Cree ESSENTIA ESA-ADR-414 Installation guide

Brand: Cree

Model: ESSENTIA ESA-ADR-414

Type: Installation guide

Cree ESSENTIA ESA-ADR-414 is a versatile and high-performance 4-inch downlight that offers exceptional illumination for various applications. With its adjustable mounting height, this downlight can be tailored to fit different ceiling thicknesses, ensuring a flush and seamless integration. Its thermally protected design prevents overheating, allowing for safe and reliable operation even in enclosed spaces.

The ESSENTIA ESA-ADR-414 is equipped with advanced dimming capabilities, supporting both 0-10V DC low voltage dimming and Lutron 3-wire and EcoSystem Digital dimming protocols. This dimming functionality provides precise control over light intensity, enabling you to create the desired ambiance and save energy.

ESSENTIA®

4-INCH DOWNLIGHT AND 6, 8-INCH WALL WASH

Includes: ESA-ADR/ADS-414, ESA-ADR/ADS-614/828

INSTALLATION INSTRUCTIONS

1 of 2 KI071X01R2

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed

including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. To reduce the risk of electrical shock, turn off power supply before installation or

servicing.

2. This luminaire must be installed in accordance with the NEC or your local electrical

code. If you are not familiar with these codes and requirements, consult a qualied

electrician.

3. This xture must be supported by main runners or other building structure that is capable

of supporting xture weight.

4. These xtures are thermally protected. Do not install insulation within 3 inches (76 mm)

of xture sides or junction box nor above xture in such a manner as to entrap heat.

5. Blinking LED may indicate xture is too close to insulation.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

TO INSTALL:

LUMINAIRE INSTALLATION

STEP 1:

Cut appropriate sized hole in ceiling

Luminaire

Type

Ceiling Cutout

Size

Luminaire

Weight

4 in round

downlight 4-3/4 in. 10 lbs.

4 in square

downlight 5x5 in. 10 lbs.

6 in round

wall wash 7 in. 11 lbs.

6 in square

wall wash 6-1/2 x 6-1/2 in. 11 lbs.

8 in round

wall wash 8-3/4 in. 13 lbs.

8 in square

wall wash 8-1/2 x 8-1/2 in. 13 lbs.

STEP 2:

Be sure to orientate the Wall Wash

housing correctly, as indicated by the

“Point Arrow At Wall” label.

STEP 3:

Thread rigid conduit, bar stock, wire or

C-channel (supplied by others) through

quick-mount brackets at the sides of the

ﬁxture.

STEP 4:

Attach mounting means to structure or

other adequate support.

STEP 5:

Adjust mounting height by loosening

adjustment nuts on Quick Mount Brackets,

then position bracket so that the bottom

of the plaster ring is ﬂush with the bottom

of the opening of the ﬁnished ceiling. (See

Figure 1)

STEP 6:

Tighten adjustment nut(s).

STEP 7:

Remove junction box cover and bring in

appropriate power supply to the junction

box using one of the knock-outs.

STEP 8:

Wire ﬁxture per “Wiring Instructions”

section.

NOTE: Fixture is intended to be wired to

a speciﬁc voltage. Make sure that supply

voltage matches voltage on electrical

label next to the junction box. Connecting

ﬁxture to voltage other than that speciﬁed

on the label may result in ﬁxture damage

and/or improper ﬁxture operation.

WIRING INSTRUCTIONS

When wiring a non-dimming luminaire:

1. Connect supply ground wire to

ﬁxture ground (green).

2. Connect supply line conductor to

ﬁxture hot (black).

3. Connect supply neutral conductor to

ﬁxture neutral (white).

When wiring a luminaire for dimming

with the BetaLED driver

(0-10V DC low voltage dimming

control) See Figure 2.

Hot (black)

Neutral (white)

Ground (green)

LED

Driver

-V

LED

Light

Engine

To line

Voltage

Dim + (violet)

Dim - (violet)

To Dimming

Control

Adjustment Nut

on Quick Mount

Bracket

Plaster Ring

2 of 2 KI071X01R2

www.cree.com/lighting

See www.cree.com/lighting for warranty and speciﬁcations. Cree® and the Cree logo are registered

trademarks.

Switched Hot (black)

Dimmed Hot (orange)

Neutral (white)

Ground (green)

LED

Driver

-V

LED

Light

Engine

To Dimming

Control

Hot (black)

Neutral (white)

Ground (green)

LED

Driver

-V

LED

Light

Engine

To line

Voltage

E1 (violet)

E2 (violet)

To EcoSystem

Bus

When wiring a luminaire for Lutron

3-wire dimming, See Figure 3.

When wiring a luminaire for Lutron

EcoSystem Digital, See Figure 4.

Control:

NOTE: If power limited circuit wiring is

being used for the dimming connections,

use the Class 2 kit and instruction sheet

included with the luminaire when wiring.

FIXTURE SERVICING AND

MAINTENANCE

Patented SlideWays™ feature: This feature

can be used to access the luminaires’ j-box

or LED Driver(s) from below the ceiling.

Follow the directions below and refer to

Figures 5 and 6 for instructions.

STEP 1:

Remove the trim from ﬁxture.

STEP 2:

To slide the lamp housing out of the way

from below the ceiling, pull down on the

spring release bracket (shown in Figures

5 and 6) and slide the recessed housing

towards the spring release bracket.

STEP 3:

When ﬁnished with servicing or

maintenance, slide the recessed housing

back into original position (until spring

release bracket snaps back into place).

Spring Release Bracket

Slide This Way

Recessed Housing Junction Box

Power Supply

Cree ESSENTIA ESA-ADR-414 Installation guide

Cree ESSENTIA ESA-ADR-414 Installation guide

Cree ESSENTIA ESA-ADR-414 Installation guide

Related papers

Other documents