Highpoint SSD7110 Quick Installation Guide

Type
Quick Installation Guide
1
SSD7110
Hybrid Connectivity M.2 + SAS/SATA Ports, All-in one
RAID Controller
Quick Installation Guide
V1.00
2
System Requirements
PC Requirements
System with an empty x16 PCIe 3.0 slot
Windows 10 or later
Linux Kernel 3.19 or later
SSD7101A Hardware
Front View
3
NVMe Drive Installation:
Step 1. On the rear of the SSD7110, remove the six screws that secure the unit’s
front panel to the PCB.
After removing the screws, carefully remove the front panel from the
SSD7110.
Step 2. These 3 screws are used to install the NVMe SSD’s.
4
Step 3. The SSDs should be installed from top to bottom. Remove the
top screw.
Step 4. Gently insert the SSD into the slot.
5
Step 5. Refasten the screw to secure the SSD.
Repeat Steps 3 to 5 to install the remaining SSDs.
Step 6. Replace the front panel after installing all SSDs
Step 7. On the rear of the SSD7110, refasten the 6 screws that were
removed in step 1.
SAS/SATA Drive Installation
SSD7110 has four SFF-8643 Ports. Please connect the SAS/SATA
drives via SFF-8643 to SAS/SATA cables.
Comment [JY1]: Updated
6
Setting up the SSD7110 for a Windows operating system
1. Verifying Installation
After booting Windows, open Device Manager, and expand Disk drives.
The installed NVMe drive should be displayed:
2. Driver Installation
1) Download the Windows driver package from the HighPoint website:
http://www.highpoint-tech.com/USA_new/series-ssd7110-download.
htm
2) Once downloaded, locate the folder you downloaded the driver to.
Extract the driver package. There are two driver packages .exe file for
the SSD7110. Please install the driver package one by one:
3) Double click.exe file to start the driver installation.
4) Follow the wizard and reboot system to complete the driver
installation.
5) After rebooting, a RocketNVME RAID Controller and a SSD711X
RAID Controller entry should be displayed under Storage
Controllers:
Comment [H2]: Updated (7/8/19)
Comment [JY3]: Updated
Comment [JY4]: Updated
7
3. Installing the HighPoint RAID Manager(HRM)
The HighPoint RAID Manager is used to configure and monitor the
SSD7110. Download the HighPoint RAID Manager software package from
the HighPoint website:
http://www.highpoint-tech.com/USA_new/series-ssd7110-download.htm
1) Extract the package and double-click the setup.exe program to install
the software.
2) After the installation, start HighPoint RAID Manager by double
clicking the ICON on the desktop:
3) The SSD7110s NVMe and the SAS/SATA drives are managed by
different controllers. You can switch between and manage both
controllers using HighPoint RAID Manager:
4) Please consult the complete User’s Guide for more information about
the HighPoint RAID Manager.
Comment [H5]: Updated 7-8-19 by Alan
Madzar
Comment [JY6]: Updated
Comment [JY7]: Updated
Comment [JY8]: UPdated
8
Setting up the SSD7110 for a Linux Distribution
Please download the Linux Software Package from the HighPoint
Website:
http://www.highpoint-tech.com/USA_new/series-ssd7110-download.htm
Please follow the Linux Installation guide included with the software
package the software package to install and setup the SSD7110.
Customer Support
If you encounter any problems while utilizing the SSD7100 drive, or
have any questions about this or any other HighPoint Technologies, Inc.
product, feel free to contact our Customer Support Department.
Web Support: http://www.highpoint-tech.com/websupport/
HighPoint Technologies, Inc. websites:
http://www.highpoint-tech.com
© Copyright 2017 HighPoint Technologies, Inc. All rights reserved.
Comment [H9]: Updated 7-8-19
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Highpoint SSD7110 Quick Installation Guide

Type
Quick Installation Guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI