WAGO RS-232/RS-485 Serial Interface User manual

Pos: 2 /Dokumentation allgemein/Einband/Einband Handbuch - Fronts eite 20 15 - mit Doc Var iabl en ( Sta ndar d) @ 9\ mod_1285229289866_0.docx @ 64941 @ @ 1

WAGO-I/O-SYSTEM 750

Manual

753-652

Serial Interface RS-232 / RS-

485

Configurable

Version 2.0.0

Pos: 3 /A lle Ser ien ( All ge mein e M odul e)/ Rec htlic h es, A llg emei nes /Im pre ssu m f ür St and ard han dbüc her - al lg. Ang aben, A nschr iften, Telefo nnum mern un d E-Mail- Adres sen @ 3\mod_1219151118203_21.docx @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: documentation@wago.com

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

=== Ende der Lis te f ür T e xtmar ke Ei nb and _vor ne = ==

WAGO-I/O-SYSTEM 750 Table of Contents 3

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

Pos: 5 /D ok ument ati on al lg em ein/V erz eic hni sse /Inh alts ver zei chni s - Ü bersc hrift oG und Ver zeich nis @ 3\mod_1219151230875_21.docx @ 21063 @ @ 1

Table of Contents

1 Notes about this Documentation ................................................................. 6

1.1 Validity of this Documentation ................................................................. 6

1.2 Copyright ................................................................................................... 6

1.3 Symbols ..................................................................................................... 7

1.4 Number Notation ....................................................................................... 9

1.5 Font Conventions ...................................................................................... 9

2 Important Notes ......................................................................................... 10

2.1 Legal Bases ............................................................................................. 10

2.1.1 Subject to Changes ............................................................................. 10

2.1.2 Personnel Qualifications ..................................................................... 10

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with

Underlying Provisions ........................................................................ 10

2.1.4 Technical Condition of Specified Devices ......................................... 11

2.2 Safety Advice (Precautions) .................................................................... 12

3 Device Description ..................................................................................... 14

3.1 View ........................................................................................................ 18

3.2 Connectors ............................................................................................... 19

3.2.1 Data Contacts/Internal Bus ................................................................. 19

3.2.2 Power Jumper Contacts/Field Supply ................................................ 20

3.2.3 CAGE CLAMP

®

Connectors ............................................................. 22

3.3 Display Elements .................................................................................... 24

3.4 Operating Elements ................................................................................. 25

3.5 Schematic Diagram ................................................................................. 26

3.6 Technical Data ........................................................................................ 27

3.6.1 Device Data ........................................................................................ 27

3.6.2 Supply ................................................................................................. 27

3.6.3 Communication .................................................................................. 28

3.6.4 Interface .............................................................................................. 28

3.6.5 Connection .......................................................................................... 28

3.6.6 Climatic Environmental Conditions ................................................... 29

3.7 Approvals ................................................................................................ 30

3.8 Standards and Guidelines ........................................................................ 32

4 Process Image ............................................................................................. 33

4.1 Operating Modes for Serial Transmission .............................................. 33

4.2 Data Exchange Mode .............................................................................. 35

5 Function Description ................................................................................. 37

5.1 Operating Modes for Serial Transmission .............................................. 37

5.1.1 Transmit Data ..................................................................................... 37

5.1.1.1 Continuous Transmission .............................................................. 37

5.1.2 Receive Data ....................................................................................... 38

5.1.2.1 Continuous Receipt ........................................................................ 38

5.1.3 RS-232 Operating Mode..................................................................... 38

5.1.3.1 Flow Control Using XON-/XOFF Protocol .................................. 39

5.1.3.2 Flow Control Using RTS/CTS ....................................................... 39

5.1.3.3 Flow Control Using RTS/CTS, RTS with Lead/Follow-on Time . 39

4 Table of Contents WAGO-I/O-SYSTEM 750

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

5.1.4 RS-485 Operating Mode..................................................................... 39

5.1.5 RS-422 Operating Mode..................................................................... 40

5.1.6 DMX Operating Mode ....................................................................... 40

5.1.6.1 Sending Data Packets in DMX Mode ............................................ 40

5.1.6.2 Receiving Data Packets in DMX Mode ......................................... 41

5.2 Data Exchange Operating Mode ............................................................. 41

6 Mounting ..................................................................................................... 43

6.1 Mounting Sequence ................................................................................. 43

6.2 Inserting and Removing Devices ............................................................ 44

6.2.1 Inserting the I/O Module .................................................................... 44

6.2.2 Removing the I/O Module .................................................................. 45

6.3 I/O Modules with Pluggable Wiring Level (Series 753) ........................ 46

6.3.1 Coding ................................................................................................ 47

6.3.2 Connector Removal ............................................................................ 49

7 Connect Devices ......................................................................................... 50

7.1 Connecting a Conductor to the CAGE CLAMP

®

................................... 50

7.2 Connection Examples .............................................................................. 51

7.2.1 RS-232 Operating Mode..................................................................... 51

7.2.2 RS-485 Operating Mode..................................................................... 52

7.2.3 RS-422 Operating Mode..................................................................... 54

7.2.4 DMX Operating Mode ....................................................................... 54

7.2.5 Data Exchange Mode ......................................................................... 55

8 Commissioning ........................................................................................... 56

8.1 Configuration and Parameterization with WAGO-I/O-CHECK ............. 56

8.1.1 RS-232/RS-485 Serial Interface (Configuration Dialog) ................... 57

8.1.2 Toolbar on the Configuration Dialog ................................................. 57

8.1.3 Process Image Size ............................................................................. 58

8.1.4 Parameter Range ................................................................................. 59

8.1.5 Setting the RS-232/RS-485 Serial Interface ....................................... 61

8.2 Configuration and Parameterization via GSD File with PROFIBUS

DP and PROFINET IO ............................................................................ 61

8.3 Data Transfer ........................................................................................... 62

8.3.1 Example of Operating Modes for Serial Transmission ...................... 62

8.3.2 Initialization ........................................................................................ 63

8.3.3 Transmission of the Character String "Hello World!" ....................... 64

8.3.4 Receiving the Character String "WAGO" .......................................... 64

8.3.5 Operation with Continuous Send........................................................ 65

8.3.5.1 Transmission of a Block of One to 512 Bytes ............................... 65

8.3.5.2 Transmission of a Block of More than 512 Bytes ......................... 66

8.3.6 DMX Application Example ................................................................ 68

8.3.6.1 Operation with Deactivated Continuous Send ............................... 68

8.3.6.2 Operation with Activated Continuous Send .................................. 68

8.3.6.3 Mode when Receiving DMX Data ................................................ 69

8.3.6.3.1 “DMX Receive” Operating Parameters .................................... 70

8.3.6.3.2 “DMX Receive” Application Example ..................................... 71

8.3.7 Data Exchange Operating Mode Application Example ..................... 73

WAGO-I/O-SYSTEM 750 Table of Contents 5

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

9 Diagnostics .................................................................................................. 74

9.1 Serial Operating Modes RS-232, RS-422 and RS-485 ........................... 74

9.2 DMX Operating Mode ............................................................................ 74

9.3 Data Exchange Operating Mode ............................................................. 75

10 Use in Hazardous Environments .............................................................. 76

10.1 Marking Configuration Examples ........................................................... 77

10.1.1 Marking for Europe According to ATEX and IEC-Ex ...................... 77

10.1.2 Marking for America According to NEC 500 .................................... 82

10.2 Installation Regulations ........................................................................... 83

10.2.1 Special Conditions for Safe Use

(ATEX Certificate TÜV 07 ATEX 554086 X) .................................. 84

10.2.2 Special Conditions for Safe Use

(ATEX Certificate TÜV 12 ATEX 106032 X) .................................. 85

10.2.3 Special Conditions for Safe Use

(IEC-Ex Certificate TUN 09.0001 X) ................................................ 86

10.2.4 Special Conditions for Safe Use

(IEC-Ex Certificate IECEx TUN 12.0039 X) .................................... 87

10.2.5 Special Conditions for Safe Use According to ANSI/ISA 12.12.01 .. 88

11 Appendix ..................................................................................................... 89

11.1 Configuration and Parameterization via GSD File ................................. 89

11.1.1 Configuration of the RS-232/RS-485 Interface .................................. 89

11.1.1.1 PROFIBUS DP Fieldbus Coupler/Controller

750-333(/0xx-000), 750-833(/0xx-000),

PROFINET IO Fieldbus Coupler (750-370) ................................. 89

11.1.1.2 PROFINET IO Fieldbus Coupler 750-375(/025-000),

750-377(/025-000) ......................................................................... 89

11.1.2 Configuration of the RS-232/RS-485 Serial Interface ....................... 90

11.1.2.1 All PROFIBUS DP and PROFINET IO Fieldbus

Couplers/Controllers ...................................................................... 91

11.1.2.2 PROFIBUS DP Fieldbus Coupler/Controller 750-333(/0xx-000),

750-833(/0xx-000), PROFINET IO Fieldbus Coupler 750-370 .... 93

11.1.2.3 PROFINET IO Fieldbus Coupler 750-375(/025-000),

750-377(/025-000) ......................................................................... 94

List of Figures ...................................................................................................... 95

List of Tables ........................................................................................................ 97

=== Ende der Lis te f ür T e xtmar ke V erz eic hnis _vor ne == =

6 Notes about this Documentation WAGO-I/O-SYSTEM 750

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

Pos: 7 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten/ Ebe ne 1/Hi nwei s e zu dies er D o kume ntati on - Über schr ift 1 @ 4\mod_1237987661750_21.docx @ 29029 @ 1 @ 1

1 Notes about this Documentation

Pos: 8 /A lle Ser ien ( All ge mein e M odul e)/ Sic her heit s- und sonstige Hinweise/Hinweis/Hinweis: Dokumentation aufbewahren @ 4\mod_1237987339812_21.docx @ 29026 @ @ 1

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation is

included, if necessary.

Pos: 9 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten/ Ebe ne 2/G ültig kei tsb ereic h - Über schr ift 2 @ 12\mod_1338912448776_21.docx @ 96469 @ 2 @ 1

1.1 Validity of this Documentation

Pos: 10 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/G ülti gkei ts berei c h/Gül tig kei tsber ei ch D okumentation Busklemme 750-xxxx, oh ne V aria nten ang abe @ 14\mod_1358944037947_21.docx @ 109346 @ @ 1

This documentation is only applicable to the I/O module 753-652

(Serial Interface RS-232 / RS-485).

Pos: 11 /S eri e 7 50 ( WA GO-I/O-SYST EM) /Hi n weis e zur D okum ent ati on/Hi nw eise /Ac htu ng: H in weis zur D oku ment ati on B uskl e mmen 750- xxxx @ 4\mod_1237986979656_21.docx @ 29023 @ @ 1

The I/O module 753-652 shall only be installed and operated according to the

instructions in this manual and in the manual for the used fieldbus

coupler/controller.

Consider power layout of the WAGO-I/O-SYSTEM 750!

In addition to these operating instructions, you will also need the manual for the

used fieldbus coupler/controller, which can be downloaded at www.wago.com.

There, you can obtain important information including information on electrical

isolation, system power and supply specifications.

Pos: 12.1 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Ur heb ersc hut z - Ü bersc hr ift 2 @ 23\ mod_1435647042188_21.docx @ 184808 @ 2 @ 1

1.2 Copyright

Pos: 12.2 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Ur heb ersc hut z au sf ührli ch @ 4\mod_1235565145234_21.docx @ 27691 @ @ 1

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 12 .3 /Dokumentation allgemein/Gliederungselemente/---Seite nwe chsel --- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

Pos: 12.4 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ S ymbol e - Ü ber schr if t 2 @ 13\ mod_1351068042408_21.docx @ 105270 @ 2 @ 1

1.3 Symbols

Pos: 12 .5.1 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und so nsti ge H in weis e/G efa hr/G efa hr: _War nu ng vor P ers on ensc hä den allg emei n_ - Erl äuter ung @ 13\ mod_1343309450020_21.docx @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12 .5.2 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonsti ge Hin weise/ Gefa hr/Gef ahr: _ Warnu ng vor Per son ensch äden d urch ele ktrisc hen Str om_ - Erl äut eru ng @ 13\mod_1343309694914_21.docx @ 101030 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12 .5.3 /Al le Seri en (All gemei ne Mod ule)/ Sich erh eits- und sons tig e Hi n weis e/W arnung / Warn ung: _ Warn ung vor P erso nensc h äde n all gem ei n_ - Erläuterung @ 13\mod_1343309877041_21.docx @ 101035 @ @ 1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 12 .5.4 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonsti ge Hin weise/ Vorsic ht/V orsic ht: _War nung vor Pers one nschäd en allg emein _ - Erläuterung @ 13\mod_1343310028762_21.docx @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 12 .5.5 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonsti ge Hin weise/ Achtu ng/A chtung : _War nung v or Sachsc häden allgemein_ - Erläuterung @ 13\mod_1343310134623_21.docx @ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12 .5.6 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonsti ge Hin weise/ Achtu ng/A chtung : _War nung v or Sachsc häd en durc h elektr ostati sch e Aufla dung_ - Erläut erung @ 13\mod_1343310227702_21.docx @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12 .5.7 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonstige Hinweise/Hinweis/Hinweis: _Wichtiger Hinweis allgemein_ - Erläuterung @ 13\mod_1343310326906_21.docx @ 101047 @ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 12 .5.8 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und so nsti ge H in weis e/I nfor mat ion/ Inf or mati on: _W eiter e I nfor mation al lge mein_ - Erl äuter ung @ 13 \mod_1343310439814_21.docx @ 101051 @ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 12.6 /Dokumentation allgemein/Gli eder ungs ele ment e/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 9

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

Pos: 12.7 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Dar st ellu ng der Z ahl ens yst eme - Über sc hrift 2 @ 2 3\mod_1435647128078_21.docx @ 184811 @ 2 @ 1

1.4 Number Notation

Pos: 12.8 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Za hlens ys te me @ 3\mod_1221059454015_21.docx @ 21711 @ @ 1

Table 1: Number Notation

Number Code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated with

dots (.)

Pos: 12.9 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Sc hri ftk on venti one n - Ü bersc hri ft 2 @ 23\mod_1435647186005_21.docx @ 184814 @ 2 @ 1

1.5 Font Conventions

Pos: 12.1 0 / Alle Ser ie n (All ge mein e M odul e) /Re chtl ich es, Allg em ein es/Sc hr ift konv enti onen @ 3\mod_1221059521437_21.docx @ 21714 @ @ 1

Table 2: Font Conventions

Font Type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Program Files\WAGO Software

Menu

Menu items are marked in bold letters.

e.g.: Save

>

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.: File > New

Input

Designation of input or optional fields are marked in bold letters,

e.g.: Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.: [F5]

Pos: 13 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078 _0. doc x @ 2 181 0 @ @ 1

10 Important Notes WAGO-I/O-SYSTEM 750

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

Pos: 14 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 1/Wi cht ige Erl äu ter unge n - Ü bersc hrift 1 @ 4\mod_1241428899156_21.docx @ 32170 @ 1 @ 1

2 Important Notes

Pos: 15.1 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Wi chtig e Er l äuter ung en - Ei nleit ung @ 3\mod_1221059818031_21.docx @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 15.2 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Rec htl ic he Gr un dlag en - Über schri ft 2 @ 3\mod_1221060626343_21.docx @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 15.3 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Änd er ungs vor beh alt - Über schr ift 3 und In halt @ 3\mod_1221060036484_21.docx @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications that serve to increase the efficiency of technical

progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from

the granting of patents or from the legal protection of utility patents. Third-party

products are always mentioned without any reference to patent rights. Thus, the

existence of such rights cannot be excluded.

Pos: 15.4 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Pers onalq uali fikati on/Per sonal qual ifik ation 7 50-xxxx - Ü bers chri ft 3 un d In halt @ 3\mod_1224061208046_21.docx @ 24063 @ 3 @ 1

2.1.2 Personnel Qualifications

All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be

carried out by electrical specialists with sufficient knowledge in automation. The

specialists must be familiar with the current norms and guidelines for the devices

and automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: 15.5 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Bes timmu ngsg emäße V erwe ndung/ Besti mmung sgem äße Ver wendu ng 750- xxxx - Üb ersc hrift 3 u nd Inhal t @ 3\mod_1224064151234_21.docx @ 24070 @ 3 @ 1

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with

Underlying Provisions

Fieldbus couplers, fieldbus controllers and I/O modules found in the modular

WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and

transmit them to actuators or higher-level control systems. Using programmable

controllers, the signals can also be (pre-) processed.

The devices have been developed for use in an environment that meets the IP20

protection class criteria. Protection against finger injury and solid impurities up to

12.5 mm diameter is assured; protection against water damage is not ensured.

Unless otherwise specified, operation of the devices in wet and dusty

environments is prohibited.

Operating the WAGO-I/O-SYSTEM 750 devices in home applications without

further measures is only permitted if they meet the emission limits (emissions of

interference) according to EN 61000-6-3. You will find the relevant information

in the section “Device Description” > “Standards and Guidelines” in the manual

for the used fieldbus coupler/controller.

WAGO-I/O-SYSTEM 750 Important Notes 11

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

Appropriate housing (per 2014/34/EU) is required when operating the WAGO-

I/O-SYSTEM 750 in hazardous environments. Please note that a prototype test

certificate must be obtained that confirms the correct installation of the system in

a housing or switch cabinet.

Pos: 15.6 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Te chni sc her Z us tand der Ger ät e - Ü bersc hri ft 3 und Inh alt @ 3\mod_1221060446109_21.docx @ 21723 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The devices to be supplied ex works are equipped with hardware and software

configurations, which meet the individual application requirements. WAGO

Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of

changes in hardware or software as well as to non-compliant usage of devices.

Please send your request for modified and new hardware or software

configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

Pos: 15.7 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

Pos: 15.8 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Sic her hei tshi nwei se - Über schr ift 2 @ 6\mod_1260180299987_21.docx @ 46724 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 15.9 /All e Seri en ( All ge meine Mo dul e)/ Sich erh eits- und s onsti ge H in weis e/Ei nl eit ung Sich erh eits hin weis e H ard ware @ 6\mod_1260180170493_21.docx @ 46720 @ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 15.1 0. 1 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /G efa hr/G efahr : N ich t an G erät en unter S pann ung ar beite n! @ 6\ mod_1260180365327_21.docx @ 46727 @ @ 1

Do not work on devices while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: 15.1 0. 2 /S erie 750 ( W AGO- I/O-SY ST EM)/Wi cht ig e Erl äu ter ung en/Si cher hei ts - un d so nstig e Hi n weis e/G efahr /Ge fa hr: Ei nbau 07 50-xx xx nur in Ge häus en, Sc hränke n oder el ektris chen Be trie bsräu men! @ 6\mod_1260180556692_21.docx @ 46731 @ @ 1

Install the device only in appropriate housings, cabinets or in electrical

operation rooms!

The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,

install the system and its components exclusively in appropriate housings,

cabinets or in electrical operation rooms. Allow access to such equipment and

fixtures to authorized, qualified staff only by means of specific keys or tools.

Pos: 15.1 0. 3 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /G efa hr/G efahr : U nfal l verh ütung s vorsc hri ft en b each ten! @ 6\mod_1260180657000_21.docx @ 46735 @ @ 1

Pos: 15.1 0. 4 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /G efa hr/G efahr : A uf nor mger ec hte n Ansc hl uss ac hten! @ 6\mod_1260180753479_21.docx @ 46739 @ @ 1

Pos: 15.1 1. 1 /Al le S eri en ( Allg em ein e Mo dul e)/Sic h erhei ts- un d s onst ige Hi nwei se/ Acht ung /Ac htu ng: Def ekt e od er besc hädig t e Ger ät e aus ta usc hen! @ 6 \mod_1260180857358_21.docx @ 46743 @ @ 1

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts), since the long-term functionality of device/module involved can no

longer be ensured.

Pos: 15.1 1. 2 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und sonstige Hinweise/Achtung/Achtung: Geräte vor kriechenden und isolierenden Stoffen schüt zen! @ 6\mod_1260181036216_21.docx @ 46747 @ @ 1

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for handling

devices/modules.

Pos: 15.1 1. 3 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /A chtu ng/A cht ung : R einig ung nur mi t zul äs sig en M at erial ien! @ 6\mod_1260181203293_21.docx @ 46751 @ @ 1

Clean only with permitted materials!

Clean soiled contacts using oil-free compressed air or with ethyl alcohol and

leather cloths.

Pos: 15.1 1. 4 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und sonstige Hinweise/Achtung/Achtung: Kein Kontaktspray verwenden! @ 6\mod_1260181290808_21.docx @ 46755 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 13

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 15.1 1. 5 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /Ac htu ng/Ac ht ung : Ver pol ung en der Date n- und Ver sorg ungsl eitu ngen ver meide n! @ 6\mod_1260184045744_21.docx @ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 15.1 1. 6 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /A chtu ng/A cht ung : El ektr ost atis ch e En tla dung v ermei de n! @ 6\mod_1260181364729_21.docx @ 46759 @ @ 1

Avoid electrostatic discharge!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge when touched. Please observe the safety precautions

against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the

devices, please ensure that environmental factors (personnel, work space and

packaging) are properly grounded.

Pos: 16 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

14 Device Description WAGO-I/O-SYSTEM 750

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

Pos: 17 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 1/G erät e besc hrei bung - Ü ber schri ft 1 @ 3\mod_1233756084656_21.docx @ 27096 @ 1 @ 1

3 Device Description

Pos: 18.1 /Serie 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/Einleitung/Anwendung/SO/Anwendung 75x-0652_D at ena ust ausc hkl em me @ 15\ mod_1366288638779_21.docx @ 117310 @ @ 1

The I/O module 753-652 (Serial Interface RS-232 / RS-485) allows the optional

connection of devices with a RS-485, RS-422 or RS-232 interface.

It also provides gateways between the serial interface and the fieldbus systems

supported by the WAGO-I/O-SYSTEM 750.

No higher protocol level is required by the module. Communication to the

associated fieldbus master is completely transparent. This provides for a broader

application scope for the serial interface module. If required, communication

protocols can be configured via fieldbus master.

The 2560 byte input buffer provides for high data baud rates. At lower baud rates,

the data received in lower priority tasks is evaluated without data loss.

The 512-byte output buffer provides fast transmission of larger data strings.

The operating mode of the I/O module can be configured using the WAGO-I/O-

CHECK startup tool. Learn what version on WAGO-I/O-CHECK you need in the

table “WAGO-I/O-CHECK Minimum Requirements” in the “Commissioning”

section.

NOTE

The default operating mode is RS-485 half-duplex. The default data transmission

rate is 9600 baud. 1 start bit, 8 data bits and 1 stop bit are sent. There is no parity

generation and dataflow control.

Before starting operation, the connections of the I/O module 753-652 must be

cabled appropriately (see section “Connect Devices” > … > “Connection

Examples”).

In RS-232 mode, the interface works in accordance with the TIA/EIA-232-F and

CCITT V.28/DIN 66259-1 standards.

In RS-485/RS-422 mode, the interface works in accordance with the TIA/EIA-

485-A, DIN 66259 standards.

The connected device can communicate directly with the control unit via the

fieldbus coupler/controller used.

The active communication channel works independent of the fieldbus system used

in full or half-duplex operation at up to 115200 baud.

Pos: 18.2 /Serie 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/Einleitung/Anwendung/SO/Anwendung 750-0652 D at enfl usss teu er ung, D at ena ust ausc h und DM X- Modus @ 15\ mod_1366289566565_21.docx @ 117314 @ @ 1

In the data flow control through RTS/CTS in RS-232 mode, a lead time or follow-

on time can be configured for the I/O module for the RTS signal. This function is

available with firmware version 03 or higher.

Direct data exchange between different fieldbus nodes of the 750 series is possible

in conjunction with a second I/O module 753-652. This function is available with

firmware version 03 or higher.

WAGO-I/O-SYSTEM 750 Device Description 15

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

The I/O module 753-652 can be configured as a DMX device with a baud rate of

250 kBits/s. This function is available with firmware version 03 or higher.

The I/O module 753-652 can be configured as a DMX device at a baud rate of

250 kBits/s. This function is available with firmware version 03 or higher. The

I/O module can be operated as a DMX sender with firmware version 03 or higher

and as a DMX receiver with firmware version 06 or higher.

Pos: 18.3 /Serie 750 (WAGO-I/O-SY STEM )/ Gerät ebes chr eibu ng/Ei nl eitu ng/I/ O-B esc hrei bung /SO/ I/O- Beschreibung 750-0652 – Dat enau st ausc hmod us @ 1 3\mod_1355144859102_21.docx @ 107490 @ @ 1

The wiring to the communication partner takes place in RS-232 mode via the

TxD, RxD connections, if necessary RTS/CTS and ground and in the RS-485/

RS-422 mode via the connections A, B, X, Y, and ground.

Pos: 18.4 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/I/ O-B eschr ei bung/ AI/I /O- Beschr eib ung 750- 04xx AI Schir mansc hluss K onta kt mit Tr agsc hie ne @ 5\mod_1246367742653_21.docx @ 36360 @ @ 1

The shield connection is fed directly to the carrier rail and contact is made

automatically by snapping the module onto the rail.

Pos: 18.5 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/I/ O-Besc hr eibu ng/ All gem ein/ Ver weis auf K apit el " Ansc hl üsse" @ 8\mod_1276775378035_21.docx @ 57956 @ @ 1

The assignment of the connections is described in the “Connectors” section.

Pos: 18.6 /Serie 750 (WAGO-I/O-SYST EM)/ Ger äteb eschr ei bung/ Einl eit ung/ I/O-B esc hrei bu ng/ All gemei n/V er weis auf Ka pitel "G erät e ansc hli eßen" > "A nschl us sbei spi el(e) " @ 5\ mod_1246015203281_21.docx @ 36298 @ @ 1

Connection examples are shown in section “Connect Devices” > … >

“Connection Example(s)”.

Pos: 18.7 /Serie 750 (WAGO-I/O-SY STEM )/ Gerät ebes chr eibu ng/Ei nl eitu ng/L ED-A nzeig e/LED Zust and Betr ieb, Kle mmen bus-Kommunikation und Signalübertragung - mehrf arbig e LEDs @ 6\mod_1257923657453_21.docx @ 44269 @ @ 1

Multi-color LEDs indicate the operating status and the trouble-free internal bus

communication as well as the status of the signal transmission.

Pos: 18.8 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/L ED-A nzeig e/Ver weis au f Kapit el "Anz eige elemen te" @ 5\mod_1246010525000_21.docx @ 36194 @ @ 1

The meaning of the LEDs is described in the “Display Elements” section.

Pos: 18.9 /Serie 750 (WAGO-I/O-SYST EM)/ Ger ätebesc hrei bung/Ei nlei tung /Vers orgung /Vers orgu ng 24 V, 0 V üb er Leis tungs konta kte Sta ndard @ 3\mod_1226498974531_21.docx @ 25020 @ @ 1

The I/O module 753-652 (Serial Interface RS-232 / RS-485) receives the 24 V

voltage supply for the field level from an upstream I/O module or from the

fieldbus coupler/controller via blade-formed power jumper contacts. It then

provides these potentials to subsequent I/O modules via spring-formed power

jumper contacts.

Pos: 18.1 0 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung /Ei nlei tung /V ersor gu ng/G al vanis ch e Tr en nung Fel d/S yste m @ 3\mod_1233756478750_21.docx @ 27102 @ @ 1

The field voltage and the system voltage are electrically isolated from each other.

Pos: 18.1 1 / Ser ie 7 50 ( WAG O-I/ O-SYST EM)/ Gerät ebesc hreib ung/ Einlei tung/ Versor gung /An ordnung unter Ber üc ksichti gung der Leis tungs konta kte beli ebig @ 3\mod_1233756233468_21.doc x @ 27 099 @ @ 1

With consideration of the power jumper contacts, the individual modules can be

arranged in any combination when configuring the fieldbus node. An arrangement

in groups within the group of potentials is not necessary.

Pos: 19 /D o kume ntatio n allg emein/ Glie derung sele mente /---Seite nwe chsel --- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

16 Device Description WAGO-I/O-SYSTEM 750

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

Pos: 20 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung /Ei nlei tu ng/Ei ns atz ber eich /Ei nsatz ber eic h 7 50- xxxx n ur Koppl er/C ontrol ler aus K ompat ibilit ätslis te @ 4\mod_1242389440265_21.docx @ 33262 @ @ 1

The 753-652 module can be used with the fieldbus couplers and controllers of the

WAGO-I/O-SYSTEM 750 of the specified version or higher listed in the

“Compatibility list” table.

Pos: 21 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Gerät ebesc hrei bung/Ei nlei tung /Eins atzber eich /Kom patibil itäts list en/Ko mpati bilitä tslist e 75x-0 652 @ 15 \mod_1365497370692_21.docx @ 116820 @ @ 1

Table 3: Compatibility List 753-652

Bus System

Fieldbus

Couplers/Controllers

Item No.

Firmware

Revision

Status

PROFINET

Fieldbus coupler

750-370

02

750-375

01

750-377

01

PROFIBUS

Fieldbus coupler

750-333

14

Controller

750-833

14

ETHERNET

Fieldbus coupler

750-341

07

750-342

17

750-352

02

Controller

750-841

18

750-842

18

750-843

02

750-852

09

750-871

07

750-872

03

750-873

03

750-880

02

750-881

02

750-882

01

750-885

09

PFC100 controller

750-810x

05

PFC200 controller

750-820x

01

BA application controller

750-884

09

I/O-IPC

758-870/000-xxx

05

758-874/000-xxx

05

758-875/000-xxx

05

758-876/000-xxx

05

DeviceNet

Fieldbus coupler

750-306

4K

ECO fieldbus coupler

750-346

10

Controller

750-806

10

CANopen

Fieldbus coupler

750-337

19

750-338

19

ECO fieldbus coupler

750-347

08

750-348

08

Controller

750-837

14

750-838

14

WAGO-I/O-SYSTEM 750 Device Description 17

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

Table 3: Compatibility List 753-652

Bus System

Fieldbus

Couplers/Controllers

Item No.

Firmware

Revision

Status

MODBUS

Fieldbus coupler

750-315/300-000

01

750-316/300-000

01

Controller

750-815/300-000

01

750-816/300-000

01

EtherCat

Fieldbus coupler

750-354

03

sercos III

Fieldbus coupler

750-351

04

BACnet

Controller

750-829

07

750-830

03

750-831

07

KNX

Controller

750-849

04

750-889

07

Other fieldbus couplers/controllers on request.

Pos: 22 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

Pos: 23 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 2/A nsi cht - Üb ersc hrif t 2 @ 4 \mod_1240984217343_21.docx @ 31958 @ 2 @ 1

3.1 View

Pos: 24 /S eri e 7 53 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/Hi nw eis z u m Zub ehör tei l 75 3-110 @ 20\mod_1411023611789_21.docx @ 163868 @ @ 1

Depiction of the I/O module with 753-110 Connector!

Information on this pluggable connection pertains to the 753-110 Connector,

which is not included with the I/O module.

Pos: 25 /S eri e 7 53 ( WA GO-I/ O-SYST EM)/ Gerät ebesc hrei bung/A nsic ht/S onder klemm en/Ans icht 75 3-0652 @ 28\mod_1480075682018_21.docx @ 394819 @ @ 1

Figure 1: View

Pos: 26 /S eri e 7 53 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsic ht/A nsic ht – Leg ende mit L eist ungsk ontakt en_ mit Kodi erung , Kabel befest igung und Prüf öffn ungen @ 20 \mod_1411031302199_21.docx @ 163871 @ @ 1

Table 4: Legend for Figure “View”

Pos.

Description

Details See Section

1

Marking possibility with Mini-

WSB

---

2

Status-LEDs

“Device Description” > “Display

Elements”

3

Data contacts

“Device Description” > “Connectors”

4

CAGE CLAMP

®

connectors

“Device Description” > “Connectors”

5

Pull tab

“Mounting” > “I/O Modules with

Pluggable Wiring Level (Series 753)”

6

Coding possibility with coding

fingers

“Mounting” > “Coding”

7

Power jumper contacts

“Device Description” > “Connectors”

8

Test port

---

9

Fixing lug for cable ties

“Mounting” > “I/O Modules with

Pluggable Wiring Level (Series 753)”

Pos: 27 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

Pos: 28 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 2/A nsc hlüs se - Über schr ift 2 @ 4\mod_1240984262656_21.docx @ 31961 @ 2 @ 1

3.2 Connectors

Pos: 29 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsc hlüss e/D ate nko ntakt e/Kl em menbu s - Ü bersc hrift 3 @ 6\mod_1256294684083_21.docx @ 43660 @ 3 @ 1

3.2.1 Data Contacts/Internal Bus

Pos: 30.1 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/A nsc hlüss e/D ate nkon takt e - F eldbu sko ppler /-c ontr oll er, A bbi ld ung und Besc hrei bu ng @ 3\mod_1231771259187_21.docx @ 26002 @ @ 1

Communication between the fieldbus coupler/controller and the I/O modules as

well as the system supply of the I/O modules is carried out via the internal bus. It

is comprised of 6 data contacts, which are available as self-cleaning gold spring

contacts.

Figure 2: Data Contacts

Pos: 30.2 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- und s onsti g e Hin wei se/ Ach tung /A chtu ng: Bus kle mm en nic ht auf G oldfe der kon takt e leg en! @ 7\ mod_1266318463636_21.docx @ 50695 @ @ 1

Do not place the I/O modules on the gold spring contacts!

Do not place the I/O modules on the gold spring contacts in order to avoid soiling

or scratching!

Pos: 30.3 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- und sonstige Hinweise/Achtung/Achtung: ESD - Auf g ute Erd ung der U mg ebu ng ac ht en! @ 7\ mod_1266318538667_21.docx @ 50708 @ @ 1

Ensure that the environment is well grounded!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge. When handling the devices, ensure that the environment

(persons, workplace and packing) is well grounded. Avoid touching conductive

components, e.g. data contacts.

Pos: 31 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750

753-652 Serial Interface RS-232 / RS-485

Manual

Version 2.0.0

Pos: 32 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsc hlüss e/L eist ung skont akt e/F eld vers orgu ng - Üb ersc hrift 3 @ 6\ mod_1256294692864_21.docx @ 43664 @ 3 @ 1

3.2.2 Power Jumper Contacts/Field Supply

Pos: 33.1 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd so nsti g e Hin weis e/ Vorsi cht /V orsi cht : Ver let zung sge fa hr dur c h sc harf kan tig e M ess erko nta kte! @ 6\ mod_1256193279401_21.docx @ 43414 @ @ 1

Risk of injury due to sharp-edged blade contacts!

The blade contacts are sharp-edged. Handle the I/O module carefully to prevent

injury.

Pos: 33.2 /Serie 750 (WAGO-I/O-SYST EM)/ Ger ätebesc hrei bung/A nschl üsse /Leist ung skont akte 2 LK (M esser /Feder ) - Einl eitu ng @ 1 5\mod_1371721641099_21.docx @ 123714 @ @ 1

The I/O module 753-652 has 2 self-cleaning power jumper contacts that supply

and transmit power for the field side. The contacts on the left side of the I/O

module are designed as blade contacts and those on the right side as spring

contacts.

Pos: 33.3 /Serie 753 (WAGO-I/O-SYST EM) /Ger äte bes chr eibu ng/ Ansc hl üsse /L eist ung sko nta kte/F eld vers or gu ng 2 LK (M es ser/F e der) - Abbildung @ 17\mod_1381924880242_21.docx @ 134239 @ @ 1

Figure 3: Power Jumper Contacts

Pos: 33.4 /Serie 750 (WAGO-I/O-SYST EM)/ Ger ätebesc hrei bung/A nschl üsse /Leist ung skont akte 2 LK (M esser /Feder ) - Leg end e @ 1 5\mod_1371721352500_21.docx @ 123710 @ @ 1

Table 5: Legend for Figure “Power Jumper Contacts”

Contact

Type

Function

1

Spring contact

Potential transmission (U

v

) for field supply

2

Spring contact

Potential transmission (0 V) for field supply

3

Blade contact

Potential feed-in (0 V) for field supply

4

Blade contact

Potential feed-in (U

v

) for field supply

Pos: 33.5 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd sonsti ge Hin weis e/Acht ung/A chtu ng: Ma ximaler Strom L eistung skon takt e 10 A @ 3\mod_1226499143500_21.docx @ 25029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded.

If exceeded, insert an additional supply module.

Pos: 33.6 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd so nsti g e Hin weis e/H inw eis/H i nwei s: Pote nti alei ns peis ekl emme für Erd e ei nse tze n! ( kei ne L K f ür E rde) @ 3 \mod_1226499037468_21.docx @ 25023 @ @ 1

Page is loading ...

WAGO RS-232/RS-485 Serial Interface User manual

WAGO RS-232/RS-485 Serial Interface User manual

Related papers

Other documents