2. allgood
  3. FT9451
FT9451

allgood FT9451 Operating instructions

  • Hello! I've reviewed the fixing template for the 9451 and 9461 door closers. This document provides detailed instructions including the bracket installation, drilling angles and maintenance guidance. I'm ready to answer your questions about the installation and maintenance of these closers.
  • What angle are the closer body fixing holes to be drilled at?
    What size screws should be used for fixing?
    What is the annual maintenance for the closers?
    What type of bracket is required?
T: 020 7387 9951 www.allgood.co.uk
UNDERSIDE OF HEAD FRAME
HOW TO USE TEMPLATE:
HOLE IN DOOR FOR CONCEALED WIRING FROM CONCEALED
CABLE LOOP OR CONDUCTOR HINGE.
10mm DIA BORED ON CENTRE LINE OF DOOR AND PLUGGED
AT THE HEAD.
THIS CLOSER WILL ALLOW THE DOOR TO BE OPENED TO 180°
HINGE CENTRELINE
Fixing Template For:
9451 / 9461 Closers.
(To Be Read With Fixing Instruction FI9451).
FT9451
Issue 04-03/22
18° 18°
T: 020 7387 9951 1www.allgood.co.uk
Recycle Responsibly
123875830 58
35
13
CLOSER BODY FIXING HOLES MUST BE DRILLED
AT AN ANGLE OF 18° (SEE DIAGRAM BELOW).
4 x 32mm No. 8 SELF TAPPING SCREWS.
DRILL SIZE 3mm.
24
27
MAINTENANCE:
THE INTERNAL MECHANISM OF THE CLOSERS ARE IMMERSED IN OIL AND ARE
LUBRICATED DURING OPERATION. ANNUAL MAINTENANCE SHOULD INCLUDE
THE SECURITY OF ALL FIXINGS AND THE LUBRICATION OF THE ARM PIVOT POINTS.
273
ALTERNATIVE FRAME BRACKET 9151FN MUST BE MORTICED INTO THE HEAD FRAME.
ALIGNMENT MARKS ON THE BRACKET MUST BE IN LINE WITH THE FACE OF THE DOOR.
BRACKET SETTING MARKS MUST
ALIGN WITH DOOR FACE
QUALITY SINCE 1948
Fixing template for:
9451 / 9461 Closers
To be read with Fixing Instruction Fl9451).
FT9451A Issue 04-03/22
T: 020 7387 9951 www.allgood.co.uk
UNDERSIDE OF HEAD FRAME
HINGE CENTRELINE
2
30
35
58
Fixing Template For:
9451 / 9461 Closers.
(To Be Read With Fixing Instruction FI9451).
FT9451
Issue 04-03/22
13
87123
24
27
273
18°18°
CLOSER BODY FIXING HOLES MUST BE DRILLED
AT AN ANGLE OF 18° (SEE DIAGRAM BELOW).
4 x 32mm No. 8 SELF TAPPING SCREWS.
DRILL SIZE 3mm.
MAINTENANCE:
THE INTERNAL MECHANISM OF THE CLOSERS ARE IMMERSED IN OIL AND ARE
LUBRICATED DURING OPERATION. ANNUAL MAINTENANCE SHOULD INCLUDE
THE SECURITY OF ALL FIXINGS AND THE LUBRICATION OF THE ARM PIVOT POINTS.
HOW TO USE TEMPLATE:
HOLE IN DOOR FOR CONCEALED WIRING FROM CONCEALED
CABLE LOOP OR CONDUCTOR HINGE.
10mm DIA BORED ON CENTRE LINE OF DOOR AND PLUGGED
AT THE HEAD.
THIS CLOSER WILL ALLOW THE DOOR TO BE OPENED TO 180°
ALTERNATIVE FRAME BRACKET 9151FN MUST BE MORTICED INTO THE HEAD FRAME.
ALIGNMENT MARKS ON THE BRACKET MUST BE IN LINE WITH THE FACE OF THE DOOR.
T: 020 7387 9951 www.allgood.co.uk
Recycle Responsibly
BRACKET SETTING MARKS MUST
ALIGN WITH DOOR FACE
QUALITY SINCE 1948
Fixing template for:
9451 / 9461 Closers
To be read with Fixing Instruction Fl9451).
FT9451A Issue 04-03/22
/