Cisco Systems 3010 User manual

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

Cisco IE 3010 Switch Hardware Installation

Guide

Revised October 12, 2012

Text Part Number: 78-19581-02

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL

STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT

WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT

SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE

OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required

to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be

determined by turning the equipment off and on, users are encouraged to try to correct the interference by using one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH

ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR

IMPLIED, INCLUDING, WITHOUT

LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF

DEALING, USAGE, OR TRADE PRACTICE.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this

URL:

www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership

relationship between Cisco and any other company. (1110R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the

document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Cisco IE 3010 Switch Hardware Installation Guide

iii

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

CONTENTS

Preface vii

Related Publications i-viii

Obtaining Documentation and Submitting a Service Request i-viii

CHAPTER

1 Product Overview 1-1

Switch Models 1-1

Cable Side 1-2

10/100 Fast Ethernet Ports 1-3

PoE Ports 1-3

Dual-Purpose Ports 1-4

SFP Modules 1-5

SFP Module Patch Cable 1-6

Power-Input Terminal 1-6

Alarm Ports 1-6

Alarm Input 1-7

Alarm Output 1-7

Management Ports 1-7

LEDs 1-8

Switch Panel LEDs 1-8

System LED 1-9

Power-Supply Module LEDs 1-9

Alarm LEDs 1-9

Console LEDs 1-10

Port LEDs 1-10

PoE LED 1-11

Dual-Purpose Port LEDs 1-11

SD Flash Memory Card LED 1-11

SD Flash Memory Card 1-11

Power-Supply Side 1-12

Power-Supply Side LEDs 1-13

Power Supply Features 1-14

Management Options 1-14

Network Configurations 1-14

Contents

iv

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

CHAPTER

2 Switch Installation 2-1

Warnings 2-1

Installation Guidelines 2-3

Verifying Switch Operation 2-3

Installing the Switch 2-4

Rack-Mounting 2-4

Attaching Brackets for 19-Inch Racks 2-5

Attaching Brackets for 19-Inch Racks for IP-30 Compliance (Optional) 2-6

Attaching Brackets for 23-Inch Racks 2-12

Attaching Brackets for ETSI Racks 2-13

Rack-Mounting the Switch 2-14

Wall-Mounting 2-15

Attaching Brackets 2-16

Attaching Brackets for IP-30 Compliance (Optional) 2-16

Wall-Mounting the Switch 2-18

Installing and Removing SFP Modules 2-20

Installing SFP Modules 2-20

Removing SFP Modules 2-21

Inserting and Removing the SFP Module Patch Cable 2-21

Removing the SFP Module Patch Cable 2-22

Replacing the SD Flash Memory Card 2-23

Connecting Devices to the Ethernet Ports 2-25

Connecting to the 10/100 and 10/100/1000 Ports 2-25

Connecting to the 10/100 PoE Ports 2-26

Where to Go Next 2-27

CHAPTER

3 Power Supply Installation 3-1

Power-Supply Modules 3-1

Power-Supply Module Installation 3-3

Installation Guidelines 3-3

Installing a Power-Supply Module 3-4

Equipment That You Need 3-4

Grounding the Switch 3-4

Installing the Power-Supply Module in the Switch 3-6

Wiring the Power Source 3-7

Removing the Power-Supply Module 3-12

Contents

v

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

CHAPTER

4 Troubleshooting 4-1

Diagnosing Problems 4-1

Switch POST Results 4-1

Switch LEDs 4-2

Switch Connections 4-2

Bad or Damaged Cable 4-2

Ethernet and Fiber-Optic Cables 4-2

Link Status 4-2

10/100 and 10/100/1000 Port Connections 4-3

10/100 PoE Port Connections 4-3

SFP Module 4-3

Interface Settings 4-3

Ping End Device 4-3

Spanning Tree Loops 4-4

Switch Performance 4-4

Speed, Duplex, and Autonegotiation 4-4

Autonegotiation and Network Interface Cards 4-4

Cabling Distance 4-4

Resetting the Switch to the Factory Default Settings 4-5

Finding the Switch Serial Number 4-5

APPENDIX

A Technical Specifications A-1

Switch Specifications A-1

Power-Supply Module Specifications A-4

Alarm Ratings A-5

APPENDIX

B Connector and Cable Specifications B-1

Connector Specifications B-1

10/100 B-1

SFP Module Connectors B-2

Dual-Purpose Ports B-3

Alarm Port B-3

Cables and Adapters B-4

SFP Module Cables B-4

Cable Pinouts B-6

Console Port Adapter Pinouts B-7

Contents

vi

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

APPENDIX

C Configuring the Switch with the CLI Setup Program C-1

Accessing the CLI Through the Console Port C-1

RJ-45 Console Port C-1

USB Console Port C-3

Installing the Cisco Microsoft Windows USB Device Drivers C-4

Installing the Cisco Microsoft Windows XP USB Driver C-4

Installing the Cisco Microsoft Windows 2000 USB Driver C-4

Installing the Cisco Microsoft Windows Vista USB Driver C-5

Uninstalling the Cisco Microsoft Windows USB Drivers C-5

Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver C-5

Uninstalling the Cisco Microsoft Windows Vista USB Driver C-6

Entering the Initial Configuration Information C-7

IP Settings C-7

Completing the Setup Program C-7

I

NDEX

vii

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

Preface

This guide describes the hardware features of the Cisco Industrial Ethernet (IE) 3010 switch. It describes

the physical and performance characteristics of the switch, explains how to install it, and provides

troubleshooting information.

This guide does not describe system messages that you might receive or how to configure your switch.

See the switch software configuration guide, the switch command reference, and the switch system

message guide on Cisco.com:

http://www.cisco.com/go/IE3010_docs

Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in

this manual.

Caution Means reader be careful. In this situation, you might do something that could result in equipment

damage or loss of data.

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar

with standard practices for preventing accidents. Use the statement number provided at the end of

each warning to locate its translation in the translated safety warnings that accompanied this

device.

Statement 1071

SAVE THESE INSTRUCTIONS

viii

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

Preface

Related Publications

The safety warnings for this product are translated into several languages in the Regulatory Compliance

and Safety Information for the Cisco IE 3010 Switch that ships with the product on the documentation

CD. The EMC regulatory statements are also included in that guide.

Related Publications

http://www.cisco.com/go/IE3010_docs

Note Before installing, configuring, or upgrading the switch, see the release notes on Cisco.com for

the latest information.

• Release Notes for the Cisco IE 3010 Switch

• Cisco IE 3010 Switch Getting Started Guide

• Regulatory Compliance and Safety Information for the Cisco IE 3010 Switch

• Cisco IE 3010 Switch Software Configuration Guide

• Cisco IE 3010 Switch Command Reference

• Cisco IE 3010 Switch System Message Guide

Cisco SFP documents:

http://www.cisco.com/en/US/products/hw/modules/ps5455/prod_installation_guides_list.html

SFP compatibility matrix documents:

http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional

information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and

revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed

and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free

service and Cisco currently supports RSS version 2.0.

CHAPTER

1-1

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

1

Product Overview

The Cisco IE 3010 switch provides a rugged and secure switching infrastructure for harsh environments.

It is suitable for industrial Ethernet applications, including process manufacturing, intelligent

transportation systems (ITSs), rail transportation, and other similar deployments.

In industrial environments, you can connect the switch to any Ethernet-enabled industrial

communication devices, including programmable logic controllers (PLCs), human-machine interfaces

(HMIs), drives, sensors, and input and output (IO) devices.

• Switch Models, page 1-1

• Cable Side, page 1-2

• Power-Supply Side, page 1-12

• Management Options, page 1-14

Switch Models

Table 1-1 Switch Models

Model Description

Cisco IE-3010-24TC 24 10/100 FastEthernet ports, 2 dual-purpose ports

(2 10/100/1000BASE-T copper ports and 2 SFP

1

module slots), and

2 AC and DC power-supply module slots.

1. SFP = small form-factor pluggable.

Cisco IE-3010-16S-8PC 16 100BASE-FX SFP-module slots; 8 10/100 FastEthernet PoE

2

ports,

2 dual-purpose ports (2 10/100/1000BASE-T copper ports and 2 SFP

module slots), and 2 AC and DC power-supply module slots.

2. PoE = Power over Ethernet.

1-2

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

Chapter 1 Product Overview

Cable Side

The 10/100 Fast Ethernet downlink ports in Figure 1-1 are grouped in pairs. The first member of the pair

(port 1) is above the second member (port 2) on the left. Port 3 is above port 4, and so on.

The

dual-purpose ports are numbered 1 and 2.

Figure 1-1 Cisco IE-3010-24TC Cable-Side View

1 SD

1

flash memory card slot

1. SD = Secure Digital

6 RJ-45 console port

2 LEDs 7 USB (mini-Type B) console port

3 Express Setup button 8 Power-input terminal

4 10/100 ports 9 Alarm port

5 Dual purpose ports

7

4 92

1 3 5 6 8

208362

Cisco IE 3010

1-3

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

Chapter 1 Product Overview

Cable Side

The100BASE-FX SFP ports and the 10/100 PoE ports are grouped in pairs. The first member of the pair

(port

1) is above the second member (port 2) on the left. Port 3 is above port 4, and so on.

The

dual-purpose ports are numbered 1 and 2.

Figure 1-2 Cisco IE-3010-16S-8PC Cable-Side View

10/100 Fast Ethernet Ports

You can set the 10/100 ports on the switch to operate in any combination of half duplex, full duplex, or

10 or 100 Mb/s. You can set the ports for speed and duplex autonegotiation. The default setting is

autonegotiate.

When set for autonegotiation, the switch determines the speed and duplex settings of the attached device

and advertises its own capabilities. If the connected device also supports autonegotiation, the switch

negotiates the best connection (the fastest line speed that both devices support and full-duplex

transmission if the attached device supports it) and configures itself accordingly. In all cases, the

attached device must be within 328 feet (100

meters).

PoE Ports

Warning

Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if

interconnections are made using uninsulated exposed metal contacts, conductors, or terminals.

Avoid using such interconnection methods, unless the exposed metal parts are located within a

restricted access location and users and service people who are authorized within the restricted

access location are made aware of the hazard. A restricted access area can be accessed only through

the use of a special tool, lock and key or other means of security.

Statement 1072

1 SD flash memory card slot 6 Dual purpose ports

2 LEDs 7 RJ-45 console port

3 Express Setup button 8 USB (mini-Type B) console port

4 100BASE-FX SFP ports 9 Power-input terminal

5 10/100 PoE ports 10 Alarm port

PO W ER

OVER

ET HER N ET

PO W ER

OVER

ET HER N ET

8

4

102

1 3 65 7 9

208363

Cisco IE 3010

1-4

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

Chapter 1 Product Overview

Cable Side

The 10/100 PoE ports on the Cisco IE-3010-16S-8PC switches provide PoE support for devices that are

compliant with IEEE 802.3af. The Cisco prestandard PoE is also supported for Cisco IP

Phones and

Cisco

Aironet Access Points. The PoE ports on the switch deliver up to 15.4 W of PoE. Any four of the

eight ports are designated as high priority PoE ports, while the other four ports are designated as low

priority PoE ports. When both the power-supply modules are installed, the system has enough power to

support all eight ports as PoE ports. In case one of the power-supply modules fails, the power to the low

priority PoE ports is dropped, while power to the high priority PoE ports remains uninterrupted.

On a per-port basis, you control whether or not a port automatically provides power when an IP phone

or an access point is connected.

The 10/100 PoE ports use RJ-45 connectors with Ethernet pinouts. The maximum cable length is 328

feet (100 meters). The 100BASE-TX and 1000BASE-T traffic requires Category

5, Category 5e, or

Category

6 unshielded twisted pair (UTP) cable. The 10BASE-T traffic can use Category 3 or

Category 4 UTP cable.

For information about configuring and monitoring PoE ports, see the switch software configuration

guide on Cisco.com.

For information about port connections and port specifications, see the “Connecting Devices to the

Ethernet Ports” section on page 2-25 and the “Connector and Cable Specifications” section on page B-1.

Note The output of the PoE circuit has been evaluated as a Limited Power Source (LPS) per IEC 60950-1.

Dual-Purpose Ports

You can configure the dual-purpose ports on the switch as either 10/100/1000 ports or as SFP-module

ports. You can set the 10/100/1000 ports to autonegotiate, or you can configure them as fixed 10, 100,

or 1000 Mb/s (Gigabit) Ethernet ports.

By default, the switch selects the medium for each dual-purpose port (10/100/1000BASE-T or SFP).

When a link is achieved on one media type, the switch disables the other media type until the active link

goes down. If links are active on both media, the SFP-module port has priority, but you can use the

media-type interface configuration command to manually designate the port as an RJ-45 port or an SFP

port.

You can configure the speed and duplex settings consistent with the selected media type. For information

on configuring interfaces, see the switch software configuration guide.

1-5

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

Chapter 1 Product Overview

Cable Side

SFP Modules

The switch Ethernet SFP modules provide connections to other devices. These field-replaceable

transceiver modules provide the uplink interfaces.The modules have LC connectors for fiber-optic

connections or RJ-45 connectors for copper connections. You can use any combination of the supported

SFP modules listed in

Table 1-2.

For information about SFP modules, see your SFP module documentation and the “Installing and

Removing SFP Modules” section on page 2-20. For cable specifications, see Appendix B, “SFP Module

Cables.”

Table 1-2 Maximum Operating Temperature

Type of SFP Module Model

Rugged and Industrial SFPs

–40 to 140°F (–40 to 60°C)

• GLC-SX-MM-RGD

• GLC-LX-SM-RGD

• GLC-FE-100LX-RGD

• GLC-FE-100FX-RGD

• GLC-ZX-SM-RGD

Commercial SFPs

32 to 113°F (0 to 45°C)

• GLC-BX-D with DOM support

• GLC-BX-U with DOM support

• GLC-FE-100LX

• GLC-FE-100BX-D

• GLC-FE-100BX-U

• GLC-FE-100FX

• GLC-FE-100EX

• GLC-FE-100ZX

• CWDM SFP with DOM support

Extended temperature SFPs

23 to 140°F (–5 to 60°C)

• SFP-GE-L with digital optical monitoring

(DOM) support

• SFP-GE-S with DOM support

• SFP-GE-Z with DOM support

• GLC-EX-SMD with DOM support

1-6

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

Chapter 1 Product Overview

Cable Side

SFP Module Patch Cable

The switch uses an SFP-module patch cable, a 0.5-meter, copper, passive cable with SFP module

connectors at each end (see Figure 1-3). The patch cable connects two switches in a cascaded

configuration.

Figure 1-3 SFP-Module Patch Cable

See the “Inserting and Removing the SFP Module Patch Cable” section on page 2-21 for information

about using the SFP module patch cable.

You can order this cable (part number CAB-SFP-50CM=).

Power-Input Terminal

The power-input terminal provides screw terminals for the AC and DC power connections. The switch

can operate with one or two power supplies. If one of the power sources fail, the other continues to power

the switch. See

Chapter 3, “Power Supply Installation,” for information.

Figure 1-4 Power-Input Terminal

Alarm Ports

The switch has four alarm inputs and one alarm output. The alarm setting is open or closed.

• Open means that the normal condition has current flowing through the contact (referred to as a

normally closed contact). The alarm is generated when the current stops.

• Closed means that no current flows through the contact (referred to as a normally open contact). The

alarm is generated when the current flows.

126809

208415

1-7

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

Chapter 1 Product Overview

Cable Side

Alarm Input

The alarm input is a dry-contact alarm port. You can connect up to four alarm inputs from devices, such

as a door, a temperature gauge, or a fire alarm, to the alarm port. You can use the CLI to set the alarm

severity to minor, major, or critical. An alarm generates a system message and turns on an LED. See the

“Alarm LEDs” section on page 1-9 for the LED descriptions.

Alarm Output

The alarm output can be configured as a minor or major alarm. Output alarms often control an external

alarm, such as a bell or a light. To connect an external alarm device to the relay, you connect two relay

contact wires to complete the electrical circuit. See

Figure B-4 on page B-3 for information on the alarm

pinouts.

Management Ports

You can connect the switch to a PC running Microsoft Windows or to a terminal server through either

the RJ-45 console port or the USB console port.

• RJ-45 console port. The RJ-45 connection uses an RJ-45-to-DB-9 female cable.

• USB mini-Type B console port (5-pin connector). The USB connection uses a USB Type A-to-5-pin

mini-Type B cable.

The USB console interface speeds are the same as the RJ-45 console interface speeds.

To use the USB console port, you must install the Cisco Windows USB device driver on the device that

is connected to the USB console port (device running with Microsoft Windows).

Note For information about downloading the Cisco USB device driver, see the “Installing the Cisco Microsoft

Windows USB Device Drivers” section on page C-4.

With the Cisco Windows USB device driver, connecting and disconnecting the USB cable from the

console port does not affect Windows HyperTerminal operations. Mac OS X or Linux require no special

drivers.

Note The 5-pin mini-Type B connectors resemble the 4-pin mini-Type B connectors. They are not compatible.

Use only the 5-pin mini-Type B. See Figure 1-5.

Figure 1-5 USB Mini-Type B Port

The configurable inactivity timeout reactivates the RJ-45 console port if the USB console port is

activated, but no input activity occurs on it for a specified time period. When the USB console port

deactivates due to a timeout, you can restore its operation by disconnecting and reconnecting the USB

cable. For information on using the CLI to configure the USB console interface, see the switch software

guide.

253163

1-8

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

Chapter 1 Product Overview

Cable Side

LEDs

You can use the switch system and port LEDs to monitor switch activity and performance.

Switch Panel LEDs

Figure 1-6 Switch LEDs (Cable Side)

1 SYS (system) 9 OUT (alarm output)

2 CON (RJ-45 console) 10 PSU1 (power supply 1)

3 USB (mini-USB console) 11 PSU2 (power supply 2)

4 SD (SD flash memory card) 12 PoE

1

1. Only on the Cisco IE-3010-16S-8PC switch.

5 IN1 (alarm input 1) 13 Express Setup button

6 IN2 (alarm input 2) 14 Ethernet ports

7 IN3 (alarm input 3) 15 SFP module port

8 IN4 (alarm input 4) 16 10/100/1000 port

207198

21 3 45678 9 10 11 12 13

14 15

16

1-9

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

Chapter 1 Product Overview

Cable Side

System LED

Power-Supply Module LEDs

The switch power-supply module LEDs are labeled PSU1 and PSU2 (on the switch) and PSU OK (on

the power-supply module). They show whether power-supply modules 1 and 2 are receiving power. See

Figure 1-6 and Figure 1-9.

Alarm LEDs

Table 1-3 System LED

Color System Status

Off System is not powered on.

Blinking green POST

1

is in progress.

1. POST = power-on self-test.

Green System is operating normally.

Amber System is receiving power but is not functioning properly.

Table 1-4 Power-Supply Module LEDs

Color System Status

Off Power-supply module (1 or 2) is not installed.

Green Valid input is present, and the output is within the operating range.

Red Valid input is present, and the output is outside the operating range or is not present.

Blinking red Valid input is not present.

Table 1-5 Alarm Input LEDs

Color System Status

Off No alarm

Amber Minor alarm

Red Major alarm

Blinking red Critical alarm

Table 1-6 Alarm Output LED

Color System Status

Green No alarm

Red Relay closed, alarm present

1-10

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

Chapter 1 Product Overview

Cable Side

Console LEDs

The console LEDs show which console port is in use. See Figure 1-6 and Figure 1-9 for the LED

locations.

If you connect a cable to a console port, the switch automatically uses that port for console

communication. If you connect two console cables, the USB console port has priority.

Port LEDs

RJ-45 ports and SFP-module slots have port LEDs. Port LEDs, as a group or individually, provide

information about the switch and about the individual ports.

Table 1-7 RJ-45 and USB Console Port LEDs

LED Color Description

RJ-45 console port Green RJ-45 console port is active.

USB console port LED is off.

Off Port is not active.

USB console port is active.

USB console port Green USB console port is active.

RJ-45 console port LED is off.

Off Port is not active.

RJ-45 console port is active.

Table 1-8 Meaning of Port LED Colors

LED Color Meaning

Off No link or port was administratively shut down.

Green Link present but not sending or receiving data.

Blinking green Activity. Port is sending or receiving data.

Alternating

green-amber

Link fault. Error frames can affect connectivity, and errors such as excessive

collisions, CRC errors, and alignment and jabber errors are monitored for link

faults.

Amber Port is blocked by Spanning Tree Protocol (STP) and is not forwarding data.

After a port is reconfigured, the port LED is amber for up to 30 seconds as STP

searches for loops.

1-11

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

Chapter 1 Product Overview

Cable Side

PoE LED

Dual-Purpose Port LEDs

The dual-purpose port LEDs identify the connection as either a copper-based connector or an SFP

module. The ports can autonegotiate, or you can manually configure each dual-purpose port as either

10/100/1000 with copper connectors or as an SFP-module port, but not as both types at the same time.

See Table 1-8 for LED descriptions.

SD Flash Memory Card LED

SD Flash Memory Card

The switch ships with the Secure Digital (SD) flash memory card installed. See Figure 1-1 and

Figure 1-2. The switch stores the Cisco IOS software images and the switch configuration on the card.

You should not remove the card unless you want to use it in a replacement switch. You then do not have

to reconfigure the new switch. See the

“Replacing the SD Flash Memory Card” section on page 2-23 for

information.

Table 1-9 PoE LED

Color Meaning

Off PoE is not enabled.

Green PoE is enabled. Ports are functioning correctly.

Amber PoE is enabled, but an error is present.

Table 1-10 SD Flash Memory Card LED

Color System Status

Off / blinking green SD flash memory card transfer in progress.

Blinking amber SD flash memory card is not present (slow blinking).

Unsupported SD flash memory card is detected (fast blinking).

Amber Error accessing the SD flash memory card.

Cisco IOS boot image cannot be found.

Green SD flash memory card is functioning.

1-12

Cisco IE 3010 Switch Hardware Installation Guide

78-19581-02

Chapter 1 Product Overview

Power-Supply Side

The power-supply side has the LED panel and two power-supply slots for the removable power supplies.

See

Figure 1-7 and Figure 1-8.

Figure 1-7 Switch with One Power-Supply Module

Figure 1-8 Switch with Both Power-Supply Modules

For a description of the PSU OK LED, see Table 1-4 on page 1-9.

1 LED panel 3 Power-supply slot 2

2 Power-supply slot 1

2

1

3

208365

Cisco

Sw itch Series

IE 3010

PW R-RGD-LOW -D C

1 PSU OK LED

208375

Cisco IE 3010

Sw itch Series

1

PW R-RGD-LOW -D C

PW R-RGD-LOW-DC

Page is loading ...

Cisco Systems 3010 User manual

This manual is also suitable for

Cisco Systems 3010 User manual

Related papers

Other documents