EMS FireCell Radio Hub Quick start guide

Brand: EMS

Model: FireCell Radio Hub

Category: Fire protection

Type: Quick start guide

RADIO HUB

QUICK START GUIDE

POWER

FAU LT

SYSTEM

FAU LT

POWER

FAU LT

FIRE

Fire Alarm Control

Radio Hub

Control Panel

Radio Cluster

Communicator (RCC)

230V AC

Radio Hub Quick Start Guide Iss 7 - MK139 AJM

www.emsgroup.co.uk

Step 1 Identify the Hub Location:

The Radio Hub is powered from the Control Panels loop connection. If a radio survey

has been carried out the survey will detail the recommended location of the Radio

Hub along with the Control Panel that it will be connected nearby. The Radio Hub is

required to be connected via glands to the specied Control Panel (CIE). The

recommended minimum distance between metal objects from the aerial is 600mm.

The recommended minimum distance to any other electrical equipment is 2 metres.

FIRE

Fire Alarm Control

FIRE

Fire Alarm Control

POWER

FAU LT

POWER

FAU LT

WITHIN 10m

FIRE

Fire Alarm Control

POWER

FAU LT

POWER

FAU LT

POWER

FAU LT

2m AWAY

FROM OTHER

ELECTRICAL

EQUIPMENT

600mm AWAY FROM METAL *

300mm is an acceptable distance where 600mm

is not achievable

NEVER SITE HUB BELOW OR TO THE SIDE OF THE PANEL

NEVER SITE HUB NEAR METAL WORK OR ELECTRICAL EQUIPMENT

HUB CORRECTLY SITED ABOVE

PANEL

FIRE

Fire Alarm Control

POWER

FAU LT

Open the unit and carefully remove the inner PCB. The loop cable entries can now be

made. See entry points below:

Step 2 Prepare the Hub Box:

Step 3 Fix the Hub to the Wall:

The unit can now be xed to the wall. The PCB and connecting lead can now be

carefully re-inserted. The Hubs xing positions are as below:

FIXING POSITION 1

FIXING POSITION 4 FIXING POSITION 5

FIXING POSITION 3FIXING POSITION 2

NO CABLE ACCESS

AT TOP OF UNIT!

Re-Sound

Alarm

Power On

Fire

Pre-Alarm

On Test

Buzzer Silenced

Delay Active

NO CABLE ACCESS

The Radio Hub has up to four seperate sets of loop connections: LOOP IN -, LOOP IN +,

LOOP OUT - and LOOP OUT + for each available loop. The cable must be passed

through the entry points provided. Connections are detailed below:

Step 4 Radio Hub Wiring:

REMOTE PSU 24V

OUT

AUX

24V

LOOP

OUT

NET

OUT

COMMSS1

+ -+ - + - PF NO C NC NO C NC NO C NCFLT RES INT CNT SIL 0V+ - + - + - + - + -

LOOP

OUT

LOOP

LOOP 2

(If tted)

+ - + -

+ - + - + -

S2 INPUTS FAULT FIRE ALARM

Exit

Fires

Enable ControlFunctionEvacuateReset

Lamp

Test

Silence

Buzzer

Silence Alarm

(Acknowledge)

Re-Sound

Alarm

Power On

Fire

More Events

General

Disablement

General Fault

Power Fault

System Fault

Sounder

Pre-Alarm

On Test

Buzzer Silenced

Delay Active

Events

Enter

Fire in Zone

1 2 4 5 6 7 8 9 10 11 12 13 14 15 163

REMOTE PSU 24V

OUT

AUX

24V

LOOP

OUT

NET

OUT

COMMSS1

+ -+ - + - PF NO C NC NO C NC NO C NCFLT RES INT CNT SIL 0V+ - + - + - + - + -

LOOP

OUT

LOOP

LOOP 2

(If tted)

+ - + -

+ - + - + -

S2 INPUTS FAU LT FIRE ALARM

Exit

Fires

Enable ControlFunctionEvacuateReset

Lamp

Test

Silence

Buzzer

Silence Alarm

(Acknowledge)

Re-Sound

Alarm

Fire

More Events

General

Disablement

General Fault

Power Fault

System Fault

Sounder

Buzzer Silenced

Delay Active

Fire in Zone

1 2 4 5 6 7 8 9 10 11 12 13 14 15 163

+ - + -

LOOP 1

OUT

LOOP 1

PANEL

NOTE: Repeat for

loops 2-4 if used

OUT +

OUT -

IN +

IN -

IN +

IN -

OUT +

OUT -

HUB

+ - + -

LOOP 1

OUT

The information contained within this literature is correct at time of publishing. EMS reserves the right to change any information regarding products as part of its continual development

enhancing new technology and reliability. EMS advises that any product literature issue numbers are checked with its head oce prior to any formal specication being written.

enquiries@emsgroup.co.uk

www.emsgroup.co.uk

+44 (0) 1227 369570