Sony DSC-U60 User manual

3-078-724-11(1)

Digital Still Camera

Operating Instructions

Before operating the unit, please read this manual and the separate sheet

“Waterproof specifications” thoroughly, and retain it for future reference.

Owner’s Record

The model and serial numbers are located on the bottom. Record the

serial number in the space provided below. Refer to these numbers

whenever you call upon your Sony dealer regarding this product.

Model No. DSC-U60

Serial No.

2

On the battery charger

To prevent fire or shock hazard, do

not expose the unit to rain or

moisture.

If you have any questions about this product,

you may call:

Sony Customer Information Services Center

1-800-222-SONY (7669)

The number below is for the FCC related

matters only.

Regulatory Information

CAUTION

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

Note:

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed

and used in accordance with the instructions,

may cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or

television reception, which can be determined

by turning the equipment off and on, the user

is encouraged to try to correct the interference

by one or more of the following measures:

– Reorient or relocate the receiving

antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

The supplied interface cable must be used

with the equipment in order to comply with

the limits for a digital device pursuant to

Subpart B of Part 15 of FCC Rules.

WARNING

For the Customers in the U.S.A.

This symbol is intended to

alert the user to the presence

of uninsulated “dangerous

voltage” within the product’s

enclosure that may be of

sufficient magnitude to

constitute a risk of electric

shock to persons.

This symbol is intended to

alert the user to the presence

of important operating and

maintenance (servicing)

instructions in the literature

accompanying the appliance.

Declaration of Conformity

Trade Name: SONY

Model No.: DSC-U60

Responsible Party:Sony Electronics Inc.

Address: 680 Kinderkamack

Road, Oradell, NJ 07649

U.S.A.

Telephone No.: 201-930-6972

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This device

may not cause harmful interference, and

(2) this device must accept any interference

received, including interference that may

cause undesired operation.

3

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO WIDE SLOT,

FULLY INSERT.

A moulded plug complying with BS1363 is fitted

to this equipment for your safety and

convenience.

Should the fuse in the plug supplied need to be

replaced, a fuse of the same rating as the supplied

one and approved by ASTA or BSI to BS1362,

(i.e., marked with or mark) must be used.

If the plug supplied with this equipment has a

detachable fuse cover, be sure to attach the fuse

cover after you change the fuse. Never use the

plug without the fuse cover. If you should lose the

fuse cover, please contact your nearest Sony

service station.

This product has been tested and found

compliant with the limits sets out in the EMC

Directive for using connection cables shorter

than 3 meters (9.8 feet).

Attention

The electromagnetic fields at the specific

frequencies may influence the picture of this

camera.

Notice

If static electricity or electromagnetism causes

data transfer to discontinue midway (fail),

restart the application or disconnect and

connect the USB cable again.

Certain countries may regulate disposal of the

battery used to power this product. Please

consult with your local authority.

For the Customers in the U.S.A.

and Canada

THIS DEVICE COMPLIES WITH PART 15

OF THE FCC RULES. OPERATION IS

SUBJECT TO THE FOLLOWING TWO

CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE

HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY

INTERFERENCE RECEIVED,

INCLUDING INTERFERENCE THAT MAY

CAUSE UNDESIRED OPERATION.

THIS CLASS B DIGITAL APPARATUS

COMPLIES WITH CANADIAN ICES-003.

For the Customers in the U.S.A.

and Canada

RECYCLING NICKEL METAL

HYDRIDE BATTERIES

Nickel Metal Hydride

batteries are recyclable.

You can help preserve our

environment by returning your

used rechargeable batteries to

the collection and recycling location

nearest you.

For more information regarding recycling

of rechargeable batteries, call toll free

1-800-822-8837, or visit

http://www.rbrc.org/

CAUTION:

Do not handle damaged or leaking Nickel

Metal Hydride batteries.

4

Before using your camera

Notes on waterproof performance

• This camera conforms to IEC60529 IPX6* and

IPX7**, and can be used in places exposed to

splashing water or underwater up to depths of

1.5 m (5 feet).

* Water shall not enter the interior even when

exposed to direct jet streams of water (normal

temperature fresh water) from any direction.

** Water shall not seep into the interior even

when left submerged in normal temperature

fresh water at a depth of 1 m (3 feet

3 1/4 inches) in a stationary condition for

approximately 30 minutes.

• You can use this camera in the following

places: underwater (ocean, swimming pools) up

to depths of 1.5 m (5 feet), beachside, riverside,

poolside, ski slopes, in the rain, etc.

• Do not use this camera in the following places:

places where the camera might be subject to

high water pressure, hot springs or bathtubs,

etc.

Notes on use

• Before using this camera underwater or in

places exposed to water, be sure to inspect the

O-ring and the O-ring mating surface on the

inside of the camera.

• Do not immerse the camera in water containing

soap, detergent, bath salts, etc., or in hot water

with a temperature of more than 30°C.

• Never open the waterproof cover underwater or

in places exposed to water. Lock the lock

switch to prevent the waterproof cover from

opening by accident.

• This camera does not float in water.

• Before opening the waterproof cover, be sure to

rinse off any sand and completely wipe away

any water that may be present on the camera

body.

• Should you find any evidence of water leaks

inside the waterproof cover, stop using the

camera at once and contact your Sony dealer or

local authorized Sony service facility.

• Sony cannot be held responsible for

malfunctions or irreparable problems arising

from water or foreign objects entering the

inside of the camera due to improper handling.

• Note that waterproof performance is not

guaranteed under all environments and

conditions.

Trial recording

Before you record one-time events, you may want

to make a trial recording to make sure that the

camera is working correctly.

No compensation for contents of the

recording

Contents of the recording cannot be compensated

for if recording or playback is not possible due to

a malfunction of your camera or recording media,

etc.

Back up recommendation

To avoid the potential risk of data loss, always

copy (back up) data to a disk.

Notes on image data compatibility

• This camera conforms with the Design rule for

Camera File system universal standard

established by the JEITA (Japan Electronics

and Information Technology Industries

Association).

• Playback of images recorded with your camera

on other equipment and playback of images

recorded or edited with other equipment on

your camera are not guaranteed.

Note on “Memory Stick”

This camera turns off when you open the inner

cover. Do not open the inner cover while the

access lamp is lit.

Precaution on copyright

Television programs, films, video tapes, and other

materials may be copyrighted. Unauthorized

recording of such materials may be contrary to

the provision of the copyright laws.

Do not shake or strike the camera

In addition to malfunctions and inability to record

images, this may render the “Memory Stick”

unusable or image data breakdown, damage or

loss may occur.

5

LCD screen, LCD finder (only models

6

Table of contents

Before using your camera.........................4

How to hold the camera............................5

Identifying the parts..................................8

Preparing batteries ..................................10

Charging the batteries.............................10

Inserting the batteries..............................12

Using your camera abroad......................15

Turning on/off your camera....................15

How to use the buttons............................16

Setting the date and time.........................16

Inserting and removing a “Memory

Stick”..............................................18

Setting the still image size ......................20

Image size...............................................21

Basic still image shooting

— Using auto adjustment mode.....22

Using the self-timer............................24

Selecting a flash mode........................25

Creating or selecting a folder..................26

Creating a new folder .........................27

Selecting the recording folder.............28

Shooting according to scene conditions

— Scene Selection..........................30

Setting the distance to the subject

— Focus preset...............................32

Shooting five images continuously

— Burst.......................................... 33

Adding special effects

— Picture Effect ............................ 34

Viewing still images on the LCD

screen ............................................. 36

Viewing single images....................... 36

Viewing an index screen

(four-image)................................... 37

Selecting the folder and playing back

images — Folder............................ 38

Enlarging an image

— Enlarged playback..................... 40

Choosing images to print

— Print (DPOF) mark.................... 41

Shooting movies..................................... 43

Viewing movies on the LCD screen....... 44

Deleting images...................................... 46

Formatting a “Memory Stick”................ 47

Copying images to your computer

— For Windows users....................49

Installing the USB driver....................50

Installing “Image Transfer”................51

Installing “ImageMixer”.....................52

Connecting the camera to your

computer.........................................53

Copying images using “Image

Transfer”.........................................54

Changing “Image Transfer” settings...55

Copying images without using “Image

Transfer”.........................................55

Viewing images on your computer.....56

Image file storage destinations and file

names..............................................57

Copying images to your computer

— For Macintosh users ..................58

Creating a Video CD using

“ImageMixer”.................................60

Getting started

Shooting still images

Viewing still images

Enjoying movies

Deleting images

Enjoying images on your

computer

7

Troubleshooting ......................................61

Warnings and messages ..........................68

Self-diagnosis display

— If a code starting with an alphabet

letter appears...................................70

Menu items..............................................71

Precautions..............................................74

On “Memory Stick” ................................76

On Nickel-Metal Hydride batteries.........78

On the battery charger.............................79

On the O-ring ..........................................79

Specifications..........................................82

LCD screen displays ...............................83

Index........................................................85

Troubleshooting

Additional information

Index

8

Identifying the parts

See the pages in parentheses for details of operation.

9

qs

8

7

6

2

1

4

3

9

qa

0

5

A LCD screen

B POWER lamp (15)

C POWER button (15)

D MENU button (16)

E Mode switch

: To view images (36)

: To shoot still images (22)

To shoot five images

continuously (33)

: To shoot movies (43)

F Shutter button (22)

G (Flash charge) lamp (orange)

(26)

H Control buttons

Menu on: v/V (16)

Menu off: /SCENE (25, 30)

I Lock switch (12)

J OPEN button (12)

K Slide lock lever (12)

L EXEC button (16)

When viewing images:

(Enlarged playback) (40)

10

Preparing batteries

Use the following batteries in this camera.

Acceptable batteries

HR11/45: HR03 (size AAA) Nickel-Metal

Hydride batteries (2)

– NH-AAA-DA (2) (supplied)

– NH-AAA-2DA twin-pack (not supplied)

Batteries that cannot be used

Manganese batteries, lithium batteries, Ni-

Cd batteries, alkaline batteries

• When the above batteries are used, operation is

not guaranteed due to possible voltage drops or

other characteristics of the batteries.

In addition, the battery remaining indicator is

not displayed correctly.

Charging the batteries

, Insert Nickel-Metal Hydride

batteries into the battery

charger (supplied) with the

correct polarity +/–.

• You cannot use any battery other than a Nickel-

Metal Hydride battery. Also, operations are not

guaranteed when using a Nickel-Metal Hydride

battery from a manufacturer other than Sony.

• Be sure to charge the Nickel-Metal Hydride

batteries supplied with your camera before

using them for the first time.

• Connect the battery charger to an easily

accessible wall outlet (wall socket) close by.

• Even if the CHARGE lamp is not lit, the battery

charger is not disconnected from the AC power

source (mains) as long as it is connected to the

wall outlet (wall socket). If some trouble occurs

while using the battery charger, immediately

shut off the power by disconnecting the plug

from the wall outlet (wall socket).

, Connect the battery charger to

a wall outlet (wall socket) using

the power cord (mains lead).

The CHARGE lamp lights up when

charging begins, and goes off when

charging is completed.

For details on the supplied battery charger,

see page 79.

• When charging is finished, disconnect the

power cord (mains lead) from the wall outlet

(wall socket), and remove the Nickel-Metal

Hydride batteries from the battery charger.

1

2

To the wall outlet

(wall socket)

Power cord

(mains lead)

CHARGE lamp

G

e

tti

ng s

t

ar

t

e

d

11

Getting started

Charging time

This represents the time required to charge

fully depleted Nickel-Metal Hydride

batteries using the supplied battery charger

in an environment where the ambient

temperature is 25°C (77°F).

• It takes about six hours to completely charge

the batteries. The CHARGE lamp may remain

lit longer than six hours, but this is not a

malfunction.

• If you use the BC-CSQ2 battery charger

supplied with the STAMINA “Super Quick

charge” kit (not supplied), the batteries will

charge faster.

Charging time for Size AAA Nickel-Metal

Hydride batteries

2 batteries: Approx. 1 hour 25 minutes

4 batteries: Approx. 2 hours 50 minutes

Notes on the Nickel-Metal

Hydride batteries

• If the poles of the Nickel-Metal Hydride

batteries are dirty, the batteries may not charge

properly. Occasionally clean the poles of the

batteries and the terminals of the charger by

wiping them with a dry cloth.

• Always use the supplied case when transporting

the Nickel-Metal Hydride batteries. If the

positive and negative terminals come into

contact with metallic material and are shorted,

the batteries could overheat or catch fire.

• At the time of purchase, or when the Nickel-

Metal Hydride batteries have not been used for

a long time, they may not fully charge. This is

typical of this type of battery, and is not a

malfunction. If this happens, repeatedly using

up the batteries fully, and then charging them,

should correct the problem.

• Even when Nickel-Metal Hydride batteries are

not being used they lose their charge naturally

over time. It is recommended that you recharge

the batteries just before using them.

• If you recharge Nickel-Metal Hydride batteries

before fully using up the existing charge, the

low battery warning may be displayed sooner

than expected. This is called the “memory

effect.”* If this problem occurs, charging the

batteries only after using up the existing charge

will correct it.

* The “memory effect” – the situation in which

the capacity of the battery is temporarily

lowered.

• Do not peel off the external seals or damage the

batteries. Never use batteries from which the

seals have been partially or completely

removed, or batteries that have been split in any

way. These may cause leakage, explosion, or

heat-up of the battery, and personal scald or

injury may be caused. These may cause a

malfunction of the battery charger.

Nickel-Metal Hydride

battery

Charging time

NH-AAA-DA × 2 (supplied) Approx. 6 hours

12

Inserting the batteries

, Slide the lock switch and the

OPEN button in the direction of

the arrow and open the

waterproof cover.

The waterproof cover opens toward you.

• Before opening the waterproof cover, be

sure to rinse off any sand and

completely wipe away any water that

may be present on the camera body.

• Never open the waterproof cover underwater or

in places exposed to water, as this may allow

water to enter the inside of the camera and

cause a malfunction.

• Immediately after the camera is brought from a

warm place to a cold place such as from

indoors to outdoors, the difference in pressure

between the inside of the camera and the

outside air may make it difficult to open the

waterproof cover.

, Slide the inner cover in the

direction of the arrow to open

it.

The inner cover opens toward you when

you slide it in the direction of the arrow.

, Insert the batteries.

Match the +/– poles of the batteries to the

+/– marks inside the battery case.

• From time to time, use a dry cloth to wipe any

dirt off of the battery terminals and the contacts

inside the inner cover. Skin oil and other dirt on

the battery terminals and contacts can

significantly shorten the operating time

provided by the batteries.

1

2

3

13

Getting started

, Close the inner cover and slide

it in the direction of the arrow

to lock it.

Close the inner cover while holding the

batteries in. Make sure the cover is closed

securely.

To remove the batteries

Perform steps 1 and 2 and remove the

batteries.

• Be careful not to drop the batteries when

opening or closing the inner cover.

, Inspect the waterproof cover.

Inspect the O-ring and the O-ring mating

surface for scratches, deformation, dirt, hair

or other problems.

• Note that if the O-ring and the O-ring mating

surface are damaged, dirty or have other

problems, the waterproof performance may be

impaired. In this case, water may enter the

inside of the camera and cause irreparable

damage.

• Replace the O-ring with a new one if it

becomes scratched or deformed, or after

approximately two years of use even if there are

no problems (page 81).

, Close the waterproof cover.

Close the waterproof cover and slide the

slide lock lever back into place until the

OPEN button clicks.

• When using the camera underwater or in places

exposed to water, slide the lock switch (page 9)

to lock the waterproof cover. This prevents the

waterproof cover from opening by accident.

4

14

Battery remaining indicator

(When using Nickel-Metal

Hydride batteries)

As the battery power decreases with use, the

battery remaining indicator displays the

amount of power remaining using the

following symbols.

• If the LCD screen display is off, set

[DISPLAY] in [ ] to [ON].

• Based on the conditions under which the

camera is being used and the state of the

charge, or on the environment, this information

may not be correctly indicated.

• The battery remaining indicator is not

displayed in USB connecting.

Battery life and number of

images that can be recorded/

viewed

The tables show the approximate battery

life and the number of images that can be

recorded/viewed with fully charged

batteries at a temperature of 25°C (77°F) in

auto adjustment mode. The numbers of

images that can be recorded/viewed take

into account changing the supplied

“Memory Stick” as necessary. Note that the

actual numbers may be less than indicated

depending on the conditions of use.

Shooting still images

Under the average conditions

1)

1) Shooting in the following situations:

– Shooting one time every 30 seconds

– The flash strobes once every two times

– The power turns on and off once every ten

times.

Viewing still images

2)

2) Viewing single images in order at about 3-

second intervals with [LCD LIGHT] set to

[ON]

Shooting movies

3)

3) The maximum shooting time is 15 seconds.

• The remaining indicator will decrease in the

following situations:

– The surrounding temperature is low

– The flash is used

– The camera has been turned on and off many

times

– [LCD LIGHT] is set to [ON]

– The battery capacity decreases as you use it

more and more and as time passes (page 78).

Battery

remaining

indicator

Battery remaining

guidelines

Sufficient power remaining

Battery half full

Battery low, recording/

playback will stop soon.

Change the batteries for fully

charged ones, or charge these

batteries.

(The warning indicator flashes.)

Image

size

NH-AAA-DA (2) (supplied)

LCD

LIGHT

No. of

images

Battery

life (min.)

2.0M

ON Approx. 140 Approx. 70

OFF Approx. 160 Approx. 80

VGA

ON Approx. 140 Approx. 70

OFF Approx. 160 Approx. 80

Image

size

NH-AAA-DA (2) (supplied)

No. of

images

Battery life

(min.)

2.0M Approx. 3000 Approx. 150

VGA Approx. 3000 Approx. 150

NH-AAA-DA (2) (supplied)

Continuous

recording

LCD LIGHT

Battery life

(min.)

ON Approx. 80

OFF Approx. 90

15

Getting started

Using your camera

abroad

Power sources

You can use your camera in any country or

region with the supplied battery charger

within 100 V to 240 V AC, 50/60 Hz. Use a

commercially available AC plug adaptor

[a], if necessary, depending on the design of

the wall outlet (wall socket) [b].

• Do not use an electronic transformer (travel

converter), as this may cause a malfunction.

BC-CS2A/CS2B

Turning on/off your camera

, Press POWER to turn on the

power.

The POWER lamp (green) lights up and the

power is on. When you turn on your camera

for the first time, the DATE NOTATION

screen appears on the LCD screen

(page 16).

To turn off the power

Press POWER again. The POWER lamp

goes out, and the camera turns off.

Auto power-off function

If you do not operate the camera for about

three minutes, the camera turns off

automatically to prevent wearing down the

batteries.

However, the auto power-off function will

not operate when the camera is connected to

a computer with the USB cable.

P

O

W

E

R

POWER

POWER lamp

16

How to use the

buttons

To change the current settings of the

camera, bring up the menu, and use the

control buttons to make the changes.

For each item, press MENU to display the

menu and press the control buttons v/V to

select the desired value, then press EXEC to

make the setting.

Press MENU, then the menu disappears

from the LCD screen.

EXEC

MENU

Control

buttons

Setting the date and time

, Press POWER to turn on the

power.

The POWER lamp (green) lights up and the

DATE NOTATION screen appears on the

LCD screen.

• To change the date and time, press MENU and

select [DATE&TIME SET] in [CLOCK SET]

under [ ] (page 73), then perform step 3.

When the setting is complete, press MENU so

that the CLOCK SET screen disappears from

the LCD screen.

• This operation is available no matter what

position the mode switch is in.

, Select the desired date display

format with the control buttons

v/V, then press EXEC.

Select from [Y/M/D] (year/month/day),

[M/D/Y] (month/day/year) or [D/M/Y]

(day/month/year). Then DATE&TIME

SET screen appears on the LCD screen.

• If the rechargeable button battery, which

provides the power for saving the time data, is

ever fully discharged (page 76), the DATE

NOTATION screen will appear again. When

this happens, reset the date and time, by starting

from step 2.

1

P

O

W

E

R

M/D/Y

D/M/Y

2003

12:00:00

AM

DATE NOTATION

11

Y/M/D

POWER

2

Y/M/D

12:00

AM

DATE&TIME SET

1 12003

EXEC

17

Getting started

, Set the numeric value with the

control buttons v/V, then

press EXEC.

The item to be set is indicated with v/V.

After entering the number, v/V moves to

the next item. Repeat this step until all of

the items are set.

• If you selected [D/M/Y] in step 2, set the time

on a 24-hour cycle.

, Select [OK] with the control

button v, then press EXEC.

The date and time are entered and the clock

starts to keep time.

• If you make a mistake, select [CANCEL] in

step 4 to display the DATE NOTATION

screen, then repeat the procedure from step 2.

• To cancel the date and time setting, select

[CANCEL], then press EXEC.

3

Y/M/D

12:00

AM

DATE&TIME SET

2003 1 1

EXEC

4

Y/M/D

10:30

AM

DATE&TIME SET

2003 7 4

CANCEL

OK

EXEC

18

Inserting and removing a “Memory Stick”

, Slide the lock switch and the

OPEN button in the direction of

the arrow and open the

waterproof cover.

The waterproof cover opens toward you.

• Before opening the waterproof cover, be

sure to rinse off any sand and

completely wipe away any water that

may be present on the camera body.

• Never open the waterproof cover underwater or

in places exposed to water, as this may allow

water to enter the inside of the camera and

cause a malfunction.

• Immediately after the camera is brought from a

warm place to a cold place such as from

indoors to outdoors, the difference in pressure

between the inside of the camera and the

outside air may make it difficult to open the

waterproof cover.

, Slide the inner cover in the

direction of the arrow to open

it.

The inner cover opens toward you when

you slide it in the direction of the arrow.

• For details on the “Memory Stick,” see page 76.

, Insert the “Memory Stick.”

Holding the “Memory Stick” as shown in

the illustration, insert it all the way in until

it clicks.

• Push the “Memory Stick” all of the way in so

that it is securely seated in the connector. If the

“Memory Stick” is not inserted correctly, you

may not be able to record or display images in

the “Memory Stick.”

• Be careful not to drop the batteries when

opening or closing the inner cover.

1

19

Shooting still images

, Close the inner cover and slide

it in the direction of the arrow

to lock it.

Make sure the cover is closed securely.

To remove a “Memory Stick”

Perform steps 1 and 2, and push the

“Memory Stick” to pop it out. When doing

so, be careful not to drop the “Memory

Stick.”

• When the access lamp is lit up, it means

that image data is being read or written.

Never open the inner cover or turn off

the power at this time, as the data may

be damaged.

, Inspect the waterproof cover.

Inspect the O-ring and the O-ring mating

surface for scratches, deformation, dirt, hair

or other problems.

• Note that if the O-ring and the O-ring mating

surface are damaged, dirty or have other

problems, the waterproof performance may be

impaired. In this case, water may enter the

inside of the camera and cause irreparable

damage.

• Replace the O-ring with a new one if it

becomes scratched or deformed, or after

approximately two years of use even if there are

no problems (page 81).

, Close the waterproof cover.

Close the waterproof cover and slide the

slide lock lever back into place until the

OPEN button clicks.

• When using the camera underwater or in places

exposed to water, slide the lock switch (page 9)

to lock the waterproof cover. This prevents the

waterproof cover from opening by accident.

4

20

Setting the still image size

, Set the mode switch to , and

turn on the power, then press

MENU.

The menu appears on the LCD screen.

, Select [ ] with the control

button v, then press EXEC.

Select [SIZE·BURST] with the

control buttons v/V, then

press EXEC.

The image size is displayed.

• For details on the image size, see page 21.

, Select the desired image size

with the control buttons v/V,

then press EXEC.

The image size is set.

When the setting is complete, press MENU

so that the menu disappears from the LCD

screen.

• The image size selected here is maintained even

when the power is turned off.

1

RETURN

FOCUS

SELFTIMER

P.EFFECT

AUTO

OFF

SIZE

BURST

•

2.0M

MENU

2

RETURN

FOCUS

SELFTIMER

P.EFFECT

AUTO

OFF

SIZE

BURST

•

2.0M

EXEC

3

SIZE • BURST

BURST

VGA

2.0M

VGA

2.0M

EXEC

Page is loading ...

Sony DSC-U60 User manual

Sony DSC-U60 User manual

Related papers

Other documents