schematic Diagram ................................................................................. 19
3.6 Technical Data ........................................................................................ 20
3.6.1 Device Data ........................................................................................ 20
3.6.2 Supply ................................................................................................. 20
3.6.3 Communication .................................................................................. 20
3.6.4 Outputs ............................................................................................... 20
3.6.5 Explosion Protection .......................................................................... 21
3.6.6 Connection Type ................................................................................ 21
3.6.7 Climatic Environmental Conditions ................................................... 22
3.7 Approvals ................................................................................................ 23
3.8 Standards and Guidelines ........................................................................ 25
4 Process Image ............................................................................................. 27
5 Mounting ..................................................................................................... 28
5.1 Mounting Sequence ................................................................................. 28
5.2 Inserting and Removing Devices ............................................................ 29
5.2.1 Inserting the I/O Module .................................................................... 29
5.2.2 Removing the I/O Module .................................................................. 30
6 Connect Devices ......................................................................................... 31
6.1 Connecting a Conductor to the CAGE CLAMP
®
................................... 31
6.2 Power Supply Concept ............................................................................ 32
6.2.1 Power Supply Concept in Marine Applications ................................. 34
6.3 Connection Example ............................................................................... 36
4 Table of Contents WAGO-I/O-SYSTEM 750
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
7 Use in Hazardous Environments .............................................................. 37
7.1 Marking Configuration Examples ........................................................... 38
7.1.1 Marking for Europe According to ATEX and IECEx ........................ 38
7.1.2 Marking for America (NEC) and Canada (CEC) ............................... 42
7.2 Installation Regulations ........................................................................... 45
7.2.1 Special Notes Regarding Explosion Protection .................................. 45
7.2.2 Special Notes Regarding ANSI/ISA Ex ............................................. 47
8 Appendix ..................................................................................................... 48
8.1 Rated Surge Voltage ............................................................................... 48
List of Figures ...................................................................................................... 49
List of Tables ........................................................................................................ 50
=== Ende der Lis te f ür T e xtmar ke V erz eic hnis _vor ne == =
WAGO-I/O-SYSTEM 750 Notes about this Documentation 5
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
Pos: 7 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten/ Ebe ne 1/Hi nwei s e zu dies er D o kume ntati on - Über schr ift 1 @ 4\mod_1237987661750_21.docx @ 29029 @ 1 @ 1
1 Notes about this Documentation
Pos: 8 /A lle Ser ien ( All ge mein e M odul e)/ Sic her heit s- und sonstige Hinweise/Hinweis/Hinweis: Dokumentation aufbewahren @ 4\mod_1237987339812_21.docx @ 29026 @ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation is
included, if necessary.
Pos: 9 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten/ Ebe ne 2/G ültig kei tsb ereic h - Über schr ift 2 @ 12\mod_1338912448776_21.docx @ 96469 @ 2 @ 1
1.1 Validity of this Documentation
Pos: 10 /S eri e 7 50 ( WA GO-I/ O-SYSTEM) /Hi n weise z ur Do kum ent ati on/G ülti gkei tsb erei ch/ Gült ig keit sber ei ch D oku men tati on I /O-Modul 750-xxxx, ohne Variantenangabe @ 14\mod_1358944037947_21.docx @ 109346 @ @ 1
This documentation is only applicable to the I/O module 750-586
(2AO 4-20mA Ex i).
Pos: 11 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/Hi nw eise /Ac htu ng: H in weis zur D oku ment ati on I/ O-M odule 75 0-xxxx @ 4\mod_1237986979656_21.docx @ 29023 @ @ 1
The I/O module 750-586 shall only be installed and operated according to the
instructions in this manual and in the manual for the used fieldbus
coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
Pos: 12.1 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Ur heb ersc hut z - Ü bersc hr ift 2 @ 23\ mod_1435647042188_21.docx @ 184808 @ 2 @ 1
1.2 Copyright
Pos: 12.2 /All e Seri en ( All ge meine Mo dul e)/R ec htlic hes , All ge mei nes /Urh eber sc hutz au sführ li ch @ 4\mod_1235565145234_21.docx @ 27691 @ @ 1
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos: 12.3 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1
6 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
Pos: 12.4 /All e Seri en ( All ge meine Mo dul e)/Ü bers chri ften/ Ebene 2/ Sym bole - Üb ers chri ft 2 @ 1 3\mod_1351068042408_21.docx @ 105270 @ 2 @ 1
1.3 Symbols
Pos: 12 .5.1 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und so nsti ge H in weis e/G efa hr/G efa hr: _War nu ng vor P ers on ensc hä den allg emei n_ - Erl äuter ung @ 13\ mod_1343309450020_21.docx @ 101029 @ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12 .5.2 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonstige Hin weise/ Gefahr /Gef ahr: _ Warnung vor Pers onen schä den dur ch ele ktrisc hen Stro m_ - Erläuterung @ 13\mod_1343309694914_21.docx @ 101030 @ @ 1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12 .5.3 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und so nsti ge H in weis e/W arn ung/ War nung : _ War nu ng vor P ers one nsch äde n al lg emei n_ - Erläuterung @ 13\mod_1343309877041_21.docx @ 101035 @ @ 1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos: 12 .5.4 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonsti ge Hin weise/ Vorsic ht/V orsic ht: _War nung vor Pers one nschäd en allg emein _ - Erläuterung @ 13\mod_1343310028762_21.docx @ 101038 @ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos: 12 .5.5 /Al le Seri en (Allgemeine Module)/Sicherheits- und sons tig e Hi n weis e/Ac htu ng/ Acht ung : _ Warnu ng vor Sac hsc häd en al lge mei n_ - Erläuterung @ 13\mod_1343310134623_21.docx @ 101041 @ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12 .5.6 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonsti ge Hin weise/ Achtu ng/A chtung : _War nung v or Sachsc häd en durc h elektr ostati sch e Aufla dung_ - Erläut erung @ 13\mod_1343310227702_21.docx @ 101044 @ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12 .5.7 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonstige Hinweise/Hinweis/Hinweis: _Wichtiger Hinweis allgemein_ - Erläuterung @ 13\mod_1343310326906_21.docx @ 101047 @ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos: 12.5 .8 /A ll e Ser ien ( Al lg emei ne M od ule)/ Sic her heit s- u nd s ons tig e Hi nwei se/I nf orma tio n/I nfor mat ion: _ Weiter e I nf orma tio n al lge mei n_ - Er läut erung @ 13\mod_1343310439814_21.docx @ 101051 @ @ 1
WAGO-I/O-SYSTEM 750 Notes about this Documentation 7
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos: 12.6 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1
8 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
Pos: 12.7 /All e Seri en ( All ge meine Mo dul e)/Ü bers chri ften/ Ebene 2/ Dars tellu ng der Za hlens yste me - Übers chr ift 2 @ 23\ mod_1435647128078_21.docx @ 184811 @ 2 @ 1
1.4 Number Notation
Pos: 12.8 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Za hlens ys te me @ 3\mod_1221059454015_21.docx @ 21711 @ @ 1
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated with
dots (.)
Pos: 12.9 /All e Seri en ( All ge meine Mo dul e)/Ü bers chri ften/ Ebene 2/ Schr iftk onventi one n - Übersc hri ft 2 @ 23\mod_1435647186005_21.docx @ 184814 @ 2 @ 1
1.5 Font Conventions
Pos: 12.1 0 / Alle Ser ie n (All ge mein e M odul e) /Re chtl ich es, Allg em ein es/Sc hr ift konv enti onen @ 3\mod_1221059521437_21.docx @ 21714 @ @ 1
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.: Start of measurement range
“Value
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]
Pos: 13 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Important Notes 9
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
Pos: 14 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 1/Wi cht ige Erl äu ter unge n - Ü bers chr ift 1 @ 4\mod_1241428899156_21.docx @ 32170 @ 1 @ 1
2 Important Notes
Pos: 15.1 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Wi chtig e Er l äuter ung en - Ei nleit ung @ 3\mod_1221059818031_21.docx @ 21717 @ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 15.2 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Rec htl ic he Gr un dlag en - Über schri ft 2 @ 3\mod_1221060626343_21.docx @ 21726 @ 2 @ 1
2.1 Legal Bases
Pos: 15.3 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Änd er ungs vor beh alt - Über schr ift 3 und In halt @ 3\mod_1221060036484_21.docx @ 21720 @ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all
rights arising from the granting of patents or from the legal protection of utility
patents. Third-party products are always mentioned without any reference to
patent rights. Thus, the existence of such rights cannot be excluded.
Pos: 15.4 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Pers onalq uali fikati on/Per sonal qual ifik ation 7 50-xxxx - Ü bers chri ft 3 un d In halt @ 3\mod_1224061208046_21.docx @ 24063 @ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos: 15.5 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Bes timmu ngsg emäße V erwe ndung/ Besti mmung sgem äße Ver wendu ng 750- xxxx - Üb ersc hrift 3 u nd Inhalt @ 3\mod_1224064151234_21.docx @ 24070 @ 3 @ 1
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions
Fieldbus couplers, fieldbus controllers and I/O modules found in the modular
WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and
transmit them to actuators or higher-level control systems. Using programmable
controllers, the signals can also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO-I/O-SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information
in the section “Device Description> “Standards and Guidelines” in the manual
for the used fieldbus coupler/controller.
Appropriate housing (per 2014/34/EU) is required when operating the WAGO-
I/O-SYSTEM 750 in hazardous environments. Please note that a prototype test
10 Important Notes WAGO-I/O-SYSTEM 750
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
Pos: 15.6 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Te chni sc her Z us tand der Ger ät e - Ü bersc hri ft 3 und Inh alt @ 3\mod_1221060446109_21.docx @ 21723 @ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. WAGO
Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of
changes in hardware or software as well as to non-compliant usage of devices.
Please send your request for modified and new hardware or software
configurations directly to WAGO Kontakttechnik GmbH & Co. KG.
Pos: 15.7 /Dokumentation all ge mein/ Glie der ungs ele mente /---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Important Notes 11
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
Pos: 15.8 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Sic her hei tshi n weise - Üb ersc hrift 2 @ 6\ mod_1260180299987_21.docx @ 46724 @ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 15.9 /All e Seri en ( All ge meine Mo dul e)/ Sich erh eits- und s onsti ge H in weis e/Ei nl eit ung Sich erh eits hin weis e H ard ware @ 6\mod_1260180170493_21.docx @ 46720 @ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 15.1 0. 1 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /G efa hr/G efahr : N ich t an G erät en unter S pann ung ar beite n! @ 6\ mod_1260180365327_21.docx @ 46727 @ @ 1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: 15.1 0. 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/G ef ahr/ Gefa hr: Ei nbau 07 50- xxxx nur in Geh äusen, S chrä nken oder ele ktrisc hen Betr iebsr äume n! @ 6\mod_1260180556692_21.docx @ 46731 @ @ 1
Install the device only in appropriate housings, cabinets or in electrical
operation rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Pos: 15.1 0. 3 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /G efa hr/G efahr : U nfal l verh ütung s vorsc hri ft en b each ten! @ 6\mod_1260180657000_21.docx @ 46735 @ @ 1
Pos: 15.1 0. 4 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /G efa hr/G efahr : A uf nor mger ec hte n Ansc hl uss ac hten! @ 6\mod_1260180753479_21.docx @ 46739 @ @ 1
Pos: 15.1 1. 1 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und sonstige Hinweise/Achtung/Achtung: Defekte oder bes chädig te Ger äte aus tausc hen! @ 6\ mod_1260180857358_21.docx @ 46743 @ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Pos: 15.1 1. 2 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /A chtu ng/A cht ung : G erät e vor kriec hen den und isol i ere nden Sto ffen sc hütz en! @ 6\ mod_1260181036216_21.docx @ 46747 @ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for handling
devices/modules.
Pos: 15 .11. 3 /Alle Ser ie n (All ge mein e M odul e) /Sic her hei ts- un d s onsti ge Hin wei se/A cht ung /Ac htu ng: R ei nigu ng n ur mit zul ässi ge n Mat eri alie n! @ 6\ mod_1260181203293_21.docx @ 46751 @ @ 1
Clean only with permitted materials!
Clean soiled contacts using oil-free compressed air or with ethyl alcohol and
leather cloths.
Pos: 15.1 1. 4 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und sonstige Hinweise/Achtung/Achtung: Kein Kontaktspray verwenden! @ 6\mod_1260181290808_21.docx @ 46755 @ @ 1
12 Important Notes WAGO-I/O-SYSTEM 750
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos: 15.1 1. 5 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /A chtu ng/A cht ung : V erpol ung en der Dat en- und V ersorg ungsl eitu ngen ver meide n! @ 6\mod_1260184045744_21.docx @ 46767 @ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos: 15.1 1. 6 /Al le S eri en ( Allg em ein e Mo dul e)/Sic her hei ts- un d s onsti ge Hin wei se/A cht ung /Ac htu ng: El e ktr ostati sc he Entl adu ng verm ei den! @ 6\ mod_1260181364729_21.docx @ 46759 @ @ 1
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
Pos: 16 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Device Description 13
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
Pos: 17 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 1/G erät e besc hrei bung - Ü ber schri ft 1 @ 3\mod_1233756084656_21.docx @ 27096 @ 1 @ 1
3 Device Description
Pos: 18.1 .1 /Ser ie 7 50 ( WAG O-I/ O-SYSTEM)/Gerätebeschreibung/Einleitung/Anwendung/AO/Anwendung 750-05x x AO E x i Zon e 0/ 1 ( 4... 20 mA) @ 12 \mod_1337840910368_21.docx @ 95487 @ @ 1
The analog output module 750-586 (2AO 4-20mA Ex i) generates a standardized
signal of 4 … 20 mA for hazardous field area of zone 0 or zone 1.
Pos: 18.1 .2 /Ser ie 7 50 ( WAG O-I/ O-SYSTEM)/Wichtige Erläuterungen/Sicherheits- und so nstige Hi nwei s e/War nung / Warn ung: E x i I nst allati o n des WA GO-I/ O-SY STEM 7 50 nur in Zone 2 oder im nicht -ex-Bereic h @ 5\mod_1245851655116_21.docx @ 35947 @ @ 1
Installation only in zone 2 or in non-hazardous environments!
The installation of the WAGO-I/O-SYSTEM 750 fieldbus couplers/controllers
and I/O modules is only to be done in zone 2 or in non-hazardous environments.
Pos: 18.1 .3 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/I/ O-B esc hrei bung /AO/ I/O- Besc hreib ung 750- 05x x 2 AO 2-Lei ter ( AO und 0V) @ 5\mod_1247048703979_21.docx @ 36857 @ @ 1
The module has 2 output channels and enables, for example, the direct wiring of 2
2-conductor actuators. The actuators are connected to the CAGE CLAMP
®
connectors AO 1 and 0V or AO 2 and 0V.
Pos: 18.1.4 /Serie 750 (WAGO-I/O-S YSTEM )/G erä teb eschr ei bung/ Einl eitu ng/I /O-B esc hrei bung /AO/ I/O- Bes chrei bung 7 50-05xx AO Gemei nsam er Schir mans chlus s @ 12\mod_1337841659376_21.docx @ 95495 @ @ 1
The output channels of this module have a common shield (screen) connection.
Pos: 18.1 .5 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/I/ O-B esc hrei bung /All ge mein /V er weis a uf Kapi tel " A nsc hlüss e" @ 8\ mod_1276775378035_21.docx @ 57956 @ @ 1
The assignment of the connections is described in the “Connectors” section.
Pos: 18.1 .6 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/I/ O-B esc hrei bung /All ge mein /V er weis a uf Kapi tel " G erät e an schl ieß en" > " Ansc hl ussb eis piel (e) " @ 5\mod_1246015203281_21.docx @ 36298 @ @ 1
Connection examples are shown in section “Connect Devices” > … >
“Connection Example(s)”.
Pos: 18.1 .7 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erä teb esc hrei bu ng/Ei nlei tu ng/V ers org ung/ An ord nung in Ex i- Segment beliebig @ 4\mod_1241506600203_21.docx @ 32297 @ @ 1
Any configuration of the I/O module is possible within an intrinsically safe
segment when configuring the fieldbus node. An arrangement in groups within the
group of potentials is not necessary.
Pos: 18.1 .8 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/Ei ns atz berei ch/Ei ns atz ber eich 75 0-x xxx alle Kop pler /Contr oller ohne Eco nom y-Koppl er @ 3\ mod_1232541867468_21.docx @ 26525 @ @ 1
The I/O module 750-586 can be used with all fieldbus couplers/controllers of the
WAGO-I/O-SYSTEM 750 (except for the economy types 750-320, -323, -324
and -327).
Pos: 18.1 .9 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/L ED-A nzeig e/LED Zustan d Betr ieb Kanal @ 5\mod_1245391732046_21.docx @ 35668 @ @ 1
The operating status of the channels is indicated by a green status LED per
channel.
Pos: 18.1 .1 0 /S erie 750 ( W AGO -I/O-SY ST EM)/ Gerät ebe schr eib ung/ Einl eit ung/ LED -Anz eige /V erwei s a uf K api tel " A nzeig eel e ment e" @ 5 \mod_1246010525000_21.docx @ 36194 @ @ 1
The meaning of the LEDs is described in the Display Elements” section.
Pos: 18.1 .1 1 /S erie 750 ( W AGO -I/O-SY ST EM) /Ger äte bes chr eib ung/ Einl eit ung/ V ersor gu ng/V ers org ung 24 V , 0 V üb er L eist u ngs kont akte Ex i @ 4\mod_1242218496140_21.docx @ 33110 @ @ 1
The Ex i I/O module receives the 24 V voltage supply for the field level from an
upstream Ex i I/O module or from an Ex i power supply module via the power
contacts used as blade contacts. It then provides this potential to subsequent I/O
modules via the power contacts used as spring contacts.
Pos: 18 .1.1 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Ger äte bes chr eib ung/ Einl eit ung/ V ersor gu ng/G al vanisc h e Tre nnu ng F eld/ S yste m @ 3\mod_1233756478750_21.docx @ 27102 @ @ 1
The field voltage and the system voltage are electrically isolated from each other.
Pos: 18 .2 /Dokumentation allgemein/Gliederungselemente/---Seite nwe chsel --- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
14 Device Description WAGO-I/O-SYSTEM 750
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
Pos: 18.3 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ A nsich t - Ü bers chr ift 2 @ 4\mod_1240984217343_21.docx @ 31958 @ 2 @ 1
3.1 View
Pos: 18.4 /Serie 750 (WAGO-I/O-S YSTEM) /Ger äteb eschrei bung /Ansic ht/A nalog ausg angs klemm en/Ansi cht 7 50-058 6 - Ab b. @ 12\mod_1337680789995_21.docx @ 95420 @ @ 1
Figure 1: View
Pos: 18.5 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /Ans ic ht/ Ansi cht C ag eCl amp® _ Lege nde mit LEDs , mit 1 E ntrieg el ung slas ch e @ 1 5\mod_1370867188922_21.docx @ 122225 @ @ 1
Table 3: Legend for Figure “View”
Description
Details See Section
Marking possibility with Mini-
WSB
---
Status LEDs
“Device Description” > “Display Elements”
Data contacts
“Device Description” > “Connectors”
CAGE CLAMP
®
connectors
“Device Description” > “Connectors”
Power jumper contacts
“Device Description” > “Connectors”
Release tab
“Mounting” > “Inserting and Removing
Devices”
Pos: 18.6 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Device Description 15
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
Pos: 18 .7 /All e Ser i en (A llg emei ne M od ule) /Ü bers chri fte n/Eb ene 2/ Ansc hlüs se - Üb ersc hri ft 2 @ 4 \mod_1240984262656_21.docx @ 31961 @ 2 @ 1
3.2 Connectors
Pos: 18.8 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/A nsc hlüss e/D ate nkon takt e/Kl em menbus - Ü bersc hrift 3 @ 6\mod_1256294684083_21.docx @ 43660 @ 3 @ 1
3.2.1 Data Contacts/Internal Bus
Pos: 18.9 .1 /Ser ie 7 50 ( WAG O-I/ O-SYSTEM)/Gerätebeschreibung/Anschlüsse/Datenkontakte - Feld bus koppl er/-c ont roll er, Ab bild ung und Bes chr ei bung @ 3\ mod_1231771259187_21.docx @ 26002 @ @ 1
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the internal bus. It
is comprised of 6 data contacts, which are available as self-cleaning gold spring
contacts.
Figure 2: Data Contacts
Pos: 18.9 .2 /Ser ie 7 50 ( WAG O-I/ O-SYSTEM)/Wichtige Erläuterungen/Sicherheits- und sons tige Hi nwei s e/Ach tu ng/A cht ung : Bus kle mm en ni cht auf Gol df eder kon tak te l eg en! @ 7\mod_1266318463636_21.docx @ 50695 @ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos: 18.9 .3 /Ser ie 7 50 ( WAG O-I/ O-SYSTEM)/Wichtige Erläuterungen/Sicherheits- und sonstige Hinweise/Achtung/Achtung: ESD - Auf g ute Erd ung der Umg eb ung ac hte n! @ 7\mod_1266318538667_21.docx @ 50708 @ @ 1
Ensure that the environment is well grounded!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, ensure that the environment
(persons, workplace and packing) is well grounded. Avoid touching conductive
components, e.g. data contacts.
Pos: 18.1 0 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1
16 Device Description WAGO-I/O-SYSTEM 750
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
Pos: 18 .11 / Ser ie 7 50 ( WAG O-I/ O-SYST EM) /Ger äte besc hrei bu ng/A nsc hlüss e/L eist ungs ko ntakt e/F eldv ers orgung - Ü bers chri ft 3 @ 6\mod_1256294692864_21.docx @ 43664 @ 3 @ 1
3.2.2 Power Jumper Contacts/Field Supply
Pos: 18.1 2. 1 /S erie 750 ( W AGO -I/O-SY ST EM)/Wi chtig e Er l äuter ung en/Si cher hei ts- und s ons tig e Hi nw eise /Vor sich t/ Vorsi cht : V erlet zu ngsg ef ahr d urc h sc har f kantig e M ess erk onta kt e! @ 6\mod_1256193279401_21.docx @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
Pos: 18.1 2. 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Ger äte bes chr eib ung/ Ans chl üss e/L eist ungs kon tak te 2 LK ( M esser /Fe der ) - Ei nlei tu ng @ 15\ mod_1371721641099_21.docx @ 123714 @ @ 1
The I/O module 750-586 has 2 self-cleaning power jumper contacts that supply
and transmit power for the field side. The contacts on the left side of the I/O
module are designed as blade contacts and those on the right side as spring
contacts.
Pos: 18 .12. 3 /Serie 75 0 (W AGO-I/O- SYST EM )/G erät ebe schr ei bung /A nsc hlüss e/ Leis tung sk onta kt e 2 L K (M ess er/F ed er) - Abbildung, doppelte Breite @ 15\mod_1371721756578_21.docx @ 123718 @ @ 1
Figure 3: Power Jumper Contacts
Pos: 18 .12. 4 /Serie 75 0 (WAG O-I/O- SYST EM) /Ger äte bes chr eib ung/ Ans chl üss e/L eist ungs kon tak te 2 LK ( M esser /Fe der ) - Legende @ 15\mod_1371721352500_21.docx @ 123710 @ @ 1
Table 4: Legend for Figure “Power Jumper Contacts”
Contact
Type
Function
1
Spring contact
Potential transmission (U
v
) for field supply
2
Spring contact
Potential transmission (0 V) for field supply
3
Blade contact
Potential feed-in (0 V) for field supply
4
Blade contact
Potential feed-in (U
v
) for field supply
Pos: 18 .12. 5 /Serie 75 0 (WAG O-I/O- SYST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/H in weis /Hi nwei s: M axi mal er St ro m E x i E ins peis ung 75 0-06xx 1,0 A @ 7\mod_1274358256668_21.docx @ 56898 @ @ 1
Do not exceed maximum current via power contacts!
The maximum current available from the 750-606 or 750-625/000-001 Ex-i
Supply Module is 1 A.
When configuring the system, ensure that this current is not exceeded.
If exceeded, an additional potential feed module must be used.
Pos: 18.1 3 /D ok um entati o n allg em ein/Gl i ederu ngsel e ment e/---Seit enw echs el--- @ 3 \mod_1221108045078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Device Description 17
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
Pos: 18.1 4 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung /A nsc hlüss e/C AGE C L AMP-A nschlüsse - Ü bersc hrift 3 @ 6\mod_1256296337770_21.docx @ 43674 @ 3 @ 1
3.2.3 CAGE CLAMP
®
Connectors
Pos: 18.1 5 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung /A nsc hlüss e/A nal oga usg ang skle mm en/A nsc hlüs se 7 50- 058 5,-0586 @ 12\mod_1337681021342_21.docx @ 95424 @ @ 1
Figure 4: CAGE CLAMP
®
Connectors
Table 5: Legend for Figure “CAGE CLAMP
®
Connectors”
Channel
Designation
Connector
Function
1
AO 1 1 Output AO 1: Signal voltage
0 V 3 Output AO 1: Actuator supply 0 V
S 4 Output AO 1: Shield connection
2
AO 2 5 Output AO 2: Signal voltage
0 V 7 Output AO 2: Actuator supply 0 V
S 8 Output AO 2: Shield connection
Pos: 18.1 6 /D ok um entati o n allg em ein/Gl i ederu ngsel e ment e/---Seit enw echs el--- @ 3 \mod_1221108045078_0.docx @ 21810 @ @ 1
18 Device Description WAGO-I/O-SYSTEM 750
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
Pos: 18.1 7 / Alle Ser ie n (All ge mein e M odul e) /Üb ersc hri ften /Eb ene 2/ Anzei ge ele ment e - Ü bersc hrift 2 @ 4\ mod_1240984390875_21.docx @ 31964 @ 2 @ 1
3.3 Display Elements
Pos: 18.1 8 / Ser ie 7 50 ( WAG O-I/ O-SYST EM)/ Gerät ebesc hreib ung/ Anzeig eele mente/ Anal ogaus gangs klem men/A nzeig eele mente 75 0-05xx Ex 2AO (Agn, Cgn) @ 5\mod_1246000589437_21.docx @ 36152 @ @ 1
Figure 5: Display Elements
Table 6: Legend for Figure “Display Elements
Channel
Designation
LED
State
Function
1 Status AO 1 A
Off
No operational readiness or the internal
data bus communication is interrupted
Green
Operational readiness and trouble-free
internal data bus communication
2 Status AO 2 E
Off
No operational readiness or the internal
data bus communication is interrupted
Green
Operational readiness and trouble-free
internal data bus communication
Pos: 18.1 9 / Alle Ser ie n (All ge mein e M odul e) /Üb ersc hri ften /Eb ene 2/ Bedie nel em ente - Üb ersc hrift 2 @ 4\mod_1239191655456_21.docx @ 30439 @ 2 @ 1
3.4 Operating Elements
Pos: 18.2 0 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung /B edien el eme nte/ Bedi en ele ment e I/ O-Modul 75x-xxxx nicht vor hande n @ 4\mod_1236322031125_21.docx @ 28063 @ @ 1
The I/O module 750-586 has no operating elements.
Pos: 18.2 1 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Device Description 19
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
Pos: 18.2 2 / Alle Ser ie n (All ge mein e M odul e) /Üb ersc hri ften /Eb ene 2/ Sche mati sc hes S ch alt bild - Ü b erschr if t 2 @ 4 \mod_1240984441312_21.docx @ 31967 @ 2 @ 1
3.5 Schematic Diagram
Pos: 18.2 3 / Ser ie 7 50 ( WAG O-I/ O-SYST EM)/ Gerät ebesc hreib ung/ Schem atisc he Schal tbild er/A nalog ausg angskl emme n/Sc hematis ches Schalt bild 750- 05 86 @ 12\mod_1337681229055_21.docx @ 95428 @ @ 1
Figure 6: Schematic Diagram
Pos: 18.2 4 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1
20 Device Description WAGO-I/O-SYSTEM 750
750-586 2AO 4-20mA Ex i
Manual
Version 1.2.0 HW-Version 05, SW-Version 3A
Pos: 18.2 5 / Alle Ser ie n (All ge mein e M odul e) /Üb ersc hri ften /Eb ene 2/T ec hnisc he D at en - Ü bersc hrift 2 @ 3\mod_1232967587687_21.docx @ 26924 @ 2 @ 1
3.6 Technical Data
Pos: 18.2 6 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung /Tec h nisch e D ate n/An alog ausg ang s kle mme n/Tec hnis ch e D aten 75 0-0 586 @ 12\ mod_1337674852719_21.docx @ 95372 @ 33333 @ 1
3.6.1 Device Data
Table 7: Technical Data ‒ Device
Width
24 mm
Height (from upper edge of 35 DIN rail)
64 mm
Depth
100 mm
Weight
approx. 91.6 g
3.6.2 Supply
Table 8: Technical Data ‒ Supply
Voltage supply
Via system voltage terminal bus
(5 V DC) and power contacts (24 V DC)
Current consumption
typ
. (internal).
(5 V DC)
21 mA
Input current
typ
. (field)
(24 V DC)
19 mA / + load (2 x 20 mA)
Voltage via power jumper contacts
24 V DC (supply via Ex i supply
module U
0
= max. 27.3 V)
Current via power contacts
max.
1000 mA
Power loss P
V
0.9 W
Power consumption P
max.
1.5 W
Isolation
300 VAC system/supply
3.6.3 Communication
Table 9: Technical Data ‒ Communication
Internal bit width (terminal bus)
2 x 16 bits data,
2 x 8 bits control/status (optional)
3.6.4 Outputs
Table 10: Technical Data ‒ Outputs
No. of outputs
2
Signal current
4 mA … 20 mA
Load impedance
< 500 Ω
Linearity
± 2 LSB
Resolution
12 Bit
Conversion time
< 2 ms
Output error 25°C
< ±0.2 % from full scale range
Temperature coefficient
< ±0.01 % / K from full scale range
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

WAGO 2-channel, 4 - 20 mA, Ex i User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI