Intel IB850 User manual

IB850

Socket 478 Pentium 4

Intel 875P Chipset

Full Size CPU Card

USER’S MANUAL

Version 1.0

ii IB850 User’s Manual

Acknowledgments

Award is a registered trademark of Award Software International,

Inc.

PS/2 is a trademark of International Business Machines

Corporation.

Intel and Pentium 4 are registered trademarks of Intel Corporation.

Microsoft Windows is a registered trademark of Microsoft

Corporation.

Winbond is a registered trademark of Winbond Electronics

Corporation.

All other product names or trademarks are properties of their

respective owners.

IB850 User’s Manual iii

Table of Contents

Introduction..............................................................1

Checklist........................................................................1

Product Description ........................................................2

Specifications .................................................................3

Board Dimensions...........................................................5

Installations..............................................................7

Installing the CPU...........................................................8

ATX Power Installation...................................................9

Installing the Memory......................................................9

Setting the Jumpers.......................................................10

Connectors on IB850 ....................................................18

BIOS Setup..............................................................33

Drivers Installation............................................56

Intel 875P Chipset Software Intallation Utility.................57

Realtek AC97 Codec Audio Driver Installation...............60

Intel PRO LAN Drivers Installation...............................61

ATI M7 VGA Driver Installation...................................62

ATI M9/M10 VGA Driver Installation ...........................64

iv IB850 User’s Manual

This page is intentionally left blank.

INTRODUCTION

IB850 User’s Manual 1

Introduction

Checklist

Your IB850 Pentium 4 CPU card package should include the items listed

below:

• The IB850 CPU Card

• This User’s Manual

• 1 IDE Ribbon Cable

• 1 Floppy Ribbon Connector

• SATA Power Cord

• SATA Cable

• 2 Serial Port Ribbon Cable and 1 Parallel Port Attached to a

Mounting Bracket

• 1 Y-Cable supporting a PS/2 Keyboard and a PS/2 Mouse

• 1 CD containing the following:

• Chipset Drivers

• Flash Memory Utility

• Optional audio cable with bracket (Audio8K)

• Optional USB cable with bracket (USB2K-4)

• Optional Secondary CRT VGA cable with bracket (VGA4K, for use

with IBA110)

• Optional TMDS cable with bracket (ID120P, for use with IBA110)

• Optional MicroAGP cards (IBA110)

INSTALLATIONS

2 IB850 User’s Manual

Product Description

The IB850 Pentium 4 CPU card incorporates the Intel 875P chipset that can

utilize a single PGA478 processor of up to 3.2GHz or higher and supports

FSB frequency of 400/533/800Mhz (100Mhz, 133Mhz, and 200Mhz HCLK

respectively).

The 875P chipset comes with a Memory Controller Hub (MCH) designed

for use with the Pentium 4 processor with 512-KB L2 cache on 0.13 micron

process. The MCH component provides the CPU interface, DDR

interface, Hub Interface, and AGP8X graphics interface.

Aside from CRT support, the VGA function feature a Micro AGP slot for

optional daughter cards:

IBA110: with ATI M7CSP32, M9CSP64 / M10CSP64 chipset,

64MB/32MB frame buffer and supports dual channel LVDS interface,

TMDS and CRT2 display function.

Two DDR memory sockets support up to 2GB DDR 266/333/400

ECC/non-ECC SDRAM.

The board also has an Intel 82551 10/100MB fast Ethernet LAN and

optional Intel 82547EI Gigabit LAN as secondary LAN.

Other advanced features include two Serial ATA ports, four USB 2.0

ports, IrDA interface and audio function.

INTRODUCTION

IB850 User’s Manual 3

Specifications

Product Name IB850

Form Factor PICMG (full size CPU card)

CPU Type Socket 478 (Intel Pentium 4)

CPU Voltage 0.8375V~1.6V (VRD 10)

System Speed 2.0G~3.2GHz

CPU Frequency 400 MHz/533MHz/800MHz

Green /APM APM1.2

CPU Socket Socket 478

Chipset

Intel 875P Chipset

MCH: 82875P 932 pin FC-BGA

ICH5R: 82801ER 460 pin MBGA

BIOS Award BIOS, support ACPI Function

Cache 128K/256K/512K Level 2 (CPU integrated)

VGA MicroAGP daughter card w/ ATI Mobility M7/ M9 / M10

graphics controller, embedded 32/64MB Frame buffer

(DDR), AGP 4X, support CRT, LVDS, TV-out / 2nd CRT.

Primary LAN Intel 82551QM LAN controller (10/100Mb)

Secondary LAN Intel 82547EI (10/100/1000Mb) Gigabit LAN (optional)

Audio ICH5R Built-in Sound controller + AC97 Codec ALC650, 2x6

12 pin header (Line-out, Line-in, MIC.). Supports 5.1

channels.

Memory type

2 x DDR 2.5V PC266/333/400 DDR SDRAM (support ECC

Function) DIMM Module, Max. capacity - 2GB

LPC I/O Winbond 83627HF: IrDAx1 Parallel x1, COM1 (RS-232),

COM2 (RS-232/RS422/RS485), FDC 2.88MB (3 Mode

Support), Hardware monitoring

RTC/CMOS ICH5R Built-in

Battery Lithium Battery

PS2 KB/Mouse Controller built in Winbond 83627HF

Local bus IDE ICH5R built in, IDE1, IDE2 (Ultra DMA 33/66/100)

Serial ATA 2 ports

PCI to ISA

Bridge

ITE 8888

ISA High drive Supported by SN74ABT16245

USB 4 ports, USB 2.0

IrDA Pin header

Disk On Chip Supports up to 288MB capacity

Watchdog

Timer

Yes (256 segments: 0,1,2,...255 sec/min)

Expansion slots MicroAGP VGA socket for IBA110

D-type

connector

PS/2 keyboard/mouse, VGA (CRT), RJ-45 x 2

Power

ATX 12V

INSTALLATIONS

4 IB850 User’s Manual

Connector

System

Voltages

+5V, +12V, -12V, 5VSB

Board Size 122 x 338 mm

Other Features Modem Wakeup, LAN Wakeup

INTRODUCTION

IB850 User’s Manual 5

Board Dimensions

0.2" [5.08]

9.762" [247.95]

6.087" [154.61]

6.712" [170.48]

4.6" [116.84]

4.362" [110.79]

3.792" [96.32]

3.196" [81.18]

0.856" [21.74]

4.8" [121.92]

0" [0.00]

9.372" [238.05]

12.372" [314.25]

13.117" [333.17]

13.317" [338.25]

O0.16" [O4.06]

3.133" [79.58]

2.562" [65.07]

3.546" [90.07]

3.054" [77.57]

3.95" [100.33]

4.8" [121.92]

1.948" [49.48]

0" [0.00]

2.124" [53.95]

1.454" [36.93]

0.7" [17.78]

0.865" [21.97]

0.2" [5.08]

0.987" [25.07]

0" [0.00]

O0.16" [O4.06]

INSTALLATIONS

6 IB850 User’s Manual

INSTALLATIONS

IB850 User’s Manual 7

Installations

This section provides information on how to use the jumpers and

connectors on the IB850 in order to set up a workable system. The topics

covered are:

Installing the CPU...........................................................8

ATX Power Installation...................................................9

Installing the Memory......................................................9

Setting the Jumpers.......................................................10

Connectors on IB850 ....................................................18

INSTALLATIONS

8 IB850 User’s Manual

Installing the CPU

The IB850 CPU card supports a Socket 478 processor socket for Intel

Pentium 4 processors.

The Socket 478 processor socket comes with a lever to secure the

processor. Raise this lever to about a 90° angle to allow the insertion of the

processor. Place the processor into the socket by making sure the notch

on the corner of the CPU corresponds with the notch on the inside of the

socket. Once the processor has slide into the socket, return the lever to

the lock position. Refer to the figures below.

After you have installed the processor into the socket, check if the

jumpers for the CPU type and speed are correct.

NOTE:

Ensure that the CPU heat sink and the CPU top surface are in

total contact to av

oid CPU overheating problem that would

cause your system to hang or be unstable.

INSTALLATIONS

IB850 User’s Manual 9

ATX Power Installation

The system power is provided to the CPU card with the CN1 and J7 ATX

power connectors. Please note that the J7 external ATX power connector

should be connected to the backplane for IB850 to function. J7 is a 3-pin

power connector. CN1 is a 4-pin 12V power connector. CN1 is to be

connected to the ATX power supply.

Installing the Memory

The IB850 CPU card supports two DDR memory sockets for a maximum

total memory of 2GB in DDR memory type. You can install unbuffered

DDR DIMMs with ECC function. It supports DDR266 when installed with

CPUs that have clock speeds of 400MHz. It supports DDR266/333 when

installed with CPUs that have clock speeds of 533MHz. It supports

DDR266/333/400 when installed with CPUs that have clock speeds of

800MHz. The board provides dual channel functionality for its DIMM

slots. DIMM1 is for one channel and DIMM2 is for the other channel.

Enabling dual channels can increase data access rates.

Basically, the system memory interface has the following features:

Supports two 64-bit wide DDR data channels

Available bandwidth up to 3.2GB/s (DDR400) for single-channel

mode and 6.4GB/s (DDR400) in dual-channel mode.

Supports ECC/ non-ECC DIMMs.

Supports 128MB, 256MB, 512MB DDR technologies.

Supports only x8, x16, DDR devices with four banks

Registered DIMMs not supported

Supports opportunistic refresh

Up to 16 simultaneously open pages (four per row, four rows

maximum)

INSTALLATIONS

10 IB850 User’s Manual

Setting the Jumpers

Jumpers are used on IB850 to select various settings and features

according to your needs and applications. Contact your supplier if you

have doubts about the best configuration for your needs. The following

lists the connectors on IB850 and their respective functions.

Jumper Locations on IB850....................................................................11

JP1: Clear CMOS Contents ....................................................................12

JP2, JP3, JP4: RS232/422/485 (COM2) Selection.................................12

JP6: 82551 10/100Mb LAN Enable/Disable..........................................12

JP7: DiskOnChip Address Select..........................................................13

JP9: AT/ATX Power Supply Select......................................................13

Jumper and Connectors on IBA110......................................................14

J1: TMDS Panel Connector....................................................................14

J2: CRT2 / TV-Out Connector................................................................14

J3: Panel Inverter Power Connector......................................................15

J4: VGA Chipset Fan Power Connector...............................................15

J5, J6: LVDS Connectors (2nd channel, 1st channel).........................15

JP1: LVDS Panel Power Select...............................................................15

SW1: LVDS Resolution Select...............................................................17

INSTALLATIONS

IB850 User’s Manual 11

Jumper Locations on IB850

CN1

J1

DIMM1

J3

BZ1

DIMM2

JP8

J2

IDE1

FDD1

CN3

CN2

J8

J7

J9

AGP1

BAT1

IDE2

J6

J14

J4

J13

J11

J15

J5

J12

J19

RT2

JP7

J20 J21

Jumper Locations on IB850

JP1: Clear CMOS Contents

JP2, JP3, JP4: RS232/422/485

(COM2) Selection

JP6: 82551 10/100Mb LAN

Enable/Disable

JP7: DiskOnChip Address Select

JP9: AT/ATX Power Supply Select

INSTALLATIONS

12 IB850 User’s Manual

JP1: Clear CMOS Contents

Use JP1, a 3-pin header, to clear the CMOS contents. Note that the

ATX-power connector should be disconnected from the CPU card before

clearing CMOS.

JP1 Setting Function

Pin 1-2

Short/Closed

Normal

Pin 2-3

Short/Closed

Clear CMOS

JP2, JP3, JP4: RS232/422/485 (COM2) Selection

J4, COM1 is fixed for RS-232 use only.

J5, COM2 is selectable for RS232, RS-422 and RS-485.

The following table describes the jumper settings for COM2 selection.

COM2

Function

RS-232 RS-422 RS-485

Jumper

Setting

(pin closed)

JP2:

1-2

JP3:

3-5 & 4-6

JP4:

3-5 & 4-6

JP2:

3-4

JP3:

1-3 & 2-4

JP4:

1-3 & 2-4

JP2:

5-6

JP3:

1-3 & 2-4

JP4:

1-3 & 2-4

JP6: 82551 10/100Mb LAN Enable/Disable

JP6 Function

Enable LAN

Disable LAN

INSTALLATIONS

IB850 User’s Manual 13

JP7: DiskOnChip Address Select

JP7 Address

D0000-D7FFF

D8000-D9FFF (default)

JP9: AT/ATX Power Supply Select

JP9 Function

ATX power supply

AT power supply

INSTALLATIONS

14 IB850 User’s Manual

Jumper and Connectors on IBA110

J1: TMDS Panel Connector

TMDS stands Transition Minimized Differential Signaling.

Signal Name Pin # Pin # Signal Name

TX1P 1 11 TX2P

TXIN 2 12 TX2N

GND 3 13 GND

GND 4 14 GND

TXCP 5 15 TX0P

TXCN 6 16 TX0N

GND 7 17 NC

+5v 8 18 NC

HTPG 9 19 DDCDATA

J1

NC 10 20 DDCCLK

J2: CRT2 / TV-Out Connector

This connector is used for a second CRT monitor or use with a TV output device.

Signal Name Pin #

Pin #

Signal Name

Red / C 1 9 +5V

Green / Y 2 10 Ground

Blue / COMP 3 11 N. C.

N.C. 4 12 CRT2 DDCDAT

Ground 5 13 HSYNC

Ground 6 14 VSYNC

Ground 7 15 CRT2 DDCCLK

J2

Ground 8 16 N.C.

J1: TMDS Panel Connector

J2: CRT2 / TV-Out Connector

J3: Panel Inverter Power Connector

J4: VGA Chipset Fan Power Connector

J5, J6: LVDS Connectors (2nd channel, 1st

channel)

JP1: LVDS Panel Power Select

SW1: LVDS Resolution Select

INSTALLATIONS

IB850 User’s Manual 15

J3: Panel Inverter Power Connector

The connector supports 1A current (maximum).

Pin # Signal Name

1 +12V

2 NC

3 Ground

J4: VGA Chipset Fan Power Connector

Pin # Signal Name

1 +12V

2 Ground

J5, J6: LVDS Connectors (2nd channel, 1st channel)

The LVDS connectors, DF13 20-pin mating connectors, are composed of

the first channel (J6) and second channel (J5) to support 24-bit or 48-bit.

Signal Name Pin # Pin # Signal Name

TX0- 2 1 TX0+

Ground 4 3 Ground

TX1- 6 5 TX1+

5V/3.3V 8 7 Ground

TX3- 10 9 TX3+

TX2- 12 11 TX2+

Ground 14 13 Ground

TXC- 16 15 TXC+

5V/3.3V 18 17 ENABKL

+12V 20 19 +12V

Remarks: Maximum current for +12V is 1A.

JP1: LVDS Panel Power Select

JP1 Setting Panel Voltage

Pin 1-2

Short/Closed

3.3V (default)

Pin 2-3

Short/Closed

5V

INSTALLATIONS

16 IB850 User’s Manual

Page is loading ...

Intel IB850 User manual

Intel IB850 User manual

Related papers

Other documents