Danfoss SpeedUp Eco - Strongboard tile and laminate User guide

Danfoss
Brand
Danfoss
Model
SpeedUp Eco - Strongboard tile and laminate
Type
User guide

Danfoss SpeedUp Eco - Strongboard tile and laminate.

Strongboard tile and laminate is a versatile construction system that can be used for a variety of applications and excels specifically in the installation of tiles and laminates with a thickness larger than 8mm. The panels are lightweight and easy to install, making them ideal for both new construction and renovation projects.

Some of the key features of Strongboard tile and laminate include:

  • High load-bearing capacity: The panels can withstand loads of up to 2 kN/m², making them suitable for use in areas with heavy foot traffic.

Danfoss SpeedUp Eco - Strongboard tile and laminate.

Strongboard tile and laminate is a versatile construction system that can be used for a variety of applications and excels specifically in the installation of tiles and laminates with a thickness larger than 8mm. The panels are lightweight and easy to install, making them ideal for both new construction and renovation projects.

Some of the key features of Strongboard tile and laminate include:

  • High load-bearing capacity: The panels can withstand loads of up to 2 kN/m², making them suitable for use in areas with heavy foot traffic.
Application sheet
SpeedUp Eco
Tile / natural stone
Strongboard tile and laminate
1
2
3
4
5
1 Tile / natural stone incl. adhesive ≥ 12 mm
2 Strongboard tile and laminate 5 mm
3 SpeedUp Eco heat panel + FH composite pipe 30 mm
4 Support batten (30mm)
5 Load bearing panel 22 mm
6 Wood bre insulation - additional insulation 20 mm
7 SpeedUp Eco perimeter insulation
8 If necessary moisture barrier
Floor nish ≥ 8 mm Tile dimensions: min. 10 x 10 cm; max. 40 x 60 cm;
Natural stone thicknesses from 10 mm; Grout width 3 mm
Construction height ≥ 89 mm Height including oor nish
Weight ~ 53 kg / m² Weight including oor nish
Thermal resistance R 1,32 m²K / W The minimum thermal resistance requirement of DIN EN 1264 is
fullled.
Thermal transmission coecient U 0,67 W / m²K If the architectural design species better thermal insulation, this
must be taken into account.
Design load ≤ 2,0 kN / m²
Point load (≥ 20 cm²) ≤ 1,0 kN Sum point load ≤ design load; please notice special heavy ob-
jects (aquaria etc.)
Impact subsonic noise reduction 22 dB Test value according to DIN ISO 140-8; applies to concrete slabs
thicker than 12 cm (DIN 4109: m’ > 276 kg/m²)
Application area
Residential spaces, hallways and attic spaces in residential buildings and hotel rooms.
Corresponds to categories A1, A2 and A3 of DIN 1055-3.
Requirements & special features
Structural sealing according to DIN 18195 must be placed beneath the oor panel in case
of structures facing the ground, and otherwise on the unnished oor. The R value must
be increased if the groundwater level is less than or equal to 5 m. A U value not exceed-
ing 0.5 W/m²K must be maintained in existing buildings and additions with areas up to
50 m². Wooden joist oor, free from twist eects, free of deection Strongboard is only
approved for use with Danfoss components. Lay tiles using the combined method with
Mapei adhesive and Elastorapid (see installation instructions). Observe all installation
instructions and manufacturer’s instructions.
Additional insulation
20 mm wood bre insulation 150kPa, renovation: 50 mm wood bre insulation 150 kPa,
WLG 050
Construction
According to EnEV, EN 1264, DIN 1055, 4108 and 18202
Construction number 99
Technical Data Floors/ceilings facing unheated rooms or the ground
6
7
8
© Danfoss 11/2008
VA.CS.S1.02
Danfoss HES
  • Page 1 1

Danfoss SpeedUp Eco - Strongboard tile and laminate User guide

Danfoss
Brand
Danfoss
Model
SpeedUp Eco - Strongboard tile and laminate
Type
User guide

Danfoss SpeedUp Eco - Strongboard tile and laminate.

Strongboard tile and laminate is a versatile construction system that can be used for a variety of applications and excels specifically in the installation of tiles and laminates with a thickness larger than 8mm. The panels are lightweight and easy to install, making them ideal for both new construction and renovation projects.

Some of the key features of Strongboard tile and laminate include:

  • High load-bearing capacity: The panels can withstand loads of up to 2 kN/m², making them suitable for use in areas with heavy foot traffic.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents