4-075-727-21
--9
FD Trinitron
TM
Digital Reality Creation
Operating Instructions
KV-32XBR400 KV-36XBR400
WARNING
To reduce the risk of fire or shock hazard, do not expose the TV to
rain or moisture.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
RISQUE DE CHOC ELECTRIQUE,
NE PAS OUVRIR
PRECAUCION
RIESGO DE CHOQUE ELECTRICO
NO ABRIR
CAUTION: TO REDUCETHE RISK OF ELECTRICSHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the
presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
CAUTION
When using TV games, computers, and similar products with your
TV, keep the brightness and contrast functions at low settings. If a
fixed (non-moving) pattern is left on the screen for long periods of
time at a high brightness or contrast setting, the image can be
permanently imprinted onto the screen. Continuously watching
the same program can cause the imprint of station logos onto the
TV screen. These types of imprints are not covered by your
warranty because they are the result of misuse.
Note on Caption Vision
This television receiver provides display of television closed
captioning in accordance with §15.119 of the FCC rules.
Note on Cleaning the TV
Clean the TV with a soft dry cloth. Never use strong solvents such
as thinner or benzine, which might damage the finish of the
cabinet.
Note to CAW System Installer
This reminder is provided to call the CATV system installer's
attention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable ground
shall be connected to the grounding system of the building, as close
to the point of cable entry as practical.
Use of this television receiver for other than private viewing of
programs broadcast on UHF or VHF or transmitted by cable
companies for the use of the general public may require
authorization from the broadcaster/cable company and/or
program owner.
NOTIFICAIION
This equipment has been tested and found to comply with the
limits for a Class B digital device pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference with radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
J Reorient or relocate the receiving antennas.
"3 Increase the separation between the equipment and receiver.
J Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
_3 Consult the dealer or an experienced radio / TV technician for
help.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority
to operate this equipment.
Safety
Operate the TV only on 120 V AC.
The plug is designed, for safety purposes, to fit into the wall
outlet only one way. If you are unable to insert the plug fully
into the outlet, contact your dealer.
If any liquid or solid object should fall inside the cabinet,
unplug the TV immediately and have it checked by qualified
service personnel before operating it further.
Installing
J To prevent internal heat buildup, do not block the ventilation
openings.
_l Do not install the TV in a hot or humid place, or in a place
subject to excessive dust or mechanical vibration.
The AC power cord is attached to the rear of the TV with
hooks. Do not attempt to remove the cord from these hooks.
Doing so could cause damage to the TV.
As an ENERGYSTAR®Partner,
Sony has determined that this
product or product models meets
the ENERGYSTAR®guidelines
for energy efficiency.
ENERGYSTAR®is a U.S. registered mark.
CO) TruSurround
TruSurround is a trademark of SRS
Labs, Inc. SRS and the SRS symbol are
registered trademarks of SRS Labs, Inc.
in the United States and selected foreign
countries. SRS and TruSurround are
incorporated under license from SRS
Labs, Inc. and is protected under United
States Patent Nos. 4,748,669 and 4, 841, 572 with numerous
additional issued and pending foreign patents. Purchase of this
product does not convey the right to sell recordings made with the
TruSurround technology.
FD Trinitron and the Wega logo are trademarks of Sony
Corporation.
Owner's Record
The model and serial numbers are provided on the front of this
instruction manual and at the rear of the TV. Refer to them
whenever you call upon your Sony dealer regarding this product.
Important Safeguards
For your protection, please read these instructions completely, and
keep this manual for future reference.
Carefully observe and comply with all warnings, cautions and
instructions placed on the set, or described in the operating
instructions or service manual.
WARNING
To guard against injury, the following basic safety precautions
should be observed in the installation, use, and servicing of the set.
Use
Power Sources
This set should be operated only from the type
of power source indicated on the serial / model
plate. If you are not sure of the type of electrical
power supplied to your home, consult your
dealer or local power company. For those sets
designed to operate from battery power, refer
to the operating instructions.
Grounding or Polarization
This set is equipped wJt]l a polarized AC power cord plug (a plug
having one blade wider than the other), or with a three-wire
grounding type plug (a plug having a third pin for
grounding).Follow the instructions below:
For the set with a polarized AC power cord plug
This plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fit, contact your electrician to
have a suitable outlet installed. Do not defeat the safety purpose of
the polarized plug by fordng it in,
Alternate Warning
For the set with a three-wire grounding type AC plug
This plug will only fit into a grounding-type
power outlet. This is a safety feature. If you are .__Z_ L_,'_
unable to insert the plug into the outlet, contact
your electrician to have a suitable outlet installed.
Do not defeat the safety purpose of the grounding plug.
Overloading
Do not overload wall outlets, extension cords or
convenience receptacles beyond their capacity,
since this can result in fire or electric shock.
Always turn the set off when it is not to be
used. When the set is left unattended and
unused for long periods of time, unplug it
from the wall outlet as a precaution against
the possibility of an internal malfunction that
could create a fire hazard.
Object and Liquid Entry
Never push objects of any kind into the set
through the cabinet slots as they may touch
dangerous voltage points or short out parts that
could result in a fire or electric shock. Never spill
liquid of any kind on the set.
Attachments
Do not use attachments not recommended by the
manufacturer, as they may cause hazards.
Cleaning
Unplug the set from the wall outlet before
cleaning or polishing it. Do not use liquid
cleaners or aerosol cleaners.
Use a cloth lightly dampened with water for
cleaning the exterior of the set. If a snapping or
popping sound from a TV set is continuous or
frequent while the TV is operating, unplug the TV
and consult your dealer or service technician. It is
normal for some TV sets to make occasional
snapping or popping sounds, particularly when
being turned on or off.
Installation
Water and Moisture
Do not use power-line operated sets near
water -- for example, near a bathtub,
washbowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool, etc.
Accessories
Do not place the set on an unstable cart, stand,
table or shelf. The set may fall, causing serious
injury to a child or an adult, and serious damage
to the set. Use only a cart or stand recommended
by the manufacturer for the specific model of TV.
An appliance and cart combination should be
moved with care. Quick stops, excessive force,
and uneven surfaces may cause the appliance and
cart combination to overturn.
Ventilation
The slots and openings in the cabinet and in the
back or bottom are provided for necessary
_l i t"
ventilation. To ensure reliable operation of the set, and to protect it
from overheating, these slots and openings must never be blocked
or co_'ered.
El
L3
CI
Cl
Never cover the slots and openings with a
cloth or other materials.
Never block the slots and openings by
placing the set on a bed, sofa, rug or other
similar surface.
Never place the set in a confined space, such
as a bookcase, or built-in cabinet, unless
proper ventilation is provided.
Do not place the set near or over a radiator
or heat register, or where it is exposed to
direct sunlight.
Power-Cord Protection
Do not allow anything to rest on or roll over the
power cord, and do not place the set where the
power cord is subject to wear or abuse.
Antennas
Outdoor Antenna Grounding
If an outdoor antenna is installed, follow the precautions below. An
outdoor antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or
where it can come in contact with such power lines or circuits.
WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM,
EXTREME CARE SHOULD BE TAKEN TO KEEP FROM
CONTACTING SUCH POWER LINES OR CIRCUITS AS
CONTACT WITH THEM IS ALMOST INVARIABLY FATAL.Be
sure the antenna system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code (NEC) in USA and
Section 54 of the Canadian Electrical Code in Canada provides
information with respect to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
Antenna Grounding According to the NEC
Refer to section 54-300 of Canadian Electrical Code for Antenna
Grounding.
NEC:National Electrical Code
Antenna lead in wire
Antenna dischargeunit
(NECSection810 20)
Ground clamps
Antenna lead-in wire
Powerservicegrounding electrode
system(NECArt 250 PartH)
Lightning
For added protection for this television receiver during a lightning
storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna.
This will prevent damage to the receiver due to lightning and
power-line surges.
Service
Damage Requiring Service
Unplug the set from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
/ When the power cord or plug
is damaged or frayed.
_1 If liquid has been spilled into
the set.
J If the set has been exposed to
rain or water.
J
If the set has been subject to
excessive shock by being
dropped, or the cabinet has
been damaged.
If the set does not operate
normally when following the
operating instructions. Adjust
only those controls that are
specified in the operating
instructions. Improper
adjustment of other controls
may result in damage and
will often require extensive
work by a qualified technician
to restore the set to normal operation.
F_aY'r_ o_" "rAiJr
N
When the set exhibits a distinct change in performance -- this
indicates a need for service.
Servicing
Do not attempt to service the set yourself since
opening the cabinet may expose you to dangerous
voltage or other hazards. Refer all servicing to
qualified service personnel.
Replacement Parts
When replacement parts are required, be sure the service
technician certifies in writing that he has used replacement parts
specified by the manufacturer that have the same characteristics as
the original parts.
Unauthorized substitutions may result in fire, electric shock, or
other hazards.
Safety Check _.._=,o,
Upon completion of any service or repairs to the .-_--_x_
set, ask the service technician to perform routine
safety checks (as specified by the manufacturer) to
determine that the set is in safe operating
condition, and to so certify. When the set reaches
the end of its useful life, improper disposal could _,j
result in a picture tube implosion. Ask a qualified _•
service technician to dispose of the set.
Contents
Introducing the FD Trinitron VVega
Overview ................................................................ 1
Presenting the FD Trinitron Wega ...................... 2
Using the Remote Control ................................... 3
Installing the TV
Overview ................................................................ 5
Connecting a Cable or Antenna .......................... 6
Connecting a VCR and Cable .............................. 9
Connecting a VCR and Cable Box .................... 10
Connecting Two VCRs for Tape Editing ......... 11
Connecting a Satellite Receiver ......................... 12
Connecting a Satellite Receiver with a VCR ...13
Connecting an Audio Receiver ......................... 14
Connecting a DVD Player with Component
Video Connectors ........................................ 15
Connecting a DVD Player with A/V
Connectors ................................................... 16
Connecting a Digital TV Receiver .................... 17
Connecting a Camcorder ................................... 17
Using the CONTROL S Feature ........................ 18
Setting Up the TV Automatically ..................... 18
Using the Features
Overview .............................................................. ] 9
Using Favorite Channels .................................... 20
Using Twin View ................................................ 21
Using the Freeze Function ................................. 23
Using the Menus
Overview .............................................................. 25
Using the Video Menu ....................................... 26
Using the Audio Menu ...................................... 28
Using the Channel Menu ................................... 30
Using the Parent Menu ...................................... 31
Using the Timer Menu ....................................... 34
Using the Setup Menu ........................................ 35
Other Information
Overview .............................................................. 37
TV Controls and Connectors ............................. 38
Using the Remote Control ................................. 40
Troubleshooting .................................................. 46
Specifications ....................................................... 48
Index ..................................................................... 51
V
Overview
This chapter defines the contents of your Wega TV, and provides an
overview of how to set up and use basic features.
Topic Page
Presenting the FD Trinitron Wega 2
using the Remote control 3
Introducing the FD Trinitron Wega
Presenting the FD Trinitron Wega
The FD Trinitron Wega (pronounced VAY-GAH) is characterized by
outstanding contrast, uncompromising accuracy, and corner-to-
corner detail.
You'll recognize the superiority of Wega technology almost
immediately. The first thing you'll notice is minimal glare from the
flat picture tube. This flat-screen technology improves picture detail
without distortion, unlike conventional curved screens. The FD
Trinitron delivers outstanding image detail not only at the screen
center, but also at the corners -- so you can enjoy a bright, clear
picture from any location in a room.
Features Some of the features that you will enjoy with your new TV include:
DRC-MF (Digital Reality Creation, Multi Function): Unlike
conventional line doublers, the DRC feature doubles vertical and
horizontal lines, resulting in four times the density for quality
sources such as DVD, Satellite and Digital camcorder.
J Twin ViewTM: Using Multi-Image Driver (MIDX), Twin View
allows you to watch two programs side by side with the ability to
zoom in one picture. You can watch pictures from two different
sources (1080i, 480p and 480i) simultaneously.
J 16:9 Enhancement: Vertical Compression technology that
maximizes picture resolution on "anamorphic" or "enhanced for
widescreen" sources, including selected DVDs.
O Velocity Modulation: Vertical line enhancement that sharpens
picture definition.
o Steady Sound: Equalizes volume levels so there is consistent
output between programs and commercials.
21 Parental Control: V-Chip technology allows parents to block
unsuitable programming for younger viewers.
o Component Video Inputs: Offers the best video quality for DVD,
(480p, 480i) Digital Set-top box (HD1080i) connections.
2i S-VIDEO Inputs: Provides a high-quality image for connected
equipment.
E3 Favorite Channel Preview: Preview up to eight favorite channels
without leaving the current channel.
2
Introducing the FD Trinitron Wega
Using the Remote Control
Inserting Batteries Insert two size AA (R6) batteries (supplied) by matching the + and -
on the batteries to the diagram inside the battery compartment.
Removethe batteries to avoid damagefrom possible battery leakagewhenever you
anticipate that the remotecontrol will not be usedfor an extended period.
Handlethe remote control with care.Avoid dropping it, getting it wet, or placing it in
direct sunlight, neara heater,or where the humidity is high.
Remote Control
Overview
SLEEP DISPLAY
GUIDE
Q®®
®®®
®®®
FUNCTION--
W/VIDEO VC4_OVD SAT/CABLE IV
CD _ OCD
0 0
RESET AV 12 3 Ovo RM-Y174
SONY
[ TV
Here's an overview of the buttons on the remote control you will
probably use most often. For a complete description of the remote
control, see "Using the Remote Control" on page 40.
To Do This ... Use This Button
Turn the TV TV (POWER)
on and off
Select channels 0 - 9 and ENTER
directly Press 0 - 9 to select a channel, the channel changes
after 2 seconds. Press ENTERfor immediate selection.
Scan through CH +[-
channels
[] Toscan rapidlythrough the channels,pressand hold down
the CH+ or CH-button.
Adjust the volume VOL +l-
Switch video inputs TVNIDE0
(such as a VCR) Press repeatedly to toggle through all video inputs.
Display the Menu to MENU
make changes to the For details, see "Using the Menus" on page 25.
TV
View the Favorite FAVORITES
Channels list For details, see "Using Favorite Channels" on
page 20.
Using the on-screen _ ,,c_ _ ,._.
functions
Move
Select
3
Overview
This chapter includes illustrated instructions for setting up ),our TV:
Topic Page
Connecting a Cable Or Antenna 6
connecting a VCR and Cable
Connecting a vcR and cable Box 10
9
Connecting Two VCRs for Tape Editing 11
Connecting a Satellite Receiver 12
connecting a sateiiite Receiver With a VCR 13
Connecting an Audio Receiver 14
Connecting a DVD ]?layer with Component Video 15
Connectors
connecting a DVD piayer with Aiv co_ectors 16
Connecting a Digital TV Receiver 17
Using the CONTROL S Feature 18
setting up the TV Automaticaiiy ............................. 18
Note About the AC
Power Cord
The AC power cord is attached to the rear of the TV with hook. Use
caution when removing the AC plug from its holder. Gently slide the
plug in the upward direction to remove from hook. Once removed,
the AC power plug should automatically disengage from its stored
location.
AC Power cord
You can detach
the cord from
this hook
5
Installing the TV
Connecting a Cable or Antenna
Connecting Directly
to Cable or an
Antenna
The connection you choose depends on the cable found in your
home. Newer homes; are equipped with standard coaxial cable (see
[]); older homes probably have 300-ohm twin lead cable (see I'/1); still
other homes may contain both (see []).
[] VHFOnlyor VHF/UHF or Cable
75-ohm VHFIUHF
coaxial 3_])m _
cable
Rear of TV
[] VHF Only or UHF Only or VHF/UHF
300-ohm twin
lead cable VHFIUHF
I '(_ _ [_l _ Rear of TV
Antenna connector
[]
VHF and UHF
75-ohm
coaxial cable
_""I
_=__HFRear of TV
U/V Splitter
I :_ (not supplied)
300-ohm twin
lead cable
6
Installing the TV
Cable and Antenna
If your cable provider does not feature local channels, you may find
this set up convenient.
CATVcable
AUX
_),-,-,,,,i_ Rear ofTV
(No connection to (_
TO CONVERTER)
TO CONVERTER
Antenna cable
VHFIUHF
Select CABLE or antenna (ANT) mode by pressing ANT on the remote
control.
_:_ In order to receivechannelswith an antenna, you need to turn your Cableto OFFand
perform the Auto Programfunction (seepage 30).
Cable Box
Connections
Some pay cable TV systems use scrambled or encoded signals that
require a cable box to view all channels.
Cable Box
2
Connect the coaxial connector from your cable service to the
cable box's IN jack.
Using a coaxial cable, connect the cable box's OUT jack to the
TV's VHF / UHF jack.
Cable
| |
oo'
Cable box
VHFIUHF
Rear of TV
If you will be controlling all channel selectionthrough yourcable box, you should
consider usingthe ChannelFixfeature (seepage 30).
7
Installing the TV
CableBoxand Cable
For this set up, you can switch between scrambled channels (through
your cable box), and normal (CATV) channels by pressing ANTon the
remote control.
Cable box AUX
.earo Tv
OUT
TO CONVERTER
7S-ohm coaxial cable (not supplied)
, Signal
i
VHF/UHF
CAW cable (unscrambled channels)
_:_ YourSonyremote control can be programmed to operateyour cable box(see
"Programming the RemoteControl" on page 42).
When using FavoriteChannel orTwin View, you cannot view the AUX input in the
window picture.
PressingANT switches between these inputs.
If you areconnecting atcablebox through the AUX input and would like to switch
between the AUXand normal (CAW) input you shouldconsider usingthe Channel Fix
feature (seepage 30).
8
Installing the TV
Connecting a
VCR and Cable
1
2
Connect the cable TV cable to the VCR's IN jack.
Using a coaxial cable, connect the VCR's OUT jack to the TV's
VHF / UHF jack.
Using an A/V cable, connect the VCR's A/V OUT jacks to the
TV's A/V IN jacks.
_:a If your VCRhasan SVIDEOjack: Forbest picture quality, usean SVIDEOconnection
instead of the yellow video cableon your combined A/V cable. Usingan SVIDEOcable,
connectthe VCR'sS VIDEOOUTjack to the TV's SVIDEOINjack. S VIDEOdoesnot
provideaudio, soaudio cablesmust still be connectedto provide sound.
TV
AUDIO-R (red)
AUDIO-L (white)
VIDEO (yellow)
@
AUX
@
TO
CONVERTER
VHF/LIHF
AIV cable
Coaxial cable 2
'{_ VCR
! I !
/;
IN
Cable
9
Installing the TV
Connecting a
VCR and Cable Box
2
3
Connect the single (input) jack of the splitter to your incoming
cable connection, and connect the other two (output) jacks (using
coaxial cable) to IN on your cable box and VHF / UHF on your TV.
Using a coaxial cable, connect the cable box's OUT jack to the
VCR's VHF / UHF IN jack.
Using an A/V cable, connect the VCR's A/V OUT jacks to the
TV's A/V IN jacks.
If your VCRhasan SVIDEOjack: Forbest picture quality, usean SVIDEOconnection
instead of the yellow video cableon your combined AN cable. Using an SVIDEOcable,
connectthe VCR'sS'VIDEOOUTjackto the TV's SVIDEOINjack. SVIDEOdoes not
provide audio, so audio cables must still be connectedto provide sound.
AUDIO-R (red)
AUDIO-L (white)
VIDEO (yellow)
I
I
VCR
TV
I ' vloEo IN JMONITO
S VlOEO
Vl O
JAUOIO
_r
,v_,, - v
- p=
- p.
AUOlO
\
A/V cable
Coaxial
cable
1
Splitter
(not supplied)
10
Installing the TV
Connecting Two VCRs for Tape Editing
If you connect two VCRs, you can use the TV's MONITOR OUT
feature to perform tape-to-tape editing. In the connection shown
below, the TV functions as a monitor and sends the program being
played by the playback VCR to the recording VCR.
Connect the VCR intended for playback using the connection
instructions on page 10 of this manual.
2
Using A/V connectors, connect AUDIO and VIDEO IN on the
VCR intended for recording to MONITOR AUDIO and VIDEO
OUT on your TV.
Youcannot record signalsfrom equipment connectedto the Y,Ps,PRinput.
TV
@
^ux
@
TO
CONVERTER
@
VHF/UHF
A/V cable
VCR (recording)
............
,.
Toperform tape editing, set the TVto the video input intended for playbackby pressing
the TV/VlDEObutton on the remotecontrol.
11
Installing the TV
Connecting a Satellite Receiver
1 Connect the satellite antenna cable to the satellite receiver's
SATELLITE IN jack.
2 Using an A/V cable, connect the satellite receiver's A/V OUT
jacks to the TV's A/V IN jacks.
3 Connect a coaxial cable from your cable or antenna to the TV's
VHF / UHF jack.
If your satellite receiverhasan SVIDEOjack: Forbest picture quality, usean SVIDEO
connection instead of the yellow video cable on your combined AIV cable. Using an S
VIDEOcable,connect the satellite receiver'sVIDEOOUTjack to the TV's SVIDEOIN
jack. SVIDEOdoesnot provideaudio, soaudio cablesmust still be connectedto provide
sound.
TV
swoco
VIDEO
AUDIOR__
AUDIO-R (red) _;_
AUDIO-L (white) _
VIDEO (yellow)
- p_
c R
-_ - p_
)._ AUDIO VHF/UH_
-R
Coaxial
J cable
3
Satellite receiver
.... _'_1 1
o_,1_ ......... so _
,._ .... J_)_) I | Satellite
•r 1" 1" _ antenna
" " " cable
AIV cable
12
Installing the TV
Connecting
a Satellite Receiver with
a VCR
1 Connect the satellite antenna cable to the satellite receiver's
SATELLITE IN jack.
2 Connect the CATV cable to the VCR's VHF/UHF IN jack.
3 Using a coaxial cable, connect the VCR's OUT jack to the TV's
VHF / UHF jack.
4 Using an A/V cable, connect the satellite receiver's A/V OUT
jacks to the VCR',; A/V IN jacks.
5 Using an A/V cable, connect the VCR's A/V OUT jacks to the
TV's A/V IN jacks.
IV
sviol _
vl_E i FB
AUDI _10
AUDIO4 (white)
VIDEO (yellow)
A/V cable
O
AUX
@
TO
CONVERTER
VHrIU.F
Coaxial
cable
Coaxi_
cabl
I
Satellite receiver _ 1
l ....L
o_I@®®® I.....
VCR _4
Io r....
13
Installing the TV
Connecting an Audio Receiver
1 Using audio cables, connect the TV's AUDIO OUT jacks to the
audio receiver's audio LINE IN jacks.
TV
_uo,o-._0_-_
(red) _ (white)
I_1 input I_ t_ I_I
I_II=_o_olI_-_I
____HIL -i_
@
Au×
@
To
CONVeRtER
@
VHr/UHF
14
Installing the TV
Connecting a DVD
Video Connectors
Player with Component
Using three separate component video cables, connect the DVD
player's Y, PB, and PR jacks to the Y, PB, and PR jacks on the TV.
_:a TheY,PB,and PRjackson your DVDplayeraresometimeslabeled Y,CB,and CR,or
Y,B-Y,and R-Y.If so, connectthe cablesto likecolors.
TheY,PB,and PRjacks do not provideaudio, soaudio cablesmust beconnectedto
providesound.
2 Using an audio cable, connect the DVD player's audio OUT jacks
to the TV's audio IN jacks.
DVD player
2
Component video cables I_I_
i @
VIDEOIN M0mX( AUO
OUT OU AUX
CONVERTER
@
@ ®
Audio cable
AUDIO-R (red)i_
AUDIO-L (white) V
TV
@
VH_IUHF
15
Installing the TV
Connecting a DVD Player with A/V Connectors
_:u If your DVDplayer hasvideo component output connectors:for bestpicture quality use
the connectiondescribedon page 15.
2
Using audio cables, connect the DVD player's audio OUT jacks to
the TV's audio IN jacks.
Using an S VIDEO cable, connect the DVD player's S VIDEO jack
to the TV's S VIDEO jack.
TV
SVIDEO ,-._,
cable
DVD player
LINE OUT
2
Audio cable
L_8%J®
_ AUDIO-R (red)
AUDIO-L (white)
16
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
