Sunco Lighting Disk LED Downlight (15W) Installation guide

Sunco Lighting
Brand
Sunco Lighting
Model
Disk LED Downlight (15W)
Type
Installation guide
The Brighter Choice
WARNING SPECIFICATIONS
SURFACE MOUNT-JUNCTION BOX
1.
3.
7.
2
8.
Voltage
Wattage
Damp
Polycarbonate
0.39lbs
7 years
120V
15W
Housing
Weight
Warranty
Suitable for Locations Ingress
All electrical connections must be in accordance with local and National Electric
Code (N.E.C.) standards. Consult a qualified electrician if you are unfamiliar with
proper electrical wiring connections. Please review these instructions carefully
before proceeding.
WARNING: Risk of fire or electric shock. Do not alter, relocate or remove wiring
during installation.
WARNING: Do not make or alter any open holes in an enclosure of wiring or
electrical components during kit installation
Turn off circuit breaker that provides power to the
light switch for the recessed lights.
• This fixture is compatible with a 4 inch and 6 inch
junction box.
Connect the supply wires to the junction box
wires using the wire nuts provided.
• White to white
• Green to green
• Black to black
Complete the installation by screwing the lens
back into place (counter clockwise).
Remove the lens by twisting clockwise.
Turn on circuit breaker and test the light.
Turn Power OFF Lens
4.
5.
6.
Tuck the connected wires inside the junction box.
Align junction box with holes on the fixture that
correspond to the size (4” or 6”).
Attach the fixture to the junction box with either
short or long screws pending on the junction box
(deep or shallow). DO NOT OVER TIGHTEN.
Turn Power ON
Install Guide and Manual
COMPONENTS
EASY INSTALLATION
TP24 Connector Clips Wire Nuts Screws
DISK 15W LED DOWNLIGHT
The Brighter Choice
Install Guide and Manual
COMPONENTS
EASY INSTALLATION RETROFIT INSTALLATION-CAN
1.
2.
4.
6.
10.
11.
7.
3.
5.
8.
9.
12.
Turn off circuit breaker that provides power to the
light switch for the recessed lights.
Locate the housing.
• Remove previous fixture, fixture may be hot so
allow time to cool after turning off power.
Place the springs into the keyhole slots on the back
of the fixture using the Metric screws provided.
Using a screwdriver, gently tighten in place.
• Slot placement should be chosen based on can
size (5” or 6”).
Connect the TP24 adapter to the TP24 connector
inside the recessed can.
Attach ground wire to the grounding screw located
inside the can.
Push disk into recessed can until secure
Complete the installation by screwing the lens back
into place (counter clockwise).
Turn on circuit breaker and test the light.
Remove the lens by twisting clockwise.
Connect the supply wires to the TP24 adapter wires
using the wire nuts provided.
• White to white
• Black to black
• It is highly recommended that a licensed electrician
installs the ground wire to the box, if not already
included in your existing can.
Pinch springs and line up trim ring with opening.
Hook disk springs into housing.
• Strong springs. Use caution when compressing
springs to fit inside can. Springs can bounce back
quickly and cause injury.
Turn Power OFF
TP24
Connector
Wire Nut
Lens
Spring
slots
TP24 Connector Clips Wire Nuts Screws
DISK 15W LED DOWNLIGHT
Spring
Holder
Metric
Screws
Wire Nut
Turn Power ON
  • Page 1 1
  • Page 2 2

Sunco Lighting Disk LED Downlight (15W) Installation guide

Sunco Lighting
Brand
Sunco Lighting
Model
Disk LED Downlight (15W)
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents