ALLEGION SCHLAGE 7000 SERIES Installation guide
- Type
- Installation guide
NOTE:
All applications involving door closers require 2x through-fixing screws
and 2x self-tapping wood screws to be fitted to each rose.
Failure to do so may void manufacturers’ warranty.
DOOR PREPARATION
A
When drilling through the door, drill from both sides to avoid
damaging the door.
B
Accurate door preparation is essential for the functioning of this lock.
Please follow the enclosed template and instructions carefully.
Through-bolt fixing is recommended.
Drill a 35mm hole through the door for privacy sets and a
C
25mm hole for passage sets.
Drill 2x 5mm holes through the door where through-bolt xing
is required.
Drill a 24mm hole x 85mm deep into the front edge of the
door.
Mark centre for either passage or privacy set.
Mark holes for through-bolt xing where required.
A
B
C
Fold template at correct height
(suggested height for centreline is 970mm from oor)
4
4
4
4
4
DRILL HOLES
Mark centre of door thickness on horizontal centreline.
3
3
3
3
3
1
1
1
1
1
2
2
2
2
2
P R E P AR E J AMB & INS TALL S TR IKEINS TALL LAT C H
A
B
C
A
B
C
Insert latch into hole. Trace around face plate.
Chisel out wood until facepate ts ush with door edge.
Fasten latch to door so bevelled edge of latchbolt faces
jamb.
5
5
5
5
5
6
6
REMOVE ROSE CAPS
A
B
INSTALL FURNITURE
Mark vertical line and height centreline on jamb, exactly
opposite centre of latch.
Drill 2x 20mm holes x 15mm deep, 8mm above and below
height centreline.
Use strike plate as pattern for cutout. Chisel out and install strike.
(Privacy Set illustrated)
(Universal Strike illustrated)
Insert spindles into furniture, as illustrated.
Attach furniture to door by through-bolt xing. Cut bolts to appropriate length,
ush against the rose.
Fit self-tapping wood screws to each rose as necessary.
NOTE:
All applications involving door closers require 2x through-fixing screws
and 2x self-tapping wood screws to be fitted to each rose.
Failure to do so may void manufacturers’ warranty.
DOOR PREPARATION
A
When drilling through the door, drill from both sides to avoid
damaging the door.
B
Accurate door preparation is essential for the functioning of this lock.
Please follow the enclosed template and instructions carefully.
Through-bolt fixing is recommended.
Drill a 35mm hole through the door for privacy sets and a
C
25mm hole for passage sets.
Drill 2x 5mm holes through the door where through-bolt xing
is required.
Drill a 24mm hole x 85mm deep into the front edge of the
door.
Mark centre for either passage or privacy set.
Mark holes for through-bolt xing where required.
A
B
C
Fold template at correct height
(suggested height for centreline is 970mm from oor)
4
4
4
4
4
DRILL HOLES
Mark centre of door thickness on horizontal centreline.
3
3
3
3
3
1
1
1
1
1
2
2
2
2
2
P R E P AR E J AMB & INS T ALL S TR IKEINS T ALL L ATC H
A
B
C
A
B
C
Insert latch into hole. Trace around face plate.
Chisel out wood until facepate ts ush with door edge.
Fasten latch to door so bevelled edge of latchbolt faces
jamb.
5
5
5
5
5
6
6
REMOVE ROSE CAPS
A
B
INSTALL FURNITURE
Mark vertical line and height centreline on jamb, exactly
opposite centre of latch.
Drill 2x 20mm holes x 15mm deep, 8mm above and below
height centreline.
Use strike plate as pattern for cutout. Chisel out and install strike.
(Privacy Set illustrated)
(Universal Strike illustrated)
Insert spindles into furniture, as illustrated.
Attach furniture to door by through-bolt xing. Cut bolts to appropriate length,
ush against the rose.
Fit self-tapping wood screws to each rose as necessary.
1
NOTE:
All applications involving door closers require 2x through-fixing screws
and 2x self-tapping wood screws to be fitted to each rose.
Failure to do so may void manufacturers’ warranty.
DOOR PREPARATION
A
When drilling through the door, drill from both sides to avoid
damaging the door.
B
Accurate door preparation is essential for the functioning of this lock.
Please follow the enclosed template and instructions carefully.
Through-bolt fixing is recommended.
Drill a 35mm hole through the door for privacy sets and a
C
25mm hole for passage sets.
Drill 2x 5mm holes through the door where through-bolt xing
is required.
Drill a 24mm hole x 85mm deep into the front edge of the
door.
Mark centre for either passage or privacy set.
Mark holes for through-bolt xing where required.
A
B
C
Fold template at correct height
(suggested height for centreline is 970mm from oor)
4
4
4
4
4
DRILL HOLES
Mark centre of door thickness on horizontal centreline.
3
3
3
3
3
1
1
1
1
1
2
2
2
2
2
P R E P AR E J AMB & INS TALL S TR IKEINS TALL LAT C H
A
B
C
A
B
C
Insert latch into hole. Trace around face plate.
Chisel out wood until facepate ts ush with door edge.
Fasten latch to door so bevelled edge of latchbolt faces
jamb.
5
5
5
5
5
6
6
REMOVE ROSE CAPS
A
B
INSTALL FURNITURE
Mark vertical line and height centreline on jamb, exactly
opposite centre of latch.
Drill 2x 20mm holes x 15mm deep, 8mm above and below
height centreline.
Use strike plate as pattern for cutout. Chisel out and install strike.
(Privacy Set illustrated)
(Universal Strike illustrated)
Insert spindles into furniture, as illustrated.
Attach furniture to door by through-bolt xing. Cut bolts to appropriate length,
ush against the rose.
Fit self-tapping wood screws to each rose as necessary.
WARNING:
NOTE:
All applications involving door closers require 2x through-fixing screws
and 2x self-tapping wood screws to be fitted to each rose.
Failure to do so may void manufacturing warranty.
DOOR PREPARATION
A
When drilling through the door, drill from both sides to avoid
damaging the door.
B
Accurate door preparation is essential for the functioning of this lock.
Please follow the enclosed template and instructions carefully.
Through-bolt fixing is recommended.
Drill a 35mm hole through the door for privacy sets and a
C
20mm hole for passage sets.
Drill (2) 5mm holes through the door where through-bolt xing
is required.
Drill a 24mm hole x 85mm deep into the front edge of the
door.
Mark centre for either passage or privacy set.
Mark holes for through-bolt xing where required.
A
B
C
Fold template at correct height
(suggested height for centreline is 970mm from oor)
4
4
4
4
4
DRILL HOLES
Mark centre of door thickness on horizontal centreline.
3
3
3
3
3
1
1
1
1
1
2
2
2
2
2
P R E P AR E J AMB & INS TALL S TR IKE
INS TALL LAT C H
A
B
C
A
B
C
Insert latch into hole. Trace around face plate.
Chisel out wood until facepate ts ush with door edge.
Fasten latch to door so bevelled edge of latchbolt faces
jamb.
5
5
5
5
5
6
6
REMOVE ROSE CAPS
A
B
INSTALL FURNITURE
Mark vertical line and height centreline on jamb, exactly
opposite centre of latch.
Drill (2) 20mm holes x 15mm deep, 8mm above and below
height centreline.
Use strike plate as pattern for cutout. Chisel out and
install strike.
(Privacy Set Illustrated)
(Universal Strike Illustrated)
Insert spindles into furniture, as illustrated.
Attach furniture to door by through-bolt xing. Cut bolts to appropriate length,
ush against the rose.
Fit self-tapping wood screws to each rose as necessary.
NOTE:
All applications involving door closers require 2x through-fixing screws
and 2x self-tapping wood screws to be fitted to each rose.
Failure to do so may void manufacturers’ warranty.
DOOR PREPARATION
A
When drilling through the door, drill from both sides to avoid
damaging the door.
B
Accurate door preparation is essential for the functioning of this lock.
Please follow the enclosed template and instructions carefully.
Through-bolt fixing is recommended.
Drill a 35mm hole through the door for privacy sets and a
C
25mm hole for passage sets.
Drill 2x 5mm holes through the door where through-bolt xing
is required.
Drill a 24mm hole x 85mm deep into the front edge of the
door.
Mark centre for either passage or privacy set.
Mark holes for through-bolt xing where required.
A
B
C
Fold template at correct height
(suggested height for centreline is 970mm from oor)
4
4
4
4
4
DRILL HOLES
Mark centre of door thickness on horizontal centreline.
3
3
3
3
3
1
1
1
1
1
2
2
2
2
2
P R E P AR E J AMB & INS TALL S TR IK EINS T ALL LAT C H
A
B
C
A
B
C
Insert latch into hole. Trace around face plate.
Chisel out wood until facepate ts ush with door edge.
Fasten latch to door so bevelled edge of latchbolt faces
jamb.
5
5
5
5
5
6
6
REMOVE ROSE CAPS
A
B
INSTALL FURNITURE
Mark vertical line and height centreline on jamb, exactly
opposite centre of latch.
Drill 2x 20mm holes x 15mm deep, 8mm above and below
height centreline.
Use strike plate as pattern for cutout. Chisel out and install strike.
(Privacy Set illustrated)
(Universal Strike illustrated)
Insert spindles into furniture, as illustrated.
Attach furniture to door by through-bolt xing. Cut bolts to appropriate length,
ush against the rose.
Fit self-tapping wood screws to each rose as necessary.
NOTE:
All applications involving door closers require 2x through-fixing screws
and 2x self-tapping wood screws to be fitted to each rose.
Failure to do so may void manufacturers’ warranty.
DOOR PREPARATION
A
When drilling through the door, drill from both sides to avoid
damaging the door.
B
Accurate door preparation is essential for the functioning of this lock.
Please follow the enclosed template and instructions carefully.
Through-bolt fixing is recommended.
Drill a 35mm hole through the door for privacy sets and a
C
25mm hole for passage sets.
Drill 2x 5mm holes through the door where through-bolt xing
is required.
Drill a 24mm hole x 85mm deep into the front edge of the
door.
Mark centre for either passage or privacy set.
Mark holes for through-bolt xing where required.
A
B
C
Fold template at correct height
(suggested height for centreline is 970mm from oor)
4
4
4
4
4
DRILL HOLES
Mark centre of door thickness on horizontal centreline.
3
3
3
3
3
1
1
1
1
1
2
2
2
2
2
P R E P AR E J AMB & INS TALL S TR IK EINS T ALL LAT C H
A
B
C
A
B
C
Insert latch into hole. Trace around face plate.
Chisel out wood until facepate ts ush with door edge.
Fasten latch to door so bevelled edge of latchbolt faces
jamb.
5
5
5
5
5
6
6
REMOVE ROSE CAPS
A
B
INSTALL FURNITURE
Mark vertical line and height centreline on jamb, exactly
opposite centre of latch.
Drill 2x 20mm holes x 15mm deep, 8mm above and below
height centreline.
Use strike plate as pattern for cutout. Chisel out and install strike.
(Privacy Set illustrated)
(Universal Strike illustrated)
Insert spindles into furniture, as illustrated.
Attach furniture to door by through-bolt xing. Cut bolts to appropriate length,
ush against the rose.
Fit self-tapping wood screws to each rose as necessary.
A. 7000/9000 privacy sets have a plastic stop inserted on
each side to prevent the handle rotating upwards. This is only
required for models with square handles (to avoid privacy pin
breakage).
A.
Door Preparation Drill Holes
Install Latch
Prepare Jamb and Install Strike
Remove Rose Caps Install Furniture
Insert spindles into furniture, as illustrated.
Attach furniture to door by through-bolt xing. Cut bolts to
appropriate ush against the rose. Fit self-tapping wood screws to each
rose as necessary.
A
B
6
5
4
3
2
7000/9000 and Medio Series
Installation Instructions
6000/8000 Series
Installation Instructions
8
8
8
8
8
7
7
7
7
7
ATTAC H P R IVAC Y BUT T ONR E P LAC E R OS E C AP S
A
B
AReplace rose caps
Insert black plastic plug into hole, on outside rose.
Screw in privacy button for privacy sets.
TO HAND THE LATCH
1
1
1
1
1
FOLD HERE ON EDGE OF DOOR
PRIVACY LATCHBOLT HANDING INSTRUCTIONS
All Privacy Latchbolts are supplied handed to accomodate inward opening doors. If you have an
outward opening door, use the following instructions to hand the latchbolt correctly.
For Privacy Set
55mm backset
mark centre for
35mm hole at a
Mark center of door &
drill 24mm diameter x
85mm deep hole
Mark centre for
5mm throug h
Mark centre for
5mm through
For Passage Set
mark centre for
60mm backset
20mm hole at a
PASSAGE/PRIVACY SET INSTALLATION GUIDE
Important - Double check dimensions if printing from an electronic version
A
(Privacy Sets Only)
Remove Forend and rotate the latch head. Replace Forend to set in place.
Reference: ZPIC
Replace Rose Caps Attach Privacy Button
Privacy Latchbolt Handing Instructions
Passage/Privacy Set Installation Guide
7 8
Allegion (New Zealand) Limited
Phone 0800 477 869
Website www.allegion.co.nz
Allegion (Australia) Pty Ltd
Phone 1800 098 094
Website www.allegion.com.au
08/2017 ZPIC
-
1
-
2
ALLEGION SCHLAGE 7000 SERIES Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Ideal Security Inc. SKDXSS Installation guide
-
IDEAL Security SK1994W Installation guide
-
First Watch Security 1853 Installation guide
-
Sure-Loc Hardware JU102 26 Installation guide
-
Premier Lock EL03 Installation guide
-
Cal-Royal NM Series NM8040-SS Extra Heavy Duty Mortise Locks User manual
-
Jigtech LAL0863 Operating instructions
-
Brink's Home Security 22022-119-4 Installation guide
-
sylvan E71 Operating instructions
-
Gainsborough TradePro Lever Dummy Trim Installation guide
