WAC Lighting FM-306-930JB-WT Installation guide
- Type
- Installation guide
This manual is also suitable for
WAC Lighting FM-306-930JB-WT
is a high-quality LED light fixture designed for use in a variety of commercial and residential applications. With its sleek design and powerful LED technology, the FM-306-930JB-WT provides bright, even illumination while saving energy.
The FM-306-930JB-WT is easy to install and can be used in a variety of mounting configurations, including recessed, surface-mounted, and pendant.
The product also features a variety of dimming options which make it a great option for applications where you need to control the level of light as well as color temperature.
Here are some of the key features and benefits of the WAC Lighting FM-306-930JB-WT:
WAC Lighting FM-306-930JB-WT
is a high-quality LED light fixture designed for use in a variety of commercial and residential applications. With its sleek design and powerful LED technology, the FM-306-930JB-WT provides bright, even illumination while saving energy.
The FM-306-930JB-WT is easy to install and can be used in a variety of mounting configurations, including recessed, surface-mounted, and pendant.
The product also features a variety of dimming options which make it a great option for applications where you need to control the level of light as well as color temperature.
Here are some of the key features and benefits of the WAC Lighting FM-306-930JB-WT:
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER 2, 2015 12:02 PM
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
LED DISC
FM-304
WARNING
IMPORTANT: NEVER attempt any work without shutting off the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or
switch ”OFF” the circuit breaker switch(es) that control the power to the fixture or room that you are working on.
- Place the wall switch in the “OFF” position.
- Supply conductors (Power Wires) Connecting the fixture must be rated minimum 90°C. If uncertain, consult an electrician.
CAUTIONS
- These luminaires (fixtures) are designed to meet the latest NEC requirements.
- Before attempting installation, check your local electrical code, as it sets the wiring standards for your locality.
Fig. 1
1. Twist lens cover counter-clockwise to remove from Disk Light.
2. Install cross bar to the 4” junction box with junction box screw.
ELECTRICAL CONNECTION
3. Provide electrical service according to the “National Electrical
Code” or your local electrical code to the outlet box.
4. Connect supply wires to fixture wires and insulate with proper
size wire nuts (Fig 1).
a) Connect incoming ground wire (green or bare) to fixture
ground wire (green or bare).
b) Connect incoming common (white) wire to fixture common
(white).
c) Connect incoming hot (typically black) wire to fixture
black wire.
5. Attach the fixture to the cross bar and outlet box by fastening
supplied 1½” outlet box screws through canopy keyholes. Make
sure Disk Light is flush to the ceiling. (Fig. 1)
6. Twist the lens clockwise on disc light metal enclosure and lock
the lens in place.
Outlet Box (not included)
Mounted Screw
Cross bar needed only
for 4” junction box
Keyholes
Disc Light
Ground
White
Black
Lens
INSTALLATION
Over standard electrical junction box
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER 2, 2015 12:02 PM
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
LED DISC
FM-304
1. Twist lens cover counter-clockwise to remove from Disk Light.
2. Attach plastic insert to Disk Light using supplied ¼” screws.
(Fig. 2)
3. Detach the orange connector from socket adapter and insert
black and white fixture wire into non-wired half of orange
connector following color code marked. (Fig. 3)
4. Screw the socket adapter to socket in housing. (Fig. 4)
5. Plug the female connector of the disc light onto the male
connector of the socket adapter assembly. (Fig. 4)
6. Push Disk Light through hole in plaster frame until flush
with ceiling. Spring clip tension can be adjusted by bending
spring clip.
7. Replace the lens back on to the Disk Light by twist the lens
counter clockwise.
HOUSING COMPATIBILTY
Brand Model
Halo® H99T, H99RT, H99ICT
All-Pro ET400, ET400R, ET400AT
Juno® TC1, TC1R, IC1P
Capril R4, RR4, R4ASIC
Lithonia® L3, L3R
Thomas® PS4, PS4RM, PS4ASIC
Fig. 2
Fig. 3
Fig. 4
Installation onto existing 4 inch recessed housings
Plastic Insert
¼” screws
WAC Lighting
www.waclighting.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. AUGUST 3, 2015 5:28 PM
INSTALLATION INSTRUCTION
LED DISC
FM-306
WARNING
IMPORTANT: NEVER attempt any work without shutting off the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or
switch ”OFF” the circuit breaker switch(es) that control the power to the fixture or room that you are working on.
- Place the wall switch in the “OFF” position.
- Supply conductors (Power Wires) Connecting the fixture must be rated minimum 90°C. If uncertain, consult an electrician.
CAUTIONS
- These luminaires (fixtures) are designed to meet the latest NEC requirements and are listed in full compliance with UL 1598.
- Before attempting installation, check your local electrical code, as it sets the wiring standards for your locality.
Fig. 1
1. Attach two mounted screws into outlet box leaving enough of
screw exposed to engage keyholes in the top of disc light
(Fig. 1).
2. Provide electrical service according to the “National Electrical
Code” or your local electrical code to the outlet box.
3. Connect supply wires to fixture wires and insulate with proper
size wire nuts (Fig. 1).
4. Connect incoming ground wire (green or bare) to fixture ground
wire (green or bare).
5. Connect incoming common (white) wire to fixture common
(white).
6. Connect incoming hot (typically black) wire to fixture black wire.
7. Raise the disc light to the junction box and tighten screws.
LENS INSTALLATION
Twist the lens clockwise on disc light metal enclosure and lock the
lens in place.
Outlet Box (not included)
Mounted Screw
Keyholes
Disc Light
Ground
Lens
INSTALLATION
Over standard electrical junction box
WAC Lighting
www.waclighting.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. AUGUST 3, 2015 5:28 PM
1. Screw E26 “medium screw base” socket adapter into socket
in housing. (Fig. 2)
2. Plug the female connector of the disc light onto the male
connector of the socket adapter assembly. (Fig. 3)
3. Squeeze the torsion springs together as shown and install into
torsion spring brackets inside the housing. (Fig. 4)
4. Tuck all wires into to the housing and carefully push the disc
light into housing. (Fig. 4)
LENS INSTALLATION
Twist the lens clockwise on disc light metal enclosure and lock the
lens in place.
INSTALLATION INSTRUCTION
LED DISC
FM-306
Fig. 2
Fig. 4
Caution
Make sure that tab in bracket should be positioned inward.
Fig. 3
Torsion Springs
TAB
Disc
Installation onto existing 5 inch or 6 inch recessed housings
-
1
-
2
-
3
-
4
WAC Lighting FM-306-930JB-WT Installation guide
- Type
- Installation guide
- This manual is also suitable for
WAC Lighting FM-306-930JB-WT
is a high-quality LED light fixture designed for use in a variety of commercial and residential applications. With its sleek design and powerful LED technology, the FM-306-930JB-WT provides bright, even illumination while saving energy.
The FM-306-930JB-WT is easy to install and can be used in a variety of mounting configurations, including recessed, surface-mounted, and pendant.
The product also features a variety of dimming options which make it a great option for applications where you need to control the level of light as well as color temperature.
Here are some of the key features and benefits of the WAC Lighting FM-306-930JB-WT:
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
WAC Lighting FM-240203 Operating instructions
-
-
-
-
-
-
-
WAC Lighting HT8-WT Installation guide
-
-
Other documents
-
Modern Forms WS-62110 Cymbal Operating instructions
-
-
-
-
-
-
-
-
-