H3C LS-5820V2-52QF Installation guide

Brand: H3C

Model: LS-5820V2-52QF

Category: Network switches

Type: Installation guide

This manual is also suitable for

H3C S5830V2&S5820V2 Switch Series

Installation Guide

New H3C Technologies Co., Ltd.

http://www.h3c.com.hk

Document version: 6W108-20170606

No part of this manual may be reproduced or transmitted in any form or by any means without prior written

consent of New H3C Technologies Co., Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H

Care, , IRF, NetPilot, Netflow, SecEngine,

SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New H3C Technologies

Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Environmental protection

This product has been designed to comply with the environmental protection requirements. The storage, use,

and disposal of this product must meet the applicable national laws and regulations.

Preface

H3C S5830V2&S5820V2 Switch Series Installation Guide describes the procedures for installing,

accessing, and troubleshooting the H3C S5830V2&S5820V2 Switch Series.

This preface includes the following topics about the documentation:

• Audience.

• Conventions

• Obtaining documentation

• Technical support

• Documentation feedback

Audience

This documentation is intended for:

• Network planners.

• Field technical support and servicing engineers.

• Network administrators working with the S5830V2&S5820V2 switch series.

Conventions

The following information describes the conventions used in the documentation.

Command conventions

Convention Description

Boldface Bold

text represents commands and keywords that you enter literally as shown.

Italic

Italic text represents arguments that you replace with actual values.

[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by vertical bars, from which

you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices separated by vertical bars,

from which you select one or none.

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices separated by vertical

bars, from which you select a minimum of one.

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax choices separated by vertical

bars, from which you select one choice, multiple choices, or none.

&<1-n>

The argument or keyword and argument combination before the ampersand (&) sign

can be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention Description

Boldface

Window names, button names, field names, and menu items are in Boldface. For

example, the

New User

window opens; click

Convention Description

Multi-level menus are separated by angle brackets. For example,

File

Create

Folder

Symbols

Convention Description

WARNING!

An alert that calls attention to important information that if not understood or followed

can result in personal injury.

CAUTION:

An alert that calls attention to important information that if not understood or followed

can result in data loss, data corruption, or damage to hardware or software.

IMPORTANT:

An alert that calls attention to essential information.

NOTE:

An alert that contains additional or supplementary information.

TIP:

An alert that provides helpful information.

Network topology icons

Convention Description

Represents a generic network device, such as a router, switch, or firewall.

Represents a routing-capable device, such as a router or Layer 3 switch.

Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that

supports Layer 2 forwarding and other Layer 2 features.

Represents an access controller, a unified wired-WLAN module, or the access

controller engine on a unified wired-WLAN switch.

Represents an access point.

Wireless terminator unit.

Wireless terminator.

Represents a mesh access point.

Represents omnidirectional signals.

Represents directional signals.

Represents a security product, such as a firewall, UTM, multiservice security

gateway, or load balancing device.

Represents a security module, such as a firewall, load balancing, NetStream, SSL

VPN, IPS, or ACG module.



Examples provided in this document

Examples in this document might use devices that differ from your device in hardware model,

configuration, or software version. It is normal that the port numbers, sample output, screenshots,

and other information in the examples differ from what you have on your device.

Obtaining documentation

To access the most up-to-date H3C product documentation, go to the H3C website at

http://www.h3c.com.hk

To obtain information about installation, configuration, and maintenance, click

http://www.h3c.com.hk/Technical_Documents

To obtain software version information such as release notes, click

http://www.h3c.com.hk/Software_Download

Technical support

service@h3c.com

http://www.h3c.com.hk

Documentation feedback

You can e-mail your comments about product documentation to [email protected].

We appreciate your comments.

Contents

Preparing for installation ···································································· 1

Safety recommendations ············································································································· 1

Examining the installation site ······································································································· 1

Temperature/humidity ·········································································································· 1

Cleanliness ························································································································ 2

EMI ·································································································································· 2

Laser safety ······················································································································· 2

Installation tools ························································································································· 3

Installing the switch ·········································································· 4

Installing the switch in a 19-inch rack ····························································································· 5

Requirements for the rack ····································································································· 5

Mounting brackets and rack-mounting rail kit ············································································· 5

Rack-mounting procedures at a glance ···················································································· 6

Attaching the mounting brackets, chassis rails, and grounding cable to the chassis ··························· 6

Attaching the slide rails to the rack ·························································································· 9

Mounting the switch in the rack ···························································································· 10

Grounding the switch ················································································································ 11

Grounding the switch with a grounding strip ············································································ 12

Grounding the switch by using the AC power cord ···································································· 13

Installing/removing a fan tray ······································································································ 14

Installing a fan tray ············································································································ 14

Removing a fan tray ··········································································································· 15

Installing/removing a power module ····························································································· 15

Installing a power module ···································································································· 16

Removing a power module ·································································································· 17

Connecting the power cord ········································································································ 18

Connecting the LSVM1AC650 or LSVM1AC300 power module ··················································· 19

Connecting the LSVM1DC650 or LSVM1DC300 power module ·················································· 19

Verifying the installation ············································································································· 20

Accessing the switch for the first time ················································· 21

Setting up the configuration environment ······················································································ 21

Connecting the console cable ····································································································· 21

Console cable ··················································································································· 21

Connection procedure ········································································································ 22

Setting terminal parameters ······································································································· 22

Starting the switch ···················································································································· 22

Setting up an IRF fabric ··································································· 24

IRF fabric setup flowchart ·········································································································· 24

Planning IRF fabric setup ··········································································································· 25

Planning IRF fabric size and the installation site ······································································· 25

Identifying the master switch and planning IRF member IDs ······················································· 25

Planning IRF topology and connections·················································································· 26

Identifying physical IRF ports on the member switches ······························································ 27

Planning the cabling scheme ······························································································· 27

Configuring basic IRF settings ···································································································· 29

Connecting the physical IRF ports ······························································································· 29

Accessing the IRF fabric to verify the configuration ········································································· 29

Maintenance and troubleshooting ······················································ 31

Power module failure ················································································································ 31

Symptom ························································································································· 31

Solution ··························································································································· 31

Fan tray failure ························································································································ 31

Configuration terminal problems ·································································································· 31

No terminal display ············································································································ 32

Garbled terminal display ····································································································· 32

Appendix A Chassis views and technical specifications ·························· 33

Chassis views ························································································································· 33

S5830V2-24S ··················································································································· 33

S5820V2-48S ··················································································································· 34

S5820V2-52QF ················································································································· 35

S5820V2-52QF-U ·············································································································· 38

S5820V2-52Q ··················································································································· 39

S5820V2-54QS-GE ··········································································································· 40

Technical specifications ············································································································· 41

Appendix B FRUs and compatibility matrixes ······································· 43

Power modules ······················································································································· 43

Fan trays ································································································································ 44

Appendix C Ports and LEDs ····························································· 46

Ports ····································································································································· 46

Console port ····················································································································· 46

Management Ethernet port ·································································································· 46

USB port ························································································································· 46

SFP+ port ························································································································ 47

QSFP+ port ······················································································································ 49

10/100/1000Base-T autosensing Ethernet port ········································································ 51

1/10GBase-T autosensing Ethernet port ················································································· 51

LEDs ····································································································································· 52

System status LED ············································································································ 52

SFP+ port LED ················································································································· 52

QSFP+ port LED ··············································································································· 52

10/100/1000Base-T autosensing Ethernet port LEDs ································································ 53

1/10GBase-T autosensing Ethernet port LEDs ········································································· 53

Management Ethernet port LEDs ·························································································· 53

Appendix D Cooling system ······························································ 54

Index ··························································································· 56

Preparing for installation

Safety recommendations

To avoid any equipment damage or bodily injury, read the following safety recommendations before

installation. Note that the recommendations do not cover every possible hazardous condition.

• Before cleaning the switch, remove all power cords from the switch. Do not clean the switch

with wet cloth or liquid.

• Do not place the switch near water or in a damp environment. Prevent water or moisture from

entering the switch chassis.

• Do not place the switch on an unstable case or desk. The switch might be severely damaged in

case of a fall.

• Ensure good ventilation of the equipment room and keep the air inlet and outlet vents of the

switch free of obstruction.

• Make sure the operating voltage is in the required range.

• To avoid electrical shocks, do not open the chassis while the switch is operating or when the

switch is just powered off.

• When replacing FRUs, including power modules and fan trays, wear an ESD wrist strap to

avoid damaging the units.

Examining the installation site

The switch must be used indoors.

Mount your switch in a rack and make sure:

• Adequate clearance is reserved at the air inlet and outlet vents for ventilation.

• The rack has a good ventilation system.

• Identify the hot aisle and cold aisle at the installation site, and make sure ambient air flows into

the switch from the cold aisle and exhausts to the hot aisle.

• Identify the airflow designs of neighboring devices, and prevent hot air flowing out of the bottom

device from entering the top device.

• The rack is sturdy enough to support the switch and its accessories.

• The rack is reliably grounded.

To ensure correct operation and long service life of your switch, install it in an environment that meets

the requirements described in the following subsections.

Temperature/humidity

Maintain appropriate temperature and humidity in the equipment room.

• Lasting high relative humidity can cause poor insulation, electricity leakage, mechanical

property change of materials, and metal corrosion.

• Lasting low relative humidity can cause washer contraction and ESD and bring problems

including loose mounting screws and circuit failure.

• High temperature can accelerate the aging of insulation materials and significantly lower the

reliability and lifespan of the switch.

For the temperature and humidity requirements of different switch models, see "Appendix A Chassis

views and technical specifications."

Cleanliness

Dust buildup on the chassis might result in electrostatic adsorption, which causes poor contact of

metal components and contact points, especially when indoor relative humidity is low. In the worst

case, electrostatic adsorption can cause communication failure.

Table 1 Dust concentration limit in the equipment room

Substance Concentration limit (particles/m

)

Dust

≤ 3 x 10

(no visible dust on the tabletop over three days)

NOTE:

Dust diameter ≥ 5 μm

The equipment room must also meet limits on salts, acids, and sulfides to eliminate corrosion and

premature aging of components, as shown in Table 2.

Table 2

Harmful gas limits in the equipment room

Gas Maximum concentration (mg/m

)

0.2

S 0.006

0.05

0.01

EMI

All electromagnetic interference (EMI) sources, from outside or inside of the switch and application

system, adversely affect the switch in the following ways:

• A conduction pattern of capacitance coupling.

• Inductance coupling.

• Electromagnetic wave radiation.

• Common impedance (including the grounding system) coupling.

To prevent EMI, use the following guidelines:

• If AC power is used, use a single-phase three-wire power receptacle with protection earth (PE)

to filter interference from the power grid.

• Keep the switch far away from radio transmitting stations, radar stations, and high-frequency

devices.

• Use electromagnetic shielding, for example, shielded interface cables, when necessary.

Laser safety

WARNING!

Do not stare into any fiber port when the switch has power. The laser light emitted from the optical

fiber might hurt your eyes.

The switch is a Class 1 laser device.

Installation tools

The installation tools are not provided with the switch. Prepare them yourself.

• Phillips screwdriver.

• ESD wrist strap.

• Marker.

Installing the switch

CAUTION:

Keep the tamper-proof seal on a mounting screw on the chassis cover intact, and if you want to open

the chassis, contact H3C for permission. Otherwise, H3C shall not be liable for any consequence

caused thereby.

Figure 1 Hardware installation flow

Installing the switch in a 19-inch rack

Requirements for the rack

To close the rack door easily, make sure the rack depth for the S5830V2-24S, S5820V2-52QF

(LS-5820V2-52QF), S5820V2-52QF-U, and S5820V2-52Q switches is a minimum of 1000 mm

(39.37 in).

The distance from the front to the rear posts of the rack must meet the requirements described

in Table 3.

Table 3

Requirements for the distance from the front to rear rack posts

Switch model Installation method Minimum distance

Maximum

distance

S5830V2-24S

Using mounting brackets and

slide rails (provided)

401 mm (15.79 in) 875 mm (34.45 in)

• S5820V2-48S

• S5820V2-52QF

(LS-5820V2-52QF-H3)

• S5820V2-52QF

(LS-5820V2-52QF-H5)

• S5820V2-54QS-GE

Using mounting brackets and

slide rails (provided)

401 mm (15.79 in) 634 mm (24.96 in)

Using mounting brackets and

long slide rails (optional)

621 mm (24.45 in) 854 mm (33.62 in)

• S5820V2-52QF

(LS-5820V2-52QF)

• S5820V2-52QF-U

• S5820V2-52Q

Using mounting brackets and

slide rails (provided)

405 mm (15.94 in) 834 mm (32.83 in)

Mounting brackets and rack-mounting rail kit

The S5830V2&S5820V2 switches come with a pair of mounting brackets (see Figure 2) and a

rack-mounting kit that includes a pair of chassis rails and a pair of slide rails (see Figure 3).

Figure 2 1U mounting bracket kit

Figure 3 Rack-mounting rail kit

(1) Chassis rail (2) Slide rail

Rack-mounting procedures at a glance

Figure 4 Rack-mounting procedure

NOTE:

• If a rack shelf is available, you can put the switch on the rack shelf, slide the switch to an

appropriate location, and attach the switch to the rack with the mounting brackets.

• To rack-mount the switch, you must use both the mounting bracket and the rack-mounting rail kit.

Attaching the mounting brackets, chassis rails, and

grounding cable to the chassis

The switch has one front mounting position (near the network ports) and one rear mounting position

(near the power modules).

The S5830V2-24S has one primary grounding point (with a grounding sign) and one auxiliary

grounding point. The S5820V2-48S, S5820V2-52QF, S5820V2-52QF-U, S5820V2-52Q, and

S5820V2-54QS-GE switches each have one primary grounding point (with a grounding sign) and

two auxiliary grounding points. Use the primary grounding point whenever possible. If the primary

grounding point fails or is not suitable for the installation site, use one of the auxiliary grounding

points.

1 2

Figure 5 Mounting and grounding positions of the S5830V2-24S

(1) Rear mounting position (2) Primary grounding point

(3) Auxiliary grounding point 1 (4) Front mounting position

Figure 6 Mounting and grounding positions of the S5820V2-52QF

(LS-5820V2-52QF)/S5820V2-52QF-U/S5820V2-52Q

(1) Auxiliary grounding point 2 (2) Rear mounting position

(3) Primary grounding point (4) Auxiliary grounding point 1

(5) Front mounting position

1 2 3 4 5

Figure 7 Mounting and grounding positions of the S5820V2-48S/S5820V2-52QF

(LS-5820V2-52QF-H3) /S5820V2-52QF (LS-5820V2-52QF-H5)/S5820V2-54QS-GE

(1) Auxiliary grounding point 2 (2) Rear mounting position

(3) Primary grounding point (4) Auxiliary grounding point 1

(5) Front mounting position

Attaching the mounting brackets and chassis rails to the chassis

1. Align the mounting brackets with the screw holes in the rear mounting position (see Figure 8) or

front mounting position (see Figure 9).

2. Use M4 screws (provided) to attach the mounting brackets to the chassis.

3. Align the chassis rails with the rail mounting holes in the chassis:

{ If the mounting brackets are in the rear mounting position, align the chassis rails with the

screw holes at the front of the side panels (see Figure 8).

{ If the mounting brackets are in the front mounting position, align the chassis rails with the

screw holes at the rear of the side panels (see Figure 9).

4. Use M4 screws (provided) to attach the chassis rails to the chassis.

NOTE:

Secure the mounting brackets and chassis rails to both sides of the chassis in the same way.

Connecting the grounding cable to the chassis

CAUTION:

Select the grounding point as required. The primary grounding point and auxiliary grounding point 1

are located on the left side panel. If you use one of these grounding points, you must connect the

grounding cable to the grounding point before you mount the switch in the rack.

To connect the grounding cable to a chassis grounding point, for example, the primary grounding

point:

1. Choose a grounding point.

2. Unpack the grounding cable and grounding screws.

3. Align the two-hole grounding lug at one end of the cable with the grounding holes of the

grounding point, insert the grounding screws into the holes, and tighten the screws with a

screwdriver to attach the grounding lug to the chassis, as shown in Figure 8.

4 5

Figure 8 Attaching the rear mounting brackets/chassis rails/grounding cable to the chassis

Figure 9 Attaching the front mounting brackets/chassis rails to the chassis

NOTE:

• As a best practice, use the primary grounding point or auxiliary grounding point 1 because the

grounding cable and grounding screw that come with the switch are suitable only for these two

grounding points.

• To use auxiliary grounding point 2 on the S5820V2-48S, S5820V2-52QF, S5820V2-52QF-U,

S5820V2-52Q, or S5820V2-54QS-GE switch, prepare a grounding cable yourself.

Attaching the slide rails to the rack

1. Identify the rack attachment position for the slide rails.

2. Install cage nuts (user-supplied) in the mounting holes in the rack posts.

3. Align the screw holes in one slide rail with the cage nuts in the rack post on one side, and use

screws (user supplied) to attach the slide rail to the rack, as shown in Figure 10.

4. Rep

eat the preceding step to attach the other slide rail to the rack post on the other side.

Keep the two slide rails at the same height so the slide rails can attach into the chassis rails.

Figure 10 Installing the slide rails

Mounting the switch in the rack

This task requires two people.

To mount the switch in the rack:

1. Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded.

2. Verify that the mounting brackets and chassis rails have been securely attached to the switch

chassis.

3. Verify that the slide rails have been correctly attached to the rear rack posts.

4. Attach cage nuts (user-supplied) to the front rack posts and make sure they are at the same

level as the slide rails.

5. One person supports the bottom of the switch, aligns the chassis rails with the slide rails on the

rack posts, and then slides the chassis rails slowly along the slide rails until the mounting

brackets are flush with the rack posts.

6. Another person uses screws (user-supplied) to attach the mounting brackets to the rack.

To secure the switch in the rack, make sure the front ends of the slide rails reach out of the

chassis rails.

Figure 11 Mounting the switch in the rack (1)

Figure 12 Mounting the switch in the rack (2)

Grounding the switch

WARNING!

Correctly connecting the switch grounding cable is crucial to lightning protection and EMI protection.

The power input end of the switch has a noise filter, whose central ground is directly connected to the

chassis to form the chassis ground (commonly known as PGND). You must securely connect this

chassis ground to the earth so the faradism and leakage electricity can be safely released to the

earth to minimize EMI susceptibility of the switch.

You can ground a switch by using a grounding strip at the installation site or the AC power cord

connected to the switch.

NOTE:

The power and grounding terminals in this section are for illustration only.

Grounding the switch with a grounding strip

WARNING!

Connect the grounding cable to the grounding system in the equipment room. Do not connect it to a

fire main or lightning rod.

If a grounding strip is available at the installation site, connect the grounding cable to the grounding

strip.

To connect the grounding cable:

1. Attach the two-hole grounding lug at one end of the grounding cable to a grounding point on the

switch chassis (see "Connecting the grounding cable to the chassis").

2. Remove the

hex nut of a grounding post on the grounding strip.

3. Attach the ring terminal at the other end of the grounding cable to the grounding strip through

the grounding post, and fasten the ring terminal with the removed hex nut.

Figure 13 Connecting the grounding cable to a grounding strip

(1) Hex nut (2) Ring terminal

(3) Grounding post (4) Grounding strip

NOTE:

• As a best practice, use the primary grounding point or auxiliary grounding point 1, because the

grounding cable and grounding screw provided with the switch are applicable only to these two

grounding points.

• To use auxiliary grounding point 2 on the S5820V2-48S/S5820V2-52QF, S5820V2-52QF-U,

S5820V2-52Q, or S5820V2-54QS-GE switch, prepare a grounding cable yourself. The

connection method is the same as connecting to the other two grounding points.

Grounding the switch by using the AC power cord

If the installation site does not have any grounding strips, you can ground an AC-powered switch

through the protective earth (PE) wire of the power cord, but must make sure:

• The power cord has a PE terminal.

• The ground contact in the power outlet is securely connected to the ground in the power

distribution room or on the AC transformer side.

• The power cord is securely connected to the power outlet.

NOTE:

If the ground contact in the power outlet is not connected to the ground, report the problem and

reconstruct the grounding system.

Figure 14 Grounding through the PE wire of the AC power cord

(1) Three-wire AC power cable (2) Chassis rear panel

NOTE:

To guarantee the grounding effect, use the grounding cable provided with the switch to connect to

the grounding strip in the equipment room as long as possible.

Page is loading ...

H3C LS-5820V2-52QF Installation guide

Brand: H3C

Model: LS-5820V2-52QF

Category: Network switches

Type: Installation guide

This manual is also suitable for

Download PDF

report

H3C LS-5820V2-52QF Installation guide

This manual is also suitable for

H3C LS-5820V2-52QF Installation guide

Related papers

Other documents