Ditek DTK-PVP27BP Installation guide

  • Hello! I've reviewed the installation instructions for the DITEK Surge Protective Device DTK-PVP27BP. This document outlines the proper installation procedures for this device, which is designed to protect sensitive electronics connected to service panels, fire panels, or directly to the electronic device. It also details how to connect video and power using UTP to BNC conversions for analog fixed cameras. I'm ready to answer any questions you have about it.
  • What kind of circuits should this surge protector be used on?
    What is the minimum recommended wire length between the surge protector and the equipment it's protecting?
    What is the maximum ground resistance allowed for the surge protector?
Doc # INT-100077-001
Part No. 191134 Rev. 3
INSTALL INSTRUCTIONS
DTK-PVP27BP
DITEK Technical Support Available 24/7
1-888-472-6100 www.ditekcorp.com
DITEK Corporation
ONE DITEK CENTER
1720 Starkey Road
Largo, FL 33771
INSTALLATION
This Surge Protective Device (SPD) is a high performance device, designed to provide protection
for sensitive electronic loads connected to service panels, fire panels, or where the SPD is directly
connected to the electronic device. Maximum protection will only be achieved if the SPD is properly
installed. Please read and follow the installation instructions carefully.
NOTICE: This SPD should be installed and grounded, by a licensed contractor, per the applicable
requirements of the NEC. These devices are only to be employed on communication loop circuits which
have been isolated from the Public Switched Telephone Network.
APPLICATION
Low voltage power and video connections using UTP to BNC conversions for analog Fixed cameras.
This device is intended for indoor use or intended for outdoor use within an enclosure which has been
evaluated for the applicable environment.
Drawn By: B. Aycock 10-18-17
Approved By: R. Mitchell 10-23-17
WIRING INSTRUCTIONS:
Caution
: Measure all voltages to insure applied voltage does not exceed the voltage rating of the
module. Improper installation voids the warranty.
Pre Install Actions:
This unit must be connected in series with the field wiring and the equipment to be protected.
1. Check the power and video signals before installation to verify correct operation.
2. Power down and disconnect the circuits this device will connect to before beginning installation.
3. Securely mount this unit between the field wiring and the equipment to be protected. Use the double
sided tape or two #8 screws (provided).
Note: Allow the surge protector reaction time by providing 3-6 wire feet of conductor length between the
DTK-PVPBP and the equipment to be protected.
Video Protection:
1. Connect the unprotected twisted pair video feed from the field to the VIDEO IN terminals.
2. Connect a minimum 3 foot BNC patch cord from the VIDEO OUT connector to the video input of the
equipment to be protected.
Power Protection:
1. Connect the input wiring from the 12V/24V power supply to the UNPROTECTED IN terminals
marked 12V/24V PWR.
2. Connect a minimum of 3 feet of supply wires from the PROTECTED OUT terminals marked
12V/24V PWR to the inputs of the equipment to be protected.
Ground Connection:
Connect a minimum #14 AWG wire from the ground connector to the common earth ground. Always
have one common ground per system to eliminate the possibility of a differential in ground potentials.
Ground Resistance Rule:
Max ground resistance is 25 Ohms, 5 Ohms or less is optimum.
This cannot be an assumed value and must be measured to assure proper grounding.
Post Install Actions:
After all connections have been made and no hazards exist, restore power.
Check the power and video signals after installation to ensure proper install and no signal distortion.
For further information or technical support, please call 1-888-472-6100.
INSTALL INSTRUCTIONS
DTK-PVP27BP
DITEK Technical Support Available 24/7
1-888-472-6100 www.ditekcorp.com
DITEK Corporation
ONE DITEK CENTER
1720 Starkey Road
Largo, FL 33771
INSTALLATION
Illustrations Page
Doc # INT-100077-001
Part No. 191134 Rev. 3
Drawn By: B. Aycock 10-18-17
Approved By: R. Mitchell 10-23-17
GROUND WIRE
14 AWG MIN.
-
+
INPUT VIDEO WIRING
12/24 VOLT PWR
EQUIPMENT WIRING
ALLOW 3’ FT MIN.
LENGTH
CAMERA END
ALLOW 3’ FT MIN.
LENGTH
EQUIPMENT POWER WIRE
TO DVR/HEAD END
GROUND WIRE
14AWG MIN.
VIDEO EQUIP. WIRING -
+
INPUT VIDEO WIRING
ALLOW 3’ MIN
LENGTH
12/24 VOLT POWER
POWER
SUPPLY
ALLOW 3’ FT MIN.
LENGTH
EQUIPMENT POWER WIRE
BNC
DTK-PVP27BP
U
N
P
R
O
T
E
C
T
E
D
DITEK
UTP
VIDEO
GND
OUT IN
P
R
O
T
E
C
T
E
D
24V PWR
24V PWR
OUT IN
BNC
DTK-PVP27BP
U
N
P
R
O
T
E
C
T
E
D
DITEK
UTP
VIDEO
GND
OUT IN
P
R
O
T
E
C
T
E
D
24V PWR
24V PWR
OUT IN
/