Catalyst 6800 Ethernet Module Installation Guide
First Published: December 23, 2013
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are
encouraged to try to correct the interference by using one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version
of the UNIX operating system. All rights reserved. Copyright
©
1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED "AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: http://
www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1110R)
©
2015 Cisco Systems, Inc. All rights reserved.
CONTENTS
Preface
Preface v
Document Conventions v
Related Documentation vii
Obtaining Documentation and Submitting a Service Request vii
CHAPTER 1
Ethernet Switching Modules Overview 1
10/100/1000 Copper Ethernet Modules 1
C6800-48P-TX and C6800-48P-TX-XL Ethernet Modules 1
1-Gigabit Pluggable Ethernet Modules 4
C6800-48P-SFP and C6800-48P-SFP-XL Ethernet Modules 4
10-Gigabit Pluggable Ethernet Modules 6
C6800-8P10G and C6800-8P10G-XL Ethernet Modules 6
C6800-16P10G and C6800-16P10G-XL Ethernet Modules 10
C6800-32P10G and C6800-32P10G-XL Ethernet Modules 13
CHAPTER 2
Preparing for Installation 17
Safety Warnings 17
Preventing Electrostatic Discharge Damage 18
Establishing System Ground 18
Attaching an ESD Strap 21
Tools Required for Module Installation or Removal 23
CHAPTER 3
Installing and Removing Modules, Transceivers, and Attaching Cables 25
Installing and Removing Ethernet Switching Modules 25
Installing an Ethernet Switching Module 25
Removing and Ethernet Module 30
Installing Transceivers and Module Connectors 31
Catalyst 6800 Ethernet Module Installation Guide
iii
Attaching Network Interface Cables 31
Attaching Optical Network Interface Cables 31
Mode-Conditioning Patch Cord 32
Installing the Patch Cord 33
Connecting Transceivers to a Copper Network 34
Verifying the Installation 34
Verifying Newly Installed Modules 34
Example: show module Command Output for C6800-48P-TX-XL 34
Example: show module Command Output for C6800-48P-SFP 35
APPENDIX A
Module Specifications 37
10/100/1000 Ethernet Module Specifications 37
C6800-48P-TX and C6800-48P-TX-XL Specifications 37
1-Gigabit Ethernet Module Specifications 38
C6800-48P-SFP and C6800-48P-SFP-XL Module Specifications 38
10-Gigabit Ethernet Module Specifications 40
C6800-8P10G and C6800-8P10G-XL Module Specifications 40
C6800-16P10G and C6800-16P10G-XL Module Specifications 41
C6800-32P10G and C6800-32P10G-XL Module Specifications 43
APPENDIX B
LEDs 45
Ethernet Module LEDs 45
APPENDIX C
Pluggable Transceivers, Module Connectors 47
Pluggable Transceivers 47
1-GB Transceivers 47
10-GB Transceivers 48
WDM Transceivers 49
Module Connectors 51
RJ-45 Connector 52
SC Connector 52
LC Connector 53
Catalyst 6800 Ethernet Module Installation Guide
iv
Contents
Preface
•
Document Conventions, page v
•
Related Documentation, page vii
•
Obtaining Documentation and Submitting a Service Request, page vii
Document Conventions
This document uses the following conventions:
DescriptionConvention
Both the ^ symbol and Ctrl represent the Control (Ctrl) key on a keyboard. For
example, the key combination ^D or Ctrl-D means that you hold down the Control
key while you press the D key. (Keys are indicated in capital letters but are not
case sensitive.)
^ or Ctrl
Commands and keywords and user-entered text appear in bold font.bold font
Document titles, new or emphasized terms, and arguments for which you supply
values are in italic font.
Italic font
Terminal sessions and information the system displays appear in courier font.Courier font
Bold Courier font indicates text that the user must enter.Bold Courier font
Elements in square brackets are optional.[x]
An ellipsis (three consecutive nonbolded periods without spaces) after a syntax
element indicates that the element can be repeated.
...
A vertical line, called a pipe, indicates a choice within a set of keywords or
arguments.
|
Optional alternative keywords are grouped in brackets and separated by vertical
bars.
[x | y]
Catalyst 6800 Ethernet Module Installation Guide
v
DescriptionConvention
Required alternative keywords are grouped in braces and separated by vertical
bars.
{x | y}
Nested set of square brackets or braces indicate optional or required choices
within optional or required elements. Braces and a vertical bar within square
brackets indicate a required choice within an optional element.
[x {y | z}]
A nonquoted set of characters. Do not use quotation marks around the string or
the string will include the quotation marks.
string
Nonprinting characters such as passwords are in angle brackets.< >
Default responses to system prompts are in square brackets.[ ]
An exclamation point (!) or a pound sign (#) at the beginning of a line of code
indicates a comment line.
!, #
Reader Alert Conventions
This document may use the following conventions for reader alerts:
Means reader take note. Notes contain helpful suggestions or references to material not covered in the
manual.
Note
Means the following information will help you solve a problem.
Tip
Means reader be careful. In this situation, you might do something that could result in equipment damage
or loss of data.
Caution
Means the described action saves time. You can save time by performing the action described in the
paragraph.
Timesaver
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with
standard practices for preventing accidents. Use the statement number provided at the end of each warning
to locate its translation in the translated safety warnings that accompanied this device. Statement 1071
SAVE THESE INSTRUCTIONS
Warning
Catalyst 6800 Ethernet Module Installation Guide
vi
Preface
Document Conventions
Related Documentation
Before installing or upgrading, refer to the Release Notes for Cisco IOS Release 15.1SY.
Note
•
Regulatory Compliance and Safety Information for the Catalyst 6800 Series Ethernet Modules located
at: Regulatory Compliance and Safety Information for the Catalyst 6800 Series Switches
• Cisco Catalyst 6807-XL Switch documentation located at: http://www.cisco.com/go/cat6800_docs
• Cisco Catalyst 6500 Series Switches documentation located at: http://www.cisco.com/go/cat6500_docs
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information,
see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco
technical documentation, at:
http://www.cisco.com/c/en/us/td/docs/general/whatsnew/whatsnew.html
Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed
and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free
service and Cisco currently supports RSS version 2.0.
Catalyst 6800 Ethernet Module Installation Guide
vii
Preface
Related Documentation
Catalyst 6800 Ethernet Module Installation Guide
viii
Preface
Obtaining Documentation and Submitting a Service Request
CHAPTER 1
Ethernet Switching Modules Overview
•
10/100/1000 Copper Ethernet Modules, page 1
•
1-Gigabit Pluggable Ethernet Modules, page 4
•
10-Gigabit Pluggable Ethernet Modules, page 6
10/100/1000 Copper Ethernet Modules
C6800-48P-TX and C6800-48P-TX-XL Ethernet Modules
C6800-48P-TX and C6800-48P-TX-XL Ethernet modules provide 48 10/100/1000-Mbps full- or half-duplex
ports.
Figure 1: C6800-48P-TX and C6800-48P-TX-XL Ethernet Module Front Panel
Even numbered ports3Status LED1
RFID4Odd numbered ports2
The sticker on the module faceplate identifies it as either a C6800-48P-TX or a C6800-48P-TX-XL depending
on whether a WS-F6K-DFC4-A or WS-F6K-DFC4-AXL daughter card is installed on the module.
Catalyst 6800 Ethernet Module Installation Guide
1
Table 1: C6800-48P-TX and C6800-48P-TX-XL Ethernet Module Features
DescriptionFeature
•
48 ports, numbered left to right and top to bottom
•
4 port groups. Port ranges per port group:
•
1 to 12
•
13 to 24
•
25 to 36
•
37 to 48
Ports per module
RJ 45Port connector type
328 ft (100 m) over Category 5, 5e, and 6 UTP/STP cableCabling distance
1.5 MB per port.
18 MB per port group.
Buffer size
•
Number of egress queues: 4
•
Number of ingress queues: 2
•
Number of thresholds per egress queue: 1 or 2
•
Number of thresholds per ingress queue: 8
QoS
Up to 9216 bytes per frameMaximum frame size
1.2:1Module oversubscription rate
Supervisor Engine 2T-10GESupervisor engine support
With Supervisor Engine 2T-10GE —Cisco IOS Release
15.2(1)SY or later
Software support
With a WS-F6K-DFC4-A / AXL daughter card:
• Tx—1p3q8t
• Rx—2q8t
Queues per port
Catalyst 6800 Ethernet Module Installation Guide
2
Ethernet Switching Modules Overview
C6800-48P-TX and C6800-48P-TX-XL Ethernet Modules
DescriptionFeature
C6800-48P-TX/ TX-XL operates only in a Cisco Catalyst
6807-XL and a Cisco Catalyst 6500 E-series chassis equipped
with a Supervisor Engine 2T-10GE.
Modules must be installed in adjacent slots. To maintain
adequate air flow through the chassis, install a
switching-module filler plate (Cisco part number
WS-X6K-SLOT-CVR-E=) in unused slots, rather than a blank
slot cover (Cisco part number WS-X6K-SLOT-CVR=).
Chassis and slot restrictions
Dual switch-fabric connections:
• Fabric channel 1—Ports 25 to 48.
• Fabric channel 2—Ports 1 to 24.
Fabric connection
20 Gb/secFabric channel speed
PoE— Not supported.
Distributed forwarding support— C6800-48P-TX ships with
a factory-installed DFC4-A and C6800-48P-TX-XL ships with
a factory-installed DFC4-AXL daughter card installed. The
modules are not field upgradable.
Module upgrade availability
Not supported.Pluggable transceivers
Supported.TDR support
Related Topics
Installing an Ethernet Switching Module, on page 25
C6800-48P-TX and C6800-48P-TX-XL Specifications, on page 37
Ethernet Module LEDs, on page 45
Example: show module Command Output for C6800-48P-TX-XL , on page 34
Catalyst 6800 Ethernet Module Installation Guide
3
Ethernet Switching Modules Overview
C6800-48P-TX and C6800-48P-TX-XL Ethernet Modules
1-Gigabit Pluggable Ethernet Modules
C6800-48P-SFP and C6800-48P-SFP-XL Ethernet Modules
C6800-48P-SFP and C6800-48P-SFP-XL Ethernet modules provide 48 1-Gbps full- or half-duplex ports.
Figure 2: C6800-48P-SFP and C6800-48P-SFP-XL Ethernet Module Front Panel
Even numbered ports3Status LED1
RFID4Odd numbered ports2
The sticker on the module faceplate identifies it as either a C6800-48P-SFP and C6800-48P-SFP-XL depending
on whether a WS-F6K-DFC4-A or WS-F6K-DFC4-AXL daughter card is installed on the module.
Table 2: C6800-48P-SFP and C6800-48P-SFP-XL Ethernet Module Features
DescriptionFeature
48 ports. Ports are numbered left to right and top to bottom.
4 port groups. Port ranges per port group:
•
1 to 12
•
13 to 24
•
25 to 36
•
37 to 48
Ports per module
LC (optical) or RJ-45 (copper) depending on the SFP transceiver
installed.
Port connector type
Catalyst 6800 Ethernet Module Installation Guide
4
Ethernet Switching Modules Overview
1-Gigabit Pluggable Ethernet Modules
DescriptionFeature
Depends on the SFP transceiver installed in the module port.
For cabling distance information, refer to the installation guides
for Cisco Transceiver Modules at: Install and Upgrade Guides
Cabling distance
1.5 MB per port
18 MB per port group
Buffer size
Number of egress queues—4
Number of ingress queues—2
Number of thresholds per egress queue—1 or 2
Number of thresholds per ingress queue—8
QoS
Up to 9216 bytes per frameMaximum frame size
1.2:1Module oversubscription rate
Supervisor Engine 2T-10GESupervisor engine support
With Supervisor Engine 2T-10GE —Cisco IOS Release
15.2(1)SY or later
Software support
With a WS-F6K-DFC4-A / AXL daughter card:
• Tx—1p3q8t
• Rx—2q8t
Queues per port
C6800-48P-SFP/ SFP-XL operates only in a Cisco Catalyst
6807-XL and a Cisco Catalyst 6500 E-series chassis equipped
with a Supervisor Engine 2T-10GE.
Modules must be installed in adjacent slots. To maintain adequate
air flow through the chassis, install a switching-module filler
plate (Cisco part number WS-X6K-SLOT-CVR-E=) in unused
slots, rather than a blank slot cover (Cisco part number
WS-X6K-SLOT-CVR=).
Chassis and slot restrictions
Dual switch-fabric connections:
• Fabric channel 1—Even ports 2 to 48.
• Fabric channel 2—Odd ports 1 to 47.
Fabric connection
20 Gb/secFabric channel speed
Catalyst 6800 Ethernet Module Installation Guide
5
Ethernet Switching Modules Overview
C6800-48P-SFP and C6800-48P-SFP-XL Ethernet Modules
DescriptionFeature
PoE support—Not supported.
Distributed forwarding support— C6800-48P-SFP ships with a
factory-installed DFC4-A and C6800-48P-SFP-XL ships with
a factory-installed DFC4-AXL daughter card. The modules are
not field upgradable.
Module upgrade availability
For SFP transceivers currently supported, refer to the Cisco
Transceiver Modules compatibility matrices at: Compatibility
Information
Pluggable transceivers
DOM is hardware ready.Digital Optical Monitoring (DOM) support
Related Topics
Installing an Ethernet Switching Module, on page 25
C6800-48P-SFP and C6800-48P-SFP-XL Module Specifications, on page 38
Ethernet Module LEDs, on page 45
Example: show module Command Output for C6800-48P-SFP , on page 35
10-Gigabit Pluggable Ethernet Modules
C6800-8P10G and C6800-8P10G-XL Ethernet Modules
The C6800-8P10G and C6800-8P10G-XL Ethernet modules provide eight 10G or eight 1G full-duplex
transceiver ports.
Figure 3: C6800-8P10G-XL Ethernet Module Front Panel
Port group ID4Status and ID LEDs1
Port number540G port IDs
1
2
RFID610G ports (A total of two port groups)3
Catalyst 6800 Ethernet Module Installation Guide
6
Ethernet Switching Modules Overview
10-Gigabit Pluggable Ethernet Modules
1
40G ports are currently not supported
The sticker on the module faceplate identifies it as either a C6800-8P10G or a C6800-8P10G-XL depending
on whether a WS-F6K-DFC4-E or WS-F6K-DFC4-EXL daughter card is installed on the module.
Table 3: C6800-8P10G and C6800-8P10G-XL Ethernet Module Features
DescriptionFeature
• 8 ports—Eight 1G ports, or eight 10G ports.
•
Ports are numbered left to right.
•
2 port groups. Port ranges per port group:
•
1 to 4
•
5 to 8
Ports per module
LC (optical) or RJ-45 (copper) depending on the SFP transceiver
installed.
Port connector type
Depends on the SFP transceiver installed in the module port. For
cabling distance information, refer to the installation guides for
Cisco Transceiver Modules at: Install and Upgrade Guides
Cabling distance
Ingress buffer size:
•
2.5 MB per port
•
10 MB per port group
• Total—40 MB
Egress buffer size:
•
500 MB per port
•
2 GB per port group
• Total—8 GB
Buffer size
• Number of egress queues—8
• Number of ingress queues—8
• Number of thresholds per egress queue—4
• Number of thresholds per ingress queue—4
QoS
Up to 9216 bytes per frameMaximum frame size
Catalyst 6800 Ethernet Module Installation Guide
7
Ethernet Switching Modules Overview
C6800-8P10G and C6800-8P10G-XL Ethernet Modules
DescriptionFeature
1:1 (When all eight 10G ports are used.)Module oversubscription rate
Supervisor Engine 2T-10GESupervisor engine support
With Supervisor Engine 2T-10GE —Cisco IOS Release 15.2(1)SY
or later
Software support
With a WS-F6K-DFC4-E/ EXL daughter card:
• Tx—1p7q4t
• Rx—1p7q4t
Queues per port
The following restrictions apply to module installation and
operation:
• Module installation—Modules must be installed in adjacent
slots. To maintain adequate air flow through the chassis,
install a switching-module filler plate (Cisco part number
WS-X6K-SLOT-CVR-E=) in unused slots, rather than a
blank slot cover (Cisco part number
WS-X6K-SLOT-CVR=).
• Module operation—The C6800-8P10G/ 10G-XL operates
only in a Cisco Catalyst 6807-XL and a Cisco Catalyst 6500
E-series chassis equipped with a Supervisor Engine
2T-10GE.
• Slot restrictions—In the following switch chassis, you
cannot install Ethernet modules in slots meant for supervisor
engines:
•
In a Cisco Catalyst 6807-XL, the supervisor engine
slots are 3 and 4.
•
In a Cisco Catalyst 6513 E-series chassis, the
supervisor engine slots are 7 and 8. This restriction
does not apply to any other 6500 E-series chassis.
Chassis and slot restrictions
For Cisco Catalyst 6807-XL switches:
•
Fabric channel 0 : Ports 1 to 4
•
Fabric channel 1: Ports 5 to 8
For Cisco Catalyst 6500-E series switches:
•
Fabric channel 0 : Ports 1 to 4
•
Fabric channel 1: Ports 5 to 8
Fabric connection
Catalyst 6800 Ethernet Module Installation Guide
8
Ethernet Switching Modules Overview
C6800-8P10G and C6800-8P10G-XL Ethernet Modules
DescriptionFeature
In a Cisco Catalyst 6807-XL chassis—80 GB per second
In a Cisco Catalyst 6500-E series chassis—80 GB per second
Fabric channel speed
PoE—Not supported
Distributed forwarding support— The C6800-8P10G module
ships with a factory-installed DFC4-E and the C6800-8P10G-XL
module ships with a factory-installed DFC4-EXL daughter card.
The modules are not field upgradable.
Module upgrade availability
These Ethernet modules support 10G SFP+ modules and 1G SFP
modules. For SFP transceivers currently supported, refer to the
Cisco Transceiver Modules compatibility matrices at:
Compatibility Information.
Pluggable transceivers support
Supported with GLC-T (1G Copper SFP) transceiversTDR support
Supported with select 1G and 10G Fiber SFP/SFP+ transceivers.
• The DOM-supported 1G transceivers are—GLC-BX-U,
GLC-BX-D, GLC-SX-MMD, GLC-EX-SMD,
GLC-LH-SMD, GLC-ZX-SMD, SFP-DWDM.
•
The DOM-supported 10G Fiber SFP/SFP+ transceivers are
listed at Cisco Digital Optical Monitoring Compatibility
Matrix.
Digital Optical Monitoring (DOM)
support
Related Topics
Installing an Ethernet Switching Module, on page 25
C6800-8P10G and C6800-8P10G-XL Module Specifications, on page 40
Ethernet Module LEDs, on page 45
Catalyst 6800 Ethernet Module Installation Guide
9
Ethernet Switching Modules Overview
C6800-8P10G and C6800-8P10G-XL Ethernet Modules
C6800-16P10G and C6800-16P10G-XL Ethernet Modules
The C6800-16P10G and C6800-16P10G-XL Ethernet modules provide sixteen 10G or sixteen 1G transceiver
ports.
Figure 4: C6800-16P10G-XL Ethernet Module Front Panel
Port group ID4Status and ID LEDs1
Port number540G port IDs
2
2
RFID610G ports (A total of four port groups)3
2
40G ports are currently not supported
The sticker on the module faceplate identifies it as either a C6800-16P10G or a C6800-16P10G-XL depending
on whether a WS-F6K-DFC4-E or WS-F6K-DFC4-EXL daughter card is installed on the module.
Table 4: C6800-16P10G and C6800-16P10G-XL Ethernet Module Features
DescriptionFeature
• 16 ports—Sixteen 1G ports, or sixteen 10G ports.
•
Ports are numbered left to right.
•
2 port groups. Port ranges per port group:
•
1 to 8
•
9 to 16
Ports per module
LC (optical) or RJ-45 (copper) depending on the SFP transceiver
installed.
Port connector type
Depends on the SFP transceiver installed in the module port. For
cabling distance information, refer to the installation guides for
Cisco Transceiver Modules at: Install and Upgrade Guides
Cabling distance
Catalyst 6800 Ethernet Module Installation Guide
10
Ethernet Switching Modules Overview
C6800-16P10G and C6800-16P10G-XL Ethernet Modules
DescriptionFeature
Ingress buffer size:
• Per port (over subscription mode)—1.25 MB
• Per port (transparent mode)—2.5 MB
•
10 MB per port-group
• Total—40 MB
Egress buffer size:
• Per port (over subscription mode)—250 MB
• Per port (transparent mode)—500 MB
•
2 GB per port-group
• Total—8 GB
Buffer size
•
Number of egress queues: 8
•
Number of ingress queues: 8
•
Number of thresholds per egress queue: 4
•
Number of thresholds per ingress queue: 4
QoS
Up to 9216 bytes per frameMaximum frame size
2:1 (When all sixteen 10G ports are used.)Module oversubscription rate
Supervisor Engine 2T-10GESupervisor engine support
With Supervisor Engine 2T-10GE —Cisco IOS Release 15.2(1)SY
or later
Software support
With a WS-F6K-DFC4-E/ EXL daughter card:
• Tx—1p7q4t
• Rx—2p6q4t
Queues per port
Catalyst 6800 Ethernet Module Installation Guide
11
Ethernet Switching Modules Overview
C6800-16P10G and C6800-16P10G-XL Ethernet Modules
DescriptionFeature
The following restrictions apply to module installation and
operation:
• Module installation—Modules must be installed in adjacent
slots. To maintain an adequate air flow through the chassis,
install a switching-module filler plate (Cisco part number
WS-X6K-SLOT-CVR-E=) in unused slots, rather than a
blank slot cover (Cisco part number
WS-X6K-SLOT-CVR=).
• Module operation—C6800-16P10G/ 10G-XL operates only
in a Cisco Catalyst 6807-XL and a Cisco Catalyst 6500
E-series chassis equipped with a Supervisor Engine
2T-10GE.
• Slot restrictions—In the following switch chassis, you
cannot install Ethernet modules in slots meant for supervisor
engines:
•
In a Cisco Catalyst 6807-XL, the supervisor engine
slots are 3 and 4.
•
In a Cisco Catalyst 6513 E-series chassis, the
supervisor engine slots are 7 and 8. This restriction
does not apply to any other 6500 E-series chassis.
Chassis and slot restrictions
For Cisco Catalyst 6807-XL switches:
•
Fabric channel 0 : Ports 1 to 8
•
Fabric channel 1: Ports 9 to 16
For Cisco Catalyst 6500-E series switches:
•
Fabric channel 0 : Ports 1 to 8
•
Fabric channel 1: Ports 9 to 16
Fabric connection
In a Cisco Catalyst 6807-XL chassis—80 GB per second
In a Cisco Catalyst 6500-E series chassis—80 GB per second
Fabric channel speed
PoE—Not supported
Distributed forwarding— The C6800-16P10G module ships with
a factory-installed DFC4-E and the C6800-16P10G-XL module
ships with a factory-installed DFC4-EXL daughter card. The
modules are not field upgradable.
Module upgrade availability
Catalyst 6800 Ethernet Module Installation Guide
12
Ethernet Switching Modules Overview
C6800-16P10G and C6800-16P10G-XL Ethernet Modules
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/