Reznor ADFH Operating instructions

Brand: Reznor

Model: ADFH

Category: Car kits

Type: Operating instructions

This manual is also suitable for

CP-AG30/31/32/35&AG33 Amplier Kits, P/N268300 R1, Page 1

Form CP-AG30/31/32/35&AG33 Amplier Kits (Version A)

Obsoletes CP-AG30/31/32/35&AG33 Amplier Kits

Replacement Parts

Applies to: Reznor Direct-Fired Equipment

with Electronic Modulation

Replacement Kit P/N 268301 for Maxitrol Amplier in Electronic Modulation

Option AG30, AG31, AG32, or AG35 AND Replacement Kit P/N 268302 for

Maxitrol Amplier in Electronic Modulation Option AG33

These replacement ampliers function the same as the original, but when replacing an

older amplier, there are different installation and wiring requirements.

Application and

Components

Kit Use this kit to replace: Kit Components

P/N

268301

Amplier P/N 148590, Model A1014U or A1014L,

or amplier P/N 86976, Model A1014, in Electronic

Modulation Option AG30, AG31, AG32, or AG35.

Amplier, P/N 148590, A1014R

(10) Wire Terminals, P/N 1350

P/N

268302

Amplier P/N 86989, 119616, 157915, or 194159

in Electronic Modulation Option AG33.

Amplier, P/N 268274, A1044U

(2) Screws, P/N 38529

(10) Wire Terminals, P/N 142860

Instructions

1. Turn off the gas and disconnect the power.

2. Locate the amplier being replaced. Mark and disconnect the wires from the

amplier. If installing Kit P/N 268302, make note of the temperature settings.

Remove the amplier.

3. Follow the appropriate instructions to install the replacement amplier:

If installing Kit P/N 268301 which replaces amplier Model A1014U or A1014L

(also P/N 148590) and amplier Model A1014, refer to DIAGRAM 1 below.

a) Attach the replacement amplier with the screws supplied.

b) Locate all of the disconnected amplier wires (Step 2). Attach the “fork”

terminals in the kit to all wires (replacing any existing terminals). Refer to

replacement amplier section of DIAGRAM 1 and connect the wires.

c) On the upper left corner of the replacement amplier, nd two recessed dip

switches. Set the dips switches to the positions shown in DIAGRAM 1.

P/N

148590,

Maxitrol

Model

A1014R

P/N 268274,

Maxitrol

Model

A1044U

(cover

removed)

TEMP SELECTOR

TS114 TEMP. SENSOR

2 1

8 1

A1014R AMPLIFIER

TD114

M/R VALVE

6 7

INTREGAL

NONE

REMOTE

LFSTSELECTOR

10 SEC.

TEMP SELECTOR

TS114 TEMP. SENSOR

2 1

8 1

TD114

M/R VALVE

6 7

P/N 148590, A1014U or A1014L

P/N 86976, A1014

REPLACEMENT

Amplifier,

P/N 148590,

A1014R

Dip Switches

DIAGRAM 1 - applies to

replacement amplier in

electronic modulation

Options AG30, AG31,

AG32, and AG35

If installing Kit P/N 268302 which replaces amplier P/N 86989, 119616, 157915,

or 194159, refer to DIAGRAM 2, page 2.

a) The temperature range on the amplier dials must match the temperature

range of the sensor. The Model A1044U replacement amplier (P/N 268274) is

Section applies only

to Kit P/N 268301

NOTE: When Step 3 is

completed, continue to

Steps 4 & 5 on page 2.

Section applies only

to Kit P/N 268302



CP-AG30/31/32/35&AG33 Amplier Kits, P/N268300, Page 2

www.ReznorHVAC.com; (800) 695-1901

Trademark Notes: Reznor

is registered in at least the United States.

All other trademarks are the property of their respective owners.

04/14 (Serial No. Date Code BNE) Form CP-AG30/31/32/35&AG33 Amplier Kits (Ver A)

DIAGRAM 2 - applies to

replacement amplier in

electronic modulation

Option AG33

TEMP SELECTOR

8 4

5 1 32

T244

M/R VALVE

7 9

A1044U AMPLIFIER

TS144E TEMP. SENSOR

(SET JUMPER

@ 20 SEC)

REPLACEMENT

Amplifier,

Model A1044U,

P/N 268274

TEMP SELECTOR

8 4

5 1 32

T244

M/R VALVE

7 9

A1044CL AMPLIFIER (USED ON ADFH ONLY) or A1044EL AMPLIFIER

TS144C TEMP. SENSOR - USED ON ADFH ONLY

TS144E TEMP. SENSOR

A1044EL or A1044CL Amplifier

MR VALVE

R R

V S

APS

IGNITION SYSTEM

GND

IGN

FLAME

SENSOR

HOT SURFACE

IGNITOR

BRBR

SELECTRASTAT

TS144E TEMP SENSOR (PN 119617)

5 1 3

AMPLIFIER A1044E (PN 119616) or A1044 (P/N 86989)

2 6 7 98

MV2

A1044 or A1044E Amplifier

“J5”

Instructions - Step 3 (cont’d)

4. When installation is complete, close the cabinet. Turn on the electric; turn on the

gas; and check for proper operation.

5. Keep this form for future reference.

adaptable to work with sensor

Models TS144, TS144C, and

TS144E. Check the model number

displayed on the sensor and follow

the instructions that apply.

Sensor TS144 - No change

required.

Sensor TS144C - Change the “Min”

label to 20° - 60°.

Sensor TS144E - Change the “Min”

label to 20° - 60° and the “Max”

label to 60° - 120°.

Find the labels included with the

amplier and select the one or two

that will be needed. Do not remove

the existing dial label but be sure

that it is clean and dry. Remove

the adhesive backing and carefully

slide the replacement label under

the temperature pointer. Line up

with the center leg and adhere the

label.

Temperature Dials on Model

A1044U Amplier

b) Position the mounting rail for

the new amplier over the same

area where the old amplier was

mounted. Mark the two mounting

holes. Drill 7/64” pilot holes. Attach

the rail using the screws provided.

Carefully attach the amplier to the

mounting rail.

c) Locate all of the disconnected

amplier wires (Step 2) and cut

off their terminals. Replace with

the insulated terminals in the kit.

Refer to replacement amplier in

DIAGRAM 2 and connect the wires.

d) In the center on the lower

portion of the amplier, locate

“J5”. Move the jumper to the 20

second position as shown on the

replacement amplier in

DIAGRAM 2.

Set the dials to the temperature

settings of the removed amplier.

Install the amplier cover.

Section applies only to Kit P/N 268302 (cont’d)

Steps 4 & 5 apply to

ALL Replacements

- both Kit P/N 268301

and Kit P/N 268302



Reznor ADFH Operating instructions

Brand: Reznor

Model: ADFH

Category: Car kits

Type: Operating instructions

This manual is also suitable for

Download PDF

report

Reznor ADFH Operating instructions

This manual is also suitable for

Reznor ADFH Operating instructions

Related papers

Other documents