Chore-Time MW2364A Nipple Pipe Installation guide

Brand
Chore-Time
Model
MW2364A Nipple Pipe
Type
Installation guide

Chore-Time MW2364A Nipple Pipe is a device designed to provide water to poultry in a controlled and efficient manner. It consists of a pipe assembly with nipples spaced along its length, allowing multiple birds to drink simultaneously. The pipe assembly can be easily installed and removed from the support channel, making it convenient for maintenance and cleaning. The nipples are designed to prevent water wastage and provide a consistent flow rate, ensuring that the birds have access to fresh water at all times.

Chore-Time MW2364A Nipple Pipe is a device designed to provide water to poultry in a controlled and efficient manner. It consists of a pipe assembly with nipples spaced along its length, allowing multiple birds to drink simultaneously. The pipe assembly can be easily installed and removed from the support channel, making it convenient for maintenance and cleaning. The nipples are designed to prevent water wastage and provide a consistent flow rate, ensuring that the birds have access to fresh water at all times.

Introduction
This instruction is to be used as a guide to install nipple pipe assemblies less channel. Removal of existing equipment
will be necessary prior to installation. The support channel from the existing equipment will be used for the new
equipment installation.
Installation of the new equipment will require two people to complete.
Before removal of existing equipment:
•Disconnect power to the anti-roost system (if installed).
•Turn off the water supply.
Remove Equipment:
1.Loosen the anti-roost system (if installed).
2.Remove channel bracket or keys from both ends of the pipe assemblies being replaced.
3.Slide the pipe assembly to be replaced out of the coupling liner assembly, slope compensator, or regulator
assembly.
4.Insert a flat head screw driver between the saddle and the
support channel as shown.
•Start with the saddle closest to the end of the pipe assembly.
5.Twist the screw driver and the saddle will release from the
support channel.
•The pipe assembly will not release completely from the
support channel until the last saddle has been released.
Be careful not to damage the support channel during removal
of the water pipe assembly!
6. Repeat steps 4. and 5. at the remaining saddle locations to
completely release the pipe assembly from the support
channel.
•The pipe assembly will fall out of the support channel once
the last saddle has been released in step 5.
Nipple Pipe Assembly Less Channel
Installation Guide
Figure 1. Separating the Water line
Figure 2. Release Saddle from Support Channel
Chore-Time Poultry Production Systems, a Division of CTB, Inc.
P.O. Box 2000 • Milford, Indiana 46542-2000 • U.S.A.
Phone (574) 658-4101 • Fax (877) 730-8825
E-Mail: poultry@choretime.com • Internet: www.choretimepoultry.com
MW2364 AFebruary 2010
Insert Screw Driver
Between Saddle and
Support Channel
Twist Screw Driver to
Release the Saddle
Nipple Pipe Assembly Less Channel
MW2364 A
2
Install Equipment:
1.Install one end of the pipe assembly into the coupling
liner assembly, slope compensator, or regulator
assembly.
2.Install pipe assembly to the support channel.
•One person should hold the pipe assembly up next to
the support channel while the other is installing the
saddle assemblies.
a.Rotate the pipe assembly to have one ear of the saddle
inside the support channel.
b.Begin installing at the first saddle from the end of the
pipe assembly installed in step 1.
c.Reach over the support channel and pull up on the
saddle assembly to snap the saddles into the support
channel.
d.Repeat for all saddles on the pipe assembly.
3.Install end of the pipe assembly into the coupling liner assembly, slop compensator, or regulator assembly.
4.Install channel bracket or keys to both ends of the pipe assemblies.
5.Tighten anti-roost system (if installed). The spring should be stretched to an overall length of 8" [203mm].
Adjust as required.
6.Turn on the anti-roost system (if installed).
7.Turn on the water supply.
Pull up on saddle
assembly
Figure 3. Installing Pipe Assembly
Support
Channel
One saddle ear out of
the support channel.
Figure 4. Securing the Water Line Together
  • Page 1 1
  • Page 2 2

Chore-Time MW2364A Nipple Pipe Installation guide

Brand
Chore-Time
Model
MW2364A Nipple Pipe
Type
Installation guide

Chore-Time MW2364A Nipple Pipe is a device designed to provide water to poultry in a controlled and efficient manner. It consists of a pipe assembly with nipples spaced along its length, allowing multiple birds to drink simultaneously. The pipe assembly can be easily installed and removed from the support channel, making it convenient for maintenance and cleaning. The nipples are designed to prevent water wastage and provide a consistent flow rate, ensuring that the birds have access to fresh water at all times.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents