CAME 62700030 Installation guide

Brand: CAME

Model: 62700030

Type: Installation guide

FA0 1 53 4- EN

VA/01

EN English

CAME S.p.A.

Via Martiri della Libertà, 15

31030 Dosson di Casier

Treviso - Italy

Tel. (+39) 0422 4940

Fax (+39) 0422 4941

[email protected] - www.

came.com

PRODUCT DATA AND INFORMATION

Description

62700030

VA/01 Power supply for X1 video-intercom systems 18 V DC - 1100 mA.

Description of parts

DL1 DL2

–

+12V

BIN1 BIN2 BIN3 BOUT

1 Power supply terminal block

2 Connector for serial cable RS232 (not used)

3 Mini USB port for programming from PC

4 Entry panel programming button

5 Jumper for storing and deleting codes and TAGs

6 AUX 1 Open Collector output (max. 100 mA)

7 Common inputs

8 AUX 2 Open Collector output (max. 100 mA)

9 Entry panel power supply unit (18 V DC)

The device is electronically protected against overloads and short

circuits.

10 BUS inputs from entry panels

11 Riser output

12 USB connection warning LED (green)

13 Programming status warning LED (yellow)

FA01534-EN - 02/2022

VA/01

Page 2 - FA01534-EN - 02/2022 - © CAME S.p.A.

Technical data

MODELS VA/01

Power supply (V AC) 220-230 AC 50/60 Hz

Maximum current draw (mA AC) 350 AC

Entry panels nominal power supply (V) 18 DC

Riser power supply (V) 20 DC

Modules (no.) 12 DIN EN50022 35 x 7.5

Entry panels peak current draw (A) 1.1<15s*

Entry panel current draw (mA) 600

Maximum dissipated power (W) 25

Average life (hours) 90000

Operating temperature (°C) 0 ÷ +35

Storage temperature (°C) -25 ÷ +70

Note *1.6 A<15s with riser not connected or

powered separately

(*) Before installing the product, keep it at room temperature where it has previously been

stored or transported at a very high or very low temperature.

(**) The average product life is a purely indicative estimate. It applies to compliant usage,

installation and maintenance conditions. It is also inﬂ uenced by other factors, such as climatic

and environmental conditions.

Size

43,5

7,5 57

210

106

Page 3 - FA01534-EN - 02/2022 - © CAME S.p.A.

INSTALLING

Install the power supply unit in a closed cabinet ONLY. Ensure there are ventilation grilles.

ALWAYS install the power supply unit horizontally.

Page 4 - FA01534-EN - 02/2022 - © CAME S.p.A.

INSTALLATION EXAMPLES WITH WIRING

Multi-family installation with 4 internal receivers

Use a VCM/1D cable. The distance between the power supply unit and the internal receiver must not exceed 100 m. The sum of all the sections must not exceed 1000 m.

–

OUT

XDV/304

–

+12V

BIN1 BIN2 BIN3 BOUT

DL2 DL1

–M1

VA/01

OPALEWIDE PEV/01

AGT V

AGT V BF

AGT V EVO

AGT V

AGT V BF

AGT V EVO

SW4

SW2SW3

SW0

Page 5 - FA01534-EN - 02/2022 - © CAME S.p.A.

Multi-family installation with 3 entry panels

Use a VCM/2D cable. Each section of cable, from power supply unit to entry panel, must not exceed 100 m. The sum of all sections of cable to the entry panels must not

exceed 300 m.

+12V

BIN1 BIN2 BIN3 BOUT

DL2 DL1

–M1

VA/01

12V

B OUT

VAS/100.30

12V

B OUT

12V

B OUT

XDV/304

Page 6 - FA01534-EN - 02/2022 - © CAME S.p.A.

Multi-family installation with 2 entry panels and 4 cameras

+12V

BIN1 BIN2 BIN3 BOUT

DL2 DL1

–M1

VA/01

12V

B OUT

12V

B OUT

XDV/304

VSC/01

V+

V–

–

V+

V–

–

V+

V–

–

V+

V–

–

Page 7 - FA01534-EN - 02/2022 - © CAME S.p.A.

CALCULATING ENTRY PANEL DRAW

Entry panel draw key

Entry panel Consumption (mA)

1 Entry panel when idle 130

2 Entry panel when idle 130

3 Entry panel when idle 35

4 Entry panel with video camera on 320

5 Entry panel with electric lock active 500

Examples with idle elements

VA/01

Examples with active elements

VA/01

Programming an intercommunicating group

You can download the PROGRAMMING LOG from the website docs.came.com by entering the code L20211011.

Program the intercommunicating group ONLY AFTER programming calls to each internal receiver.

DL1 DL2

–

Activation

Press and hold the 1 button for at least 25 seconds, until the LED 2 ﬂ ashes quickly.

Put the jumper 3 in the [+] position.

On the internal receiver, press the intercommunicating button you wish to use to call it.

You will hear a beep to signal that the internal receiver has been added to the

intercommunicating group.

You can change the internal receiver call button by repeating the activation

procedure.

Press the button 1 to end the procedure and position the jumper 3 in neutral.

Repeat the procedure for each internal receiver you want to add to the

intercommunicating group.

You can add up to 4 internal receivers per intercommunicating group.

The procedure ends automatically after 30 minutes of inactivity.

After adding an internal receiver to an intercommunicating group, it can no longer

be excluded from that group.

Deactivation

Press and hold the 1 button for at least 25 seconds, until the LED 2 ﬂ ashes quickly.

Put the jumper 3 in the [-] position.

Keep the jumper in this position for at least 20 seconds.

Press the button 1 to end the procedure and position the jumper 3 in neutral.

The VA/01 power supply unit allows for one intercommunicating group only.

To add more intercommunicating groups, install a VSE/301 selector for each intercommunicating group after the video distributor.

An intercommunicating group with VA/01 cannot coexist with other groups with VSE/301.

VA/01 VA/01

VSE/301

VSE/301 VSE/301

VA/01

XDV/304 XDV/304

XDV/304

General precautions

The product, in its original packaging supplied by the manufacturer must only be transported in a closed environment (railway carriage, containers, closed vehicles).

If the product malfunctions, stop using it and contact customer services at [email protected] or via the telephone number on the website.

The manufacture date is provided in the production batch printed on the product label. If necessary, contact us at https://www.came.com/global/en/contact-us.

The general conditions of sale are given in the o cial CAME price lists.

Dismantling and disposal

Dispose of the packaging and the device responsibly at the end of its life cycle, in compliance with the laws in force in the country where the product is used. The recyclable components

are marked with the material symbol and ID.

THE DATA AND INFORMATION IN THIS MANUAL MAY BE CHANGED AT ANY TIME AND WITHOUT NOTICE.

THE MEASUREMENTS, UNLESS OTHERWISE STATED, ARE IN MILLIMETRES.

Legislative references

This product complies with the applicable standards in force at the time of manufacturing.