Grace Company Grace Speed Control Operating instructions

Brand
Grace Company
Model
Grace Speed Control
Type
Operating instructions

Grace Company Grace Speed Control is designed to work with Juki sewing machines. It allows you to set your machine to the desired stitch speed, ranging from slow to full speed. The front panel has a speed control knob, an on/off button, and a pulse button. The back panel has a plastic cover that can be opened to access the jumper plugs. The jumper plugs must be set to the correct position for your sewing machine model.

Here are some of the features and possible use cases of the Grace Company Grace Speed Control:

  • Set your machine to the desired stitch speed for different fabrics and projects.

Grace Company Grace Speed Control is designed to work with Juki sewing machines. It allows you to set your machine to the desired stitch speed, ranging from slow to full speed. The front panel has a speed control knob, an on/off button, and a pulse button. The back panel has a plastic cover that can be opened to access the jumper plugs. The jumper plugs must be set to the correct position for your sewing machine model.

Here are some of the features and possible use cases of the Grace Company Grace Speed Control:

  • Set your machine to the desired stitch speed for different fabrics and projects.
Sewing machine
does not turn
on when speed
control on/
of button is
pushed in.
• Verify the Speed Control sewing
cable is plugged into the sewing
machine foot pedal connector.
• Verify the sewing machine power
switch is in the on position.
• Verify the sewing machine cord is
plugged in correctly.
• Adjust Speed Control knob to 1/4
turn CW.
Sewing machine
does not work
correctly with
this Speed
Control.
Verify your sewing machine is one of
the Juki models shown in Table 1. If
your sewing machine is a different
model please refer to the Grace
Company contact information at the
bottom of this page.
Juki TL2010Q
Sewing machine
will not turn on.
refer to Table 1 and verify the
jumper plug position is correct.
Juki TL98Q, TL98QE
Power On/Off
does not work
consistently.
Refer to Table 1 and verify jumper
plug position is correct.
Excessive Idle
Speed.
Use only the cable that was shipped
with the Speed Control. Some cables
may
but may cause the Speed
Control to operate incorrectly
Juki TL98E
Cutter does
not work
consistently
Refer to Table 1 and verify jumper
plug position is correct
Grace Speed Control
The Grace Speed Control is designed
to work with Juki sewing machines.
Setting Up Your Speed Control-
SC-1: Open The plastic cover on the back
panel.
SC-2: Using Table 1, verify that your jumper
plug is in the correct position for your sewing
machine.
SC-3: If in wrong position, remove and
reposition the jumper plug to match your
sewing machines.
SC-4: Reinstall the plastic cover and install
your Speed Control.
Speed Control-
Allows you to set
your machine to
desired stitch-speed
ranging from slow to
full speed.
Pulse Button-
Machine stops
when you
release, or use
for single stitch.
On/Off-
Press for on,
press again for
off
Front Panel
Jack Plug-In
Jack Plug-In Adapter
Jack Plug-In
(To Sewing Machine)
(To Speed Control Jack)
Back Panel
Plastic Cover
Jumper Plugs
Juki Sewing Machine Jumper Plug Position
TL2010Q, TL98Q, TL98QE
Table 1
Trouble Shooting:
After reviewing all troubleshooting steps and
your Speed Control still does not work please
call Grace Company at 1-800-264-0644. If
you are using a different sewing machine
please go to the Grace Company web site
www.graceframe.com to see if we have a Speed
Control compatible with your sewing machine.
Copyright January 1, 2016
Jim M. Bagley, GraceWood, Inc
(Reproduction Prohibited)
Version 2.1
(TL2010Q)
(TL98Q, TL98QE)
  • Page 1 1

Grace Company Grace Speed Control Operating instructions

Brand
Grace Company
Model
Grace Speed Control
Type
Operating instructions

Grace Company Grace Speed Control is designed to work with Juki sewing machines. It allows you to set your machine to the desired stitch speed, ranging from slow to full speed. The front panel has a speed control knob, an on/off button, and a pulse button. The back panel has a plastic cover that can be opened to access the jumper plugs. The jumper plugs must be set to the correct position for your sewing machine model.

Here are some of the features and possible use cases of the Grace Company Grace Speed Control:

  • Set your machine to the desired stitch speed for different fabrics and projects.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents