Highpoint SSD7120 Quick Installation Guide

Type
Quick Installation Guide

Highpoint SSD7120, a NVMe U.2 RAID controller, is compatible with PCIe 3.0 x16 slots and supports NVMe SSDs via SFF-8643 to U.2 cables or an NVMe backplane. It's well-suited for Windows 10, Windows Server 2012 R2 and 2016, and Linux distributions with Kernel 3.3 or later. This device empowers you with the ability to configure NVMe SSDs into RAID arrays for enhanced performance and data protection in your storage system.

Highpoint SSD7120, a NVMe U.2 RAID controller, is compatible with PCIe 3.0 x16 slots and supports NVMe SSDs via SFF-8643 to U.2 cables or an NVMe backplane. It's well-suited for Windows 10, Windows Server 2012 R2 and 2016, and Linux distributions with Kernel 3.3 or later. This device empowers you with the ability to configure NVMe SSDs into RAID arrays for enhanced performance and data protection in your storage system.

1
SSD7120
NVMe U.2 RAID Controller
Quick Installation Guide
V1.02
2
System Requirements
System Requirements
System with an empty PCIe 3.0 x16 slot
SSF-8643 to U.2 Cable or SFF-8643 cable with NVMe backplane
Windows 10
Windows Server 2012 R2 and 2016
Linux Kernel 3.3 or later
SSD7120 Hardware Overview
Front View
3
Hardware Installation:
1. Remove the system cover.
2. Insert the SSD7120 card into an open PCI-E 3.0 x16 slot on the
motherboard.
3. After you have inserted the SSD7120 card, you can connect the
SFF-8643 cables.
4. Connect the SSD7120 to the NVMe SSD’s using the appropriate
SFF-8643 cables.
5. Replace the system cover and power up the system.
Note: Please be sure to connect NVMe before using the product to
reduce the occurrence of unnecessary errors!
Note: Install the driver in the system first and then install the board
4
Setting up the SSD7120 for a Windows operating system
1. Verifying Installation
After booting Windows, open Device Manager, and expand Disk drives.
The installed NVMe Drive should be displayed:
2. Driver Installation
1) Download the Windows driver package from the HighPoint website:
http://www.highpoint-tech.com/USA_new/series-ssd7120-
download.h tm
2) Once downloaded, locate the folder you downloaded the driver to.
Extract the driver package and double click the setup.exe file to start
the driver installation procedure.
3) Follow the wizard and reboot the system to complete driver
installation.
4) After rebooting, a HighPoint NVME RAID Controller entry
should be displayed under Storage Controllers.:
5
3. Installing the HighPoint RAID Manager
The HighPoint RAID Manager is used to configure and monitor the
SSD7120 RAID controller and hosted NVMe SSD’s. Download the
HighPoint RAID Manager software package from the HighPoint website:
http://www.highpoint-tech.com/USA_new/series-ssd7120-download.htm
1) Extract the package and double-click the setup.exe program to install
the software.
2) The software can be used to configure NVMe SSD’s into one or
more RAID configurations. Please consult the full user manual for
more details.
3) After the RAID is configured, open the OS Disk Management utility
and check to make sure the SSD RAID drive is detected:
4) Create and format the partition using the Disk Management utility
and start using the SSD RAID drive.
6
Setting up the SSD7120 for a Linux Distribution
Please download the Linux Software Package from the HighPoint
Website: http://www.highpoint-tech.com/USA_new/series-ssd7120-
download.htm
Please follow the Linux Installation guide included with the software
package to install and setup the SSD7120 RAID controller.
Customer Support
If you encounter any problems while utilizing the SSD7120 RAID
controller, or have any questions about this or any other HighPoint
Technologies, Inc. product, feel free to contact our Customer Support
Department.
Web Support:
https://www.highpoint-tech.com/websupport/
HighPoint Technologies, Inc. websites:
https://www.highpoint-tech.com
© Copyright 2018 HighPoint Technologies, Inc. All rights reserved.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Highpoint SSD7120 Quick Installation Guide

Type
Quick Installation Guide

Highpoint SSD7120, a NVMe U.2 RAID controller, is compatible with PCIe 3.0 x16 slots and supports NVMe SSDs via SFF-8643 to U.2 cables or an NVMe backplane. It's well-suited for Windows 10, Windows Server 2012 R2 and 2016, and Linux distributions with Kernel 3.3 or later. This device empowers you with the ability to configure NVMe SSDs into RAID arrays for enhanced performance and data protection in your storage system.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI