Adjustable Radical Face
Protector Owners Guide
Model
40VIZI2 and 40VIZI4
40VIZI2-M0_072016
Mask, Lens Care, Lens Replacement and Headgear Assembly Instructions
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
!
© July 2016
2
HELMET FIT INSTRUCTIONS
9 Point high quality headgear with 4 adjustment locations.
• For the top of the head adjustment; make the adjustment by aligning the strap to its
proper place depending on the size of your head.
• For the helmet to t tight PUSH IN and TURN the rear adjustment wheel on the
back of the headgear.
• FOR FORWARD AND AFT ADJUSTMENTS - Loosen the headgear outer locking
nuts and realign the headgear screws to the proper slots located INSIDE the
Welding Helmet. Be sure the headgear is adjusted in the same position on both
sides.
SAFETY AND GENERAL INFORMATION
• Failure to comply with the enclosed may result in injury or blindness.
• WARNING: Risk of Ultraviolet Rays. Flying Particles. Wear Safety Goggles (User and
Bystanders).
• Materials which come into contact with the wearer’s skin could possibly cause allergic reactions
to susceptible individuals.
• Scratched or damaged oculars (lenses) should be replaced.
• This is not a Paintball mask! It is a welding helmet.
• Toughened mineral lter oculars shall only be used in conjunction with a suitable backing ocular.
!
WARNING
NOTICE:
For your SAFETY - PLEASE read and follow all of these instructions exactly. If you have problems
understanding these instructions or have
questions, please call 1-866-783-3223.
Caution! Read and follow these instructions EXACTLY for care and cleaning of the lenses. These
lenses are made from the highest quality polycarbonate known to man WITH a Military Grade Anti
Scratch Coating AND the World’s BEST Anti Fog Coating on the inside.
Remember, there is NO SUCH thing as a permanent Anti Fog coating. ALL anti fog coatings eventu-
ally come off. If you clean the lenses improperly, you’ll increase the rate of deterioration or possibly
wipe off the coatings. So, PLEASE follow these instructions every time you clean the non-ADF lens.
LENS CARE, INSTALLATION and REMOVAL INSTRUCTIONS
(ADF LENS)
To Clean: Remove ADF Filter from ADF Lens holder by removing the 4 screws off the
back ADF cover plate.
• Clean ADF Lens Holder with water only. Rinse ADF Lens holder under running
water, shake off residue and dry off with a Micro Fiber or lint free soft cloth.
INSTALLATION and REMOVAL of ADF, FRONT PROTECTIVE CLEAR
COVER LENS and REAR ADF PROTECTIVE COVER LENS
1. Remove the four nger screws and remove the REAR ADF Holder Plate to the Outer Lens.
2. Take out the old ADF Lens
3. When you replace the clear protective outer ADF Lens cover, squeeze the two tabs on the inside
and press outward. The clear protective lens will pop out of the Outer Lens. Gently snap in a new one.
4. Replace the old ADF Filter with a new ADF that matches the ADF Holder Lens
Shade as shown on the outside of the ADF Holder Lens.
5. Place the new ADF Filter with the Solar Panels facing the welding arc.
6. Place the rear ADF Holder over the ADF and install nger screws.
7. Do NOT over tighten nger screws.
3
USING the ADJUSTABLE ADF
Our advanced optical detection system monitors your welding process to ensure that your lter
remains in the dark state in a wide range of arc-welding applications. Protection from harmful
ultra-violet / infrared radiation is always present whether in the light or dark state. Your new lter
energizes automatically as soon as the arc is struck. All models are solar powered so there are no
on / off switches. The solar cell within the mask also recharges the onboard battery.
Note: The above settings are meant to illustrate which welding applications are suggested
for each congurable mode. Applications vary greatly so please experiment with the many
available setting combinations in order to nd the best combination of shade level, sensitivity
and delay for your personal comfort and performance efciency.
SELECTING THE SHADING LEVEL (Shade Control Knob)
The shading level can be set manually from 9 - 13. Consult the above table of
recommended shading for the correct shading level for your work. Select a shading level
by turning the shading dial until the arrow is pointing at the level you require.
SETTING THE DELAY/SWITCHING TIME (Delay Control Knob)
The delay/switching time (this means at that moment at which welding begins, the
lter changes from light to dark) is set using the rotary knob. In the case of the “short”
setting this is approx. 1/20000 of a second, “long“ is approx. 6/10 of a second.
4
SETTING the SENSITIVITY (SENSITIVITY CONTROL KNOB)
The rotary knob can be used to adjust the sensitivity to suit the welding process.
GRIND MODE ADJUSTMENT (GRIND CONTROL KNOB)
Turn grind mode switch on.
MORE INFORMATION
• This information is intended for ALL Save Phace RFP 1 (Radical Face Protector) models.
• This RFP is intended as a Welding Helmet and Grinding Mask as per ANSI and CE standards
for low impact protectors.
• All parts on the RFP are replaceable. Please contact your local Save Phace Retailer/Distributor
for these parts.
• For accessories, including magnication lenses and other cool accessories, please contact your
local Save Phace Retailer/Distributor or log onto www.SavePhace.com
• All Save Phace ADF lenses have a 2 year warranty. You must register your product to obtain
warranted replacement products.
• If you take care of this RFP it should last you a lifetime!
• CE EN 175:1997 –F means this product passed all of the requirements as stated by the European
Counsel. The CE EN 175:1997 means this particular EN 175 was adopted in 1997. The –F means
it passed the low impact standards.
• When transporting your product we recommend placing it in a nice Helmet Bag that comes with
your purchase.
• Replacement parts on the RFP are recommended when broken, damaged or cracked. Otherwise,
replace the RFP lenses are recommended once per year.
• This Product meets or exceeds ANSI Z87.1 Standards.
• This Product meets or exceeds CSA Standards.
NOTES
• When not using your RFP or RFP ADF lens, we recommend keeping them in a bag away from
harmful chemicals or Radical heat.
• DO NOT USE ANY lens Cleaner, Windex®, Alcohol or Gasoline. Use of any of these or similar
products will damage the coatings and lens.
• ALWAYS use OSHA/CE approved safety glasses when welding.
5
PQ
T
U
V
V
U
T
S
R
1. Right adjustable angle regulator
2. Angle adjusting shaft
3. Headgear set
4. Left adjustable angle regulator
5. Inside square washer
6. Outside square washer
7. Headband adjusting nut
• Headgear has left hand and right hand parts and tightens counter clockwise.
• If after assembly and installation into the helmet you cannot feel a strong
ratcheting (click, click, click) of the adjusting knobs, you have installed some or
all of the right and left hand parts on the wrong side.
HEADGEAR ASSEMBLY INSTRUCTIONS
40VIZI2
Auto Adjustable Specs:
ADF Size – 4.33″ x 3.54″
ADF Viewing Area – 3.82″ x 1.85″
Arc Sensors – 4
Light State – Shade 4
Shades – Shade 9-13
Time From Dark To Light – .1-.9 Adjustable
ADF Classication – 1/1/1/2
Grind Function – Yes
Grind Warning Indicator – Yes
Low Battery Warning Indicator – Yes
Sensitivity Internal Adjusted – Yes
Delay Internal Adjusted – Yes
Power On/Off – Fully Automatic
Power Supply – Solar Cells +
Lithium Ion Battery
Switching Time (ms) – .23 ms
Weight (oz) – 13 oz
Operating Temperature – 14° F to 149° F
40VIZI4
Auto Adjustable Specs:
ADF Size – 4.33″ x 3.54″
ADF Viewing Area – 3.82″ x 1.85″
Arc Sensors – 2
Light State – Shade 4
Shades – Shade 9-13
Time From Dark To Light – .1-.9 Adjustable
ADF Classication – 1/1/1/2
Grind Function – Yes
Grind Warning Indicator – Yes
Low Battery Warning Indicator – Yes
Sensitivity Internal Adjusted – Yes
Delay Internal Adjusted – Yes
Power On/Off – Fully Automatic
Power Supply – Solar Cells +
Lithium Ion Battery
Switching Time (ms) – .23 ms
Weight (oz) – 13 oz
Operating Temperature – 14° F to 149° F
6
REPLACEMENT PARTS
Not all components are replacement items, but are illustrated as a convenient reference of location
and position in the assembly sequence. When ordering parts, please give the Model number and
parts description. Call or write for current pricing:
SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A.
E-Mail: [email protected] Tel: (866) 783-3223 Fax: (816) 891-6599
Item
Part Number
Description Qty.
40VIZI2 40VIZI4
1N/A Mask 1
23011667 Lens Key and Anchor
(Left & Right)
2
33012053 Screw 4
43011568 3011575 ADF 1
53011391 Back Cover 1
63011582 Protective Lens 1
73011599 Front Cover Lens 1
83011407 ADF Holder 1
93011544 Halo (Not Shown) 1
1
2
3
4
5
6
7
8
7
NOTES:
8
ONE YEAR LIMITED WARRANTY
SavePhace products undergo a strict quality control inspection for workmanship, function, and
safety before leaving the factory. From the date of purchase, SavePhace will warranty or
repair it's products for: one (1) year on its helmet and two (2) years on its the ADF against defects
in parts and workmanship. We have a general warranty claim form along with potential request of
proof of purchase.
In the unlikely event a problem is experienced with any of our products, a return merchandise
authorization (RMA) number must be obtained by contacting us toll-free at 866-783-3223. Each
product to be returned must have the item number, description of the problem and proof of purchase.
All returns must have a RMA number marked clearly on the outside of the shipping box, and printed
RMA form enclosed inside the box. Only SavePhace can determine if product can be repaired or
must be replaced.
Except where such limitations and exclusions are specically prohibited by applicable law, (1) THE
CONSUMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT
OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE. (2) SavePhace. SHALL NOT BE
LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER. (3)
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO
ONE YEAR, OTHERWISE THE REPAIR, REPLACEMENT OR REFUND AS PROVIDED UNDER
THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER,
AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. (4) ANY
MODIFICATION, ALTERATION, ABUSE, UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN
VOIDS THIS WARRANTY AND IS NOT COVERED BY THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation
may not apply to you. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you. This warranty
gives you specic legal rights, and you may also have other rights, which vary from state to state.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Lincoln Electric VIKING 2450D Operating instructions
-
-
Lincoln Electric VIKING 1740 Operating instructions
-
-
-
-
-
Lincoln Electric VIKING 3350 Operating instructions
-
Lincoln Electric VIKING 700G Operating instructions
-