AD1200EXP MCS
Hard-wire Controller Expander
Installation Instructions
The manual describes the installation procedures for the American Dynamics AD1200EXP MCS Hard-wire Controller Expander.
Before installation, become familiar with all of the special features and warnings associated with this equipment. Store this
manual in a safe, convenient location for future reference.
This software/firmware is confidential to and is copyrighted by SENSORMATIC ELECTRONICS CORPORATION. It is not to
be copied or disclosed in any manner without the express written consent of SENSORMATIC. The software is furnished to the
purchaser under a license for use on a single system.
NOTE: Information furnished by SENSORMATIC is believed to be accurate and reliable. However, no responsibility is
assumed by SENSORMATIC for its use; nor for any infringements of other rights of third parties which may result from its use.
No license is granted by implications or otherwise under any patent or patent rights of SENSORMATIC.
Copyright 1997 by SENSORMATIC. All rights reserved.
The installation of this product should be made by qualified
service personnel and should conform to all local codes.
QA301D
!
WW
WW
AA
AA
RR
RR
NN
NN
II
II
NN
NN
GG
GG
To reduce the risk of fire or shock hazard, do
not expose this product to rain or moisture.
AMERICAN
DYNAMICS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVERS (OR BACK) .
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
RISK OF ELECTRIC SHOCK
DO NOT OPEN
 CAUTION
!
The lightning flash with arrowhead
symbol, within an equilateral
triangle, is intended to alert the
user to the presence of uninsulated
"dangerous voltage" within the
product's enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance
(servicing) instructions in the
literature accompanying the product.
UU
UU
NN
NN
PP
PP
AA
AA
CC
CC
KK
KK
II
II
NN
NN
GG
GG
AA
AA
NN
NN
DD
DD
II
II
NN
NN
SS
SS
PP
PP
EE
EE
CC
CC
TT
TT
II
II
OO
OO
NN
NN
Unpack carefully. This is an electronic product and should
be handled as such. Compare the items received with the
packing list with your order.
Be sure to save:
1. The shipping cartons and insert pieces. They are the )
safest material in which to make future shipments of
the product.
2. The IMPORTANT SAFEGUARDS sheet.
3. These Installation and Operating Instructions.
MM
MM
AA
AA
II
II
NN
NN
TT
TT
EE
EE
NN
NN
AA
AA
NN
NN
CC
CC
EE
EE
User maintenance of this unit is limited to external cleaning
and inspection. For specific recommendations refer to the
IMPORTANT SAFEGUARDS sheet packaged with this product.
II
II
NN
NN
SS
SS
TT
TT
AA
AA
LL
LL
LL
LL
AA
AA
TT
TT
II
II
OO
OO
NN
NN
AA
AA
NN
NN
DD
DD
SS
SS
EE
EE
RR
RR
VV
VV
II
II
CC
CC
EE
EE
If you require information during installation of this
product or if service seems necessary, contact the
Sensormatic Repair and Service Department at (800)
442-2225. You must obtain a Return Authorization Number
and shipping instructions before returning any product for
service.
Do not attempt to service this product yourself. Opening or
removing covers may expose you to dangerous voltages or
other hazards. Refer all servicing to qualified personnel.
This equipment has been tested and
found to comply with Part 15 of the
FCC Rules.
Operation is subject to the
following two conditions: 1. This
device may not cause harmful
interference, and 2. This device
must accept any interference
received, including interference
that may cause undesired operation.
Table of Contents
DESCRIPTION............................................................................................................................ 1
FEATURES ................................................................................................................................. 1
MAINTENANCE........................................................................................................................ 1
INSTALLATION ........................................................................................................................ 2
Front Panel Description................................................................................................. 2
Rear Panel Description.................................................................................................. 2
Mounting ....................................................................................................................... 4
Power............................................................................................................................. 4
Powering Up.................................................................................................................. 4
AD1200EXP to AD1200A Hard-wired Controller....................................................... 4
Cascading Multiple AD1200EXP Units........................................................................ 6
Powering Multiple AD1200EXP Units......................................................................... 8
Connecting Multiple AD1200EXP Units...................................................................... 10
AD1200EXP -to- Pan/Tilt Site Connection .................................................................. 12
Cable Selection.............................................................................................................. 12
CCTV Switcher System Connection............................................................................. 14
AD1200EXP to AD1412 Series Switcher Connection ................................................. 14
AD1200EXP to AD1416 Series Switcher Connection ................................................. 15
SETUP ....................................................................................................................................... 16
4-Position DIP Switch................................................................................................... 16
OPERATION............................................................................................................................... 17
Single AD1200EXP Unit Operation ............................................................................. 17
Multiple AD1200EXP Unit Operation.......................................................................... 17
CCTV Switcher Switcher System Operation ................................................................ 17
Technical Support.......................................................................................................... 17
APPENDIX
INDEX ....................................................................................................................................... A-1
DIMENSIONS............................................................................................................................. A-2
SPECIFICATIONS...................................................................................................................... Back Cover
1
AD1200EXP DESCRIPTION
DESCRIPTION
The AD1200EXP Hardwired Controller Expander increases
the number of pan/tilt sites controlled from a single AD1200A
Hard-wired Controller from one to four. Cascading multiple
AD1200EXP units increases the number of pan/tilt sites
available from four to a maximum of sixteen.
The AD1200EXP features spring loaded pushbuttons for fast
pan/tilt site selection. Each pushbutton features internal LED
illumination to confirm the selected site.
Snap-on connectors enable simple interconnections between
multiple AD1200EXP units, between pan/tilt sites, and
between CCTV switching systems. A 30-inch wire harness is
provided with the AD1200EXP for direct connection to the
AD1200A Controller.
FEATURES
• Operate four Pan/Tilts from One Control Site (Expandable
to 16 Pan/Tilts)
• Front Panel Push-buttons with Internal LED Illumination
• Fast Installation with Snap-on Connectors
• Connects to MCS Compatible Sequential Switching
Systems for Controller Follower Operation
• Desktop Operation
• Rack Mount Kit Available
MAINTENANCE
The AD1200EXP Series Controller Expander contains no user
serviceable parts. American Dynamics recommends
performing the following checks on a routine basis:
• One month after installation and every six month thereafter,
check the tightness and security of all external fastenings.
• Every six months, check all electrical cables for signs of
wear.
This installation should be made by qualified service personnel
and conform to all local codes. Take precautions to avoid
unintentional operation by employees, customers, and
maintenance personnel working about the premises.
PTZ Controller Expander
M
M
C
C
S
S
1
2
3
4
Figure 1 - AD1200EXP Controller Expander Illustration
2
INSTALLATION
Front Panel Description
Site Selection Pushbuttons:
Four spring-loaded pushbuttons select the individual
pan/tilt unit the operator wishes to control
(see Figure 2).
Internal LED illumination indicates current site
selected.
Rear Panel Description
Options DIP Switch
A 4-position DIP switch identifies individual
AD1200EXP units when cascading multiple EXP
units together (see Figure 3).
Ground Connection
A ground bolt provides a common ground connection
between the AD1200EXP and the individual pan/tilt
sites and related equipment.
Pan/Tilt Unit Connectors
Four 14-pin connectors provide control outputs for
pan/tilt and automatic lens functions.
Control Harness
The control harness receives pan/tilt and automatic
lens function signals from the AD1200A Hard-wired
Controller and routes them to the appropriate
pan/tilt site.
5-Pin Connectors
Two 5-pin connectors provide the AD1200EXP with
cascading capabilities and/or integration to sequential
video switching systems.
INSTALLATION AD1200EXP
Site Selection Pushbuttons
(Pan/Tilt Sites 1, 2, 3, and 4)
1234
PTZ Controller Expander
MCS
Figure 2 - AD1200EXP Panel Layout
3
AD1200EXP INSTALLATION
Figure 3 - AD1200EXP Rear Panel Layout
14-Pin Connecters (4)
1 2 3 4
U D R L 1 2 R C I F Z
N
C
N
C
N
C
U D R L 1 2 R C I F Z
N
C
N
C
N
C
1
2
3
Ground
Connection
4
14-Pin Ramp Connector
Options DIP
Switch
0 1 2 3 G
5-Pin Connecters (2)
OFF
4
Mounting
The AD1200EXP is suitable for desktop operation or mounting
in a standard EIA rack. The American Dynamic's AD2117/21
Rack Mount Hardware Kit is recommended for mounting one
or two AD1200EXPs in a standard EIA rack.
Power
The AD1200EXP is configured for use with 24VAC power.
A single AD1200EXP unit receives its power directly from the
AD1200A Hard-wired Controller.
In cases of multiple AD1200EXP units, power is derived in
two ways. One AD1200EXP unit receives power directly from
the AD1200A Hard-wired Controller and the remaining units
receive power from one external step-down transformer (not
supplied).
Powering Up
• Complete all connections between the AD1200EXP and the
AD1200A Hard-wired Controller.
• Complete all installation and connection procedures
between the pan/tilt and the AD1200EXP.
• Verify monitor connection for viewing camera output.
AD1200EXP -to- AD1200A Hard-wired Controller
Connection
The AD1200EXP is provided with a 15-lead harness that joins
to a 14-pin connector supplied with the AD1200A Hard-wired
Controller.
NOTE: The extra lead (#15) connects to the AD1200A
Controller ground lug (see Table 1 and Figure 4).
Figure 4 shows the wiring between the AD1200EXP and the
AD1200A Hard-wired Controller.
1. Attach the 14-pin connector to the mating connector on
the rear panel of the AD1200A Hard-wired Controller.
NOTE: Table 1 provides a reference indicating the particular
wire colors with their respective pin designations and
functions.
INSTALLATION AD1200EXP
!
CAUTION
Do not connect the primary power source until
completing the following checklist.
Wire Harness
Wire Color
Black
White
Red
Green
Orange
Blue
Wht/Blk
Red/Blk
Grn/Blk
Orn/Blk
Blu/Blk
Blk/Wht
Red/Wht
Grn/Wht
Blu/Wht
AD1200A Controller
Function
Tilt UP
Tilt DOWN
Pan RIGHT
Pan LEFT
Aux 1
Aux 2
24VAC Power
24VAC COMMON
Lens COMMON
Lens IRIS
Lens FOCUS
Lens ZOOM
24VAC Camera Power
24VAC COMMON
Chassis Ground
AD1200EXP Expander
Function
Tilt UP
Tilt DOWN
Pan RIGHT
Pan LEFT
Aux 1
Aux 2
No Connection
24VAC COMMON
Lens COMMON
Lens IRIS
Lens Focus
Lens ZOOM
24VAC Power
24VAC COMMON
Chassis Ground
14-Pin Connector Position
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
No Connection
Table 1 - AD1200EXP -to- AD1200A Hard-wired Controller Connection
AD1200EXP INSTALLATION
5
AD1200EXP
1 2 3 4
U D R L 1 2 R C I F Z
N
C
N
C
N
C
U D R L 1 2 R C I F Z
N
C
N
C
N
C
0 1 2 3 G
1
2
3
4
AUTO
SCAN
120V
60Hz
LENS
ADJUST
AUX
P/T
A/P
LENS
U D R L 1 2 H R C I F Z
CP
1 2 3 4
OFF
AD1200A Controller
CHASSIS GROUND
AUX
P/T
A/P
LENS
U D R L 1 2 H R C I F Z
CP
14-Pin Connector
ZOOM
FOCUS
IRIS
COMMON
P/T & AUX RETURN
UP
DOWN
RIGHT
LEFT
AUX 1
AUX 2
24VAC
24VAC
OFF
14-Pin Mating Connector
Figure 4 - Single AD1200EXP Expander -to- AD1200A Hard-wired Controller Connection
Cascading Multiple AD1200EXP Units
Multiple AD1200EXP units are used to increase the number of
pan/tilt sites available to a single AD1200A Hard-wired
Controller from four to a maximum of sixteen. Each
AD1200EXP unit is provided with one 5-pin strap harness for
cascading purposes.
1. Beginning with the LAST AD1200EXP unit, connect a
suitable ground lead between the ground terminals located
on the rear panel of each AD1200EXP unit (see Figure 5).
NOTE: Proper grounding requires a minimum 18AWG solid
wire.
2. Connect the ground lead between the FIRST AD1200EXP
unit and the ground terminal on the rear panel of the
AD1200A Hard-wired Controller (see Figure 6).
3. Beginning with the last AD1200EXP unit, connect a 5-
pin strap harness from the CASCADE IN connector to the
CASCADE OUT connector on the next-to-last
AD1200EXP unit.
3. Working from last to first, continue connecting the 5-pin
strap harnesses from the CASCADE IN connector to the
CASCADE OUT connector for the remaining
AD1200EXP units.
INSTALLATION AD1200EXP
6
0 1 2 3 G
Cascade IN and
Switcher System OUT
5-Pin Connecter
Cascade OUT
5-Pin Connecter
1 2 3
4
U D R L 1 2 R C I
F Z
N
C
N
C
N
C
U D R L 1 2 R C I
F Z
N
C
N
C
N
C
1
2
3
4
0 1 2 3 G
Ground Terminal
Figure 5 - 5-Pin Connector Location
CAUTION
Disconnect all AD1200EXP and AD1200A
Hard-wired Controller units from their
respective power sources before proceeding with
any connections! Severe damage to the internal
electronics as well as personal injury may result!
!
7
AD1200EXP INSTALLATION
1
2
3
4
0 1 2 3 G
AD1200EXP
1
2
3
4
0 1 2 3 G
0 1 2 3 G
1
2
3
4
Chassis Ground
Connection
(18AWG Solid Wire)
to AD1200A Hard-wire Controller
Chassis Ground Terminal
Strap Harness
1
2
3
4
0 1 2 3 G
Strap Harness
OFF
Strap Harness
5-Pin Connector
w/ Strap Harness Attached
0 1 2 3 G
0 1 2 3 G
0 1 2 3 G
Figure 6 - Cascading AD1200EXP Units
8
Powering Multiple AD1200EXP Units
Connecting multiple (maximum of 4) AD1200EXP units to
one AD1200A Controller requires the use of an external
120VAC to 24VAC step-down transformer.
NOTE: Connecting multiple AD1200EXPs for European
operation requires the use of a 230VAC to 24VAC
step-down transformer.
The first AD1200EXP draws 24VAC power directly from the
AD1200A Controller (see Figure 7).
The remaining three AD1200EXP units require an external
step-down transformer. These three units are wired in parallel
from the single step-down transformer (see Figure 7).
NOTES: A 120VAC step-down transformer may be ordered
directly from American Dynamics (part# AD124)
or purchased separately. Step-down transformer
requirements for North American operation are
120VAC-to-24VAC, with a minimum output of 30
VA, class 2, if powered from other than an
AD1200A.
A 230VAC step-down transformer may be ordered
directly from American Dynamics (part# ADE125)
or purchased separately. Step-down transformer
requirements for European operation are 230VAC-
to-24VAC, with a minimum output of 30 VA.
For the FIRST AD1200EXP Unit in a Series:
1. Connect the 14-pin connector of the FIRST (Unit #1)
AD1200EXP in a series to the 14-pin mating connector on
the rear panel of the AD1200A Controller (see Figure 7).
NOTES: Refer to Table 1, page 4, and Figure 4, page 5, for a
diagram of the AD1200EXP 14-pin connecter.
The first AD1200EXP unit in a series draws power
directly from the AD1200A Controller. All
remaining AD1200EXP units in the series draws
power from a separate transformer.
The 24VAC POWER lead from the FIRST
AD1200EXP in the series connects through the 14-
pin connector to the AD1200A Hard-wired
Controller.
The 24VAC COMMON lead from the FIRST
AD1200EXP in the series connects through the 14-
pin connector to the AD1200A Hard-wired
Controller.
For the SECOND, THIRD, and FOURTH AD1200EXP
Units in a Series:
2. Disconnect the 24VAC POWER lead (Wht/Blk) from pin
7 of EACH of the AD1200EXP 14-pin connectors.
3. Connect the 24VAC POWER lead of each of the
AD1200EXP units in the series to one of the output
screws of the step-down transformer (see Figure 7).
4. Disconnect the 24VAC COMMON lead (Red/Blk) from
pin 8 of EACH of the AD1200EXP 14-pin connectors.
5. Connect the 24VAC COMMON lead of each of the
AD1200EXP units in the series to the other output screw
of the step-down transformer (see Figure 7).
INSTALLATION AD1200EXP
24VAC POWER
24VAC COMMON
AD1200A Controller
AD1200A Controller
AD124 Transformer
AD124 Transformer
AD124 Transformer
AD124 Transformer
AD124 Transformer
AD124 Transformer
Table 2 - Multiple AD1200EXP Unit Power Sources
AD1200EXP Unit #1 AD1200EXP Unit #2 AD1200EXP Unit #3
AD1200EXP Unit #4
CAUTION
Disconnect all AD1200EXP and AD1200A
Controller units from their respective power
sources before proceeding with any connections!
Severe damage to the internal electronics as well
as personal injury may result!
!
120VAC POWER SOURCE
24VAC POWER
24VAC COMMON
ADE1200A Controller
ADE1200A Controller
ADE125 Transformer
AD125 Transformer
ADE125 Transformer
ADE125 Transformer
ADE125 Transformer
ADE125 Transformer
230VAC POWER SOURCE
9
AD1200EXP INSTALLATION
AUTO
SC AN
120V
60Hz
LEN S
ADJUST
AUX
P/T
A/P
LEN S
U D R L 1 2 H R C I F Z
CP
1 2 3
4
OFF
AD1200A Hard-wire Controller
AD1200EXP Unit #1
24VAC COMMON
24VAC POWER
AD1200EXP Unit #2
AD1200EXP Unit #3
AD1200EXP Unit 4
U D R L 1 2 R C
I F Z
N
C
N
C
U D R L 1 2 R C
I F Z
N
C
N
C
0 1 2 3 G
1
2
3
4
OFF
Stepdown Transformer
120VAC-to-24VAC (North America)
230VAC-to-24VAC (Europe)
AC
AC
U D R L 1 2 R C
I F Z
N
C
N
C
U D R L 1 2 R C
I F Z
N
C
N
C
0 1 2 3 G
1
2
3
4
OFF
U D R L 1 2 R C
I F Z
N
C
N
C
U D R L 1 2 R C
I F Z
N
C
N
C
0 1 2 3 G
1
2
3
4
OFF
U D R L 1 2 R C
I F Z
N
C
N
C
U D R L 1 2 R C
I F Z
N
C
N
C
0 1 2 3 G
1
2
3
4
OFF
AD1200EXP -to- AD1200A
Controller Wire Harness
24VAC COMMON
24VAC POWER
Control Connections NOT SHOWN
(see Figure 8, page 11)
24VAC COMMON
24VAC POWER
24VAC COMMON
24VAC POWER
Control Connections NOT SHOWN
(see Figure 8, page 11)
Figure 7 - Power Connections to Multiple AD1200EXP Units
10
Connecting Multiple AD1200EXP Units
A maximum of four AD1200EXP units may be connected to
one AD1200A Hard-wired Controller. All AD1200EXP units
connect to the AD1200A Hard-wired Controller via a single
14-pin connector (provided with the AD1200 Hard-wire
Controller).
Each of the terminals on the 14-pin connector is large enough
to accept four leads (one lead from each of the AD1200EXP
harnesses).
Pin #1 of the AD1200 Hard-wire controller 14-pin connector is
used for the Tilt UP function (see Table 3). Thus, the Tilt UP
lead of ALL the AD1200EXP units connects to pin #1 of the
14-pin connector.
Likewise, pin #2 of the AD1200 Hard-wire controller 14-pin
connector is the Tilt DOWN function (see Table 3). Thus, the
Tilt DOWN lead of ALL the AD1200EXP units connects to
pin #2 of the 14-pin connector.
Figure 8 (page 11) shows a representative schematic of how
multiple AD1200A units connect to the AD1200A Hard-wire
Controller through the 14-pin connector.
NOTE: Table 3 lists the individual wire to connector pin
designations for all AD1200EXP units.
1. Using Table 3 as reference, connect each flying lead from
the four EXP units to the appropriate terminal of the 14-
pin connector (see Figure 8).
NOTE: Refer to page 8, Powering Multiple AD1200EXP
Units, for specific information regarding pin # 13 and
pin #14 power connections.
2. Tighten the clamp screws on the top of the connector as
each group of leads is inserted into the terminals.
3. After tightening the clamp screws, gently pull on each
wire to verify that is securely held in place.
4. Attach the 14-pin connector to the mating connector on
the rear panel of the AD1200 Controller.
INSTALLATION AD1200EXP
Table 3 - Multiple AD1200EXP -to- AD1200A Hard-wired Controller Connection
CAUTION
Disconnect all AD1200EXP and AD1200A
Controller units from their respective power
sources before proceeding with any connections!
Severe damage to the internal electronics as well
as personal injury may result!
!
Wire Harness
Wire Color
Black
White
Red
Green
Orange
Blue
Wht/Blk
Red/Blk
Grn/Blk
Orn/Blk
Blu/Blk
Blk/Wht
Red/Wht
Grn/Wht
Blu/Wht
AD1200A Controller
Function
Tilt UP
Tilt DOWN
Pan RIGHT
Pan LEFT
Aux 1
Aux 2
24VAC Power
24VAC COMMON
Lens COMMON
Lens IRIS
Lens FOCUS
Lens ZOOM
24VAC Camera Power
24VAC COMMON
Chassis Ground
AD1200EXP Port Expander
Function
Tilt UP
Tilt DOWN
Pan RIGHT
Pan LEFT
Aux 1
Aux 2
No Connection
24VAC COMMON
Lens COMMON
Lens IRIS
Lens FOCUS
Lens ZOOM
24VAC Power
24VAC Common
Chassis Ground
14-Pin Connector
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
No Connection
11
Figure 8 - Multiple AD1200EXP Unit -to- AD1200A Hard-wired Controller Connection
AD1200EXP INSTALLATION
U D R L 1 2 R C
I F Z
N
C
N
C
N
C
U D R L 1 2 R C
I F Z
N
C
N
C
N
C
0 1 2 3 G
1
2
3
4
U D R L 1 2 R C
I F Z
N
C
N
C
N
C
U D R L 1 2 R C
I F Z
N
C
N
C
N
C
0 1 2 3 G
1
2
3
4
U D R L 1 2 R C
I F Z
N
C
N
C
N
C
U D R L 1 2 R C
I F Z
N
C
N
C
N
C
0 1 2 3 G
1
2
3
4
AD1200EXP
U D R L 1 2 R C
I F Z
N
C
N
C
N
C
U D R L 1 2 R C
I F Z
N
C
N
C
N
C
0 1 2 3 G
1
2
3
4
ZOOM - Pin 12
FOCUS - Pin 11
UP - Pin 1
DOWN - Pin 2
RIGHT - Pin 3
AUX 2 - Pin 6
P/T & AUX COMMON - Pin 8
Ground
Ground
Ground
Ground
OFF
OFF
OFF
OFF
AUTO
SC AN
120V
60Hz
LEN S
ADJUST
A/P
CP
OFF
AD1200A Hard-wire Controller
LEN S
AUX
Ground
U D R L 1 2 H R C I F
Z
P/T
LEFT - Pin 4
AUX 1 - Pin 5
LENS COMMON - Pin 9
IRIS - Pin 10
Wire Connector
NOTE: Power Connections NOT SHOWN
(see Figure 7, Page 9)
NOTE: Power Connections NOT SHOWN
(see Figure 7, Page 9)
12
AD1200EXP to Pan/Tilt Site Connection
The AD1200EXP provides connection ports to four pan/tilt
units via 14-pin connectors.
NOTE: The AD1200EXP does not provide power to either
the pan/tilt or the camera.
1. Using Table 4 as reference, connect each lead from the
pan/tilt unit to the appropriate terminal of the 14-pin
connector (see Figure 9).
2. Tighten the clamp-screw on the top of the connector as
each lead is inserted into the terminal.
3. After tightening the clamp-screw, gently pull on the wire
to verify that it is securely held in place.
4. Attach the 14-pin connector to the appropriate mating
connector (location 1, 2, 3, or 4) on the AD1200EXP rear
panel.
Cable Selection
Table 5 lists the recommended AWG wire size -vs- the
maximum distance between the AD1200EXP and a pan/tilt
unit.
TABLE 5 - Recommended Wire Gauge
AWG Distance Distance
1000mA 500mA
16* 400 ft/121.9m 800 ft/243.8m
18* 250 ft/76.2m 500 ft/152.4m
20* 160 ft/48.8m 315 ft/96m
22* 100 ft/30.5m 200 ft/61m
* Distances are based on solid copper wire, single common, and worst
case current draw (i.e. diagonal pan/tilt operation).
INSTALLATION AD1200EXP
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
AD1200EXP Port Expander
Function
Tilt UP
Tilt DOWN
Pan RIGHT
Pan LEFT
Aux 1
Aux 2
No Connection
24VAC COMMON
Lens COMMON
Lens IRIS
Lens FOCUS
Lens ZOOM
No Connection
No Connection
Pan/Tilt Unit
Function
Tilt UP
Tilt DOWN
Pan RIGHT
Pan LEFT
Aux 1 (if equipped with auxiliaries)
Aux 2 (if equipped with auxiliaries)
- - - - - - - - - - - -
24VAC/Aux COMMON
Lens COMMON
Lens IRIS
Lens FOCUS
Lens ZOOM
- - - - - - - - - - - -
- - - - - - - - - - - -
Table 4 - AD1200EXP -to- Pan/Tilt Connection
CAUTION
Disconnect the AD1200EXP and the pan/tilt
units from their respective power sources before
proceeding with any connections! Severe
damage to the internal electronics as well as
personal injury may result!
!
13
AD1200EXP INSTALLATION
1 2 3
4
U D R L 1 2 R C I
F Z
N
C
N
C
N
C
0 1 2 3 G
12
3
4
AD1200EXP
U D R L 1 2 R C I
F Z
N
C
N
C
N
C
AD1240 Pan/Tilt
U D R L 1 2 R C I F Z
N
C
N
C
N
C
1
ZOOM
FOCUS
IRIS
LENS COMMON
UP
DOWN
RIGHT
LEFT
U D R L 1 2 R C I F Z
N
C
N
C
N
C
3
ZOOM
FOCUS
IRIS
COMMON
UP
DOWN
RIGHT
LEFT
AD1240 Pan/Tilt
AUX 1
AUX 2
AUX 1
AUX 2
PAN/TILT RETURN
AUX RETURN
PAN/TILT RETURN
AUX RETURN
Figure 9 - Pan/Tilt -to- AD1200EXP Connection
14
CCTV Switcher System Connection
AD1200EXP units provide a 5-pin connector for use with
CCTV switcher systems. Each AD1200EXP unit is provided
with one 5-pin strap harness and two 5-pin mating connectors.
AD1200EXP to AD1412 Series Switcher Connection
The AD1200EXP is designed for complete operating
compatibility with the AD1412 and AD1412L Sequential
Switchers.
1. Cut the 5-pin connector from one end of the 5-pin strap
harness.
2. Using Table 6 as reference, connect each lead from the 5-
pin strap harness to the appropriate terminal of the 12-pin
connector provided with the AD1412/AD1412L
(see Figure 10).
INSTALLATION AD1200EXP
AD1200EXP
1 2 3
4
U D R L 1 2 R C I F
Z
N
C
N
C
N
C
1
2
3
4
0 1 2 3 G
U D R L 1 2 R C I F
Z
N
C
N
C
N
C
CAMERA ID 0#
CAMERA ID 1#
2 31
4
65
10 11 12
7 8
9
J15
GROUND
CAMERA
120V
60Hz
OUTP UT
A
B
12 34 56 78 910 11 12
AD1412 w/Terminated Rear Panel
AD1412L w/Looping Rear Panel
120V
60Hz
CAMERA
J1 J2
MONITOR
A
B
1 2 3 4 5 6 7 8 9 10 11 12
CAMERA ID 2#
0 1 2 3 G
J1 6
J1 5
CAMERA ID 3#
Figure 10 - AD1200EXP -to- AD1412/AD1412L Sequential Switcher Connection
Pin #
0
1
2
3
G
Function
Camera ID #0
Camera ID #1
Camera ID #2
Camera ID #3
GROUND
Function
Camera ID #0
Camera ID #1
Camera ID #2
Camera ID #3
GROUND
Pin #
2
3
4
5
1
Table 6 - AD1200EXP -to- AD1412/AD1412L Pin Functions
AD1200EXP
AD1412
AD1412L
15
AD1200EXP INSTALLATION
120V
60Hz
120V
60Hz
J1 J2
J2J1
AD1416L w/Looping Rear Panel
MONITOR
A
B
CA MERA
J3
MONITOR
AB
CA MERA
1234 56789101112 14151613
J3
AD1416 w/Terminated Rear Panel
123456789101112 14151613
AD1200EXP
1 2 3
4
U D R L 1 2 R C I F
Z
N
C
N
C
N
C
1
2
3
4
0 1 2 3 G
U D R L 1 2 R C I F
Z
N
C
N
C
N
C
CAMERA ID 0#
CAMERA ID 1#
2 31
4
65
10 11 12
7 8
9
J2
GROUND
CAMERA ID 2#
0 1 2 3 G
CAMERA ID 3#
Figure 11 - AD1200EXP -to- AD1416/AD1416L Sequential Switcher Connection
AD1200EXP to AD1416 Series Switcher Connection
The AD1200EXP is designed for complete operating
compatibility with the AD1416 and AD1416L Sequential
Switchers.
1. Remove the 5-pin connector from one end of the 5-pin
strap harness.
2. Using Table 7 as reference, connect each lead from the 5-
pin strap harness to the appropriate terminal of the 12-pin
connector provided with the AD1416/AD1416L (see
Figure 11).
Pin #
0
1
2
3
G
Function
Camera ID #0
Camera ID #1
Camera ID #2
Camera ID #3
GROUND
Function
Camera ID #0
Camera ID #1
Camera ID #2
Camera ID #3
GROUND
Pin #
2
3
4
5
1
Table 7 - AD1200EXP -to- AD1416/AD1416L Pin Functions
AD1416
AD1416L
AD1200EXP
16
SETUP
4-Position DIP Switch
A 4-position DIP switch configures the AD1200EXP for the
number of operational cameras and for use within a CCTV
switching system. The 4-position DIP switch is mounted on
the AD1200EXP rear panel (see Figure 12).
Using Table 8 as reference, read the following descriptions of
each of the four DIP switches.
DIP Switch #1 - Used in conjunction with DIP switch #2 for
addressing camera groups. Refer to Table 9
for specific camera group DIP switch settings.
DIP Switch #2 - Used in conjunction with DIP switch #1 for
addressing camera groups. Refer to Table 9
for specific camera group DIP switch settings.
DIP Switch #3 - Enables or disables the internal circuitry
required for CCTV switching system
operation.
DIP Switch #4 -
Not used.
SETUP AD1200EXP
U D R L 1 2 R C I
F Z
N
C
N
C
N
C
U D R L 1 2 R C I
F Z
N
C
N
C
N
C
1
2
3
4
1 2 3 4
4-Position DIP Switch
AD1200EXP
ON
OFF
Figure 12 - 4-Position Dip Switch
DIP Switch #
1
2
3
4
Function
ON
Camera ID
Camera ID
Switcher Enabled
Not Used
Function
OFF
Camera ID
Camera ID
Switcher Disabled
Not Used
Table 8 - AD1200EXP DIP Switch Functions
Camera Group 1-4
Camera Group 5-8
Camera Group 9-12
Camera Group 13-16
DIP Switch #1
Off
On
Off
On
DIP Switch #2
Off
Off
On
On
Table 9 - AD1200EXP DIP Switch Settings
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
