Page is loading ...
ISSUED 05-2014
PACKAGE CONTENTS
1OF4
STYLE NUMBER: TST0092E
WARNING:
CAUTION:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching
off the circuit breaker or removing the fuse.
● These instructions are provided for your safety. It is very important that they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb(s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
● Do not touch the bulb with bare hands use a cloth or glove.
WARNINGS AND CAUTIONS
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 20 - 30 minutes
● (1) Medium Base 100W Maximum,Alternate (1) CFL bulb.
● : Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape,
safety glasses.
● 1-866-535-1869
● www.illuminadirect.com
Bulb Recommended:
Tools Required
Phone #:
E-mail:
website:
PREPARATION
www.illuminadirect.com
1-866-535-1869
UM-TST0092E
PART
DESCRIPTION
QUANTITY
A
Mounting Screw
2pcs
3pcs
4pcs
4pcs
4pcs
4pcs
1pc
Wire Connector
Tab
Glass Panel
Long Screw
Short Screw
Fixture Hood
B
C
D
E
F
G
H
A
B
D
E
C
G
F
1pc
Fixture Assembly
H
2OF4
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
UM-TST0092E
FINISH: IMPERIAL BRONZE
(1) 100W
Bulb
(Not Supplied)
Medium
Base
9”Sq.
6.5”Sq.
9”
14.5”
PART NUMBER REPLACEMENT PART DESCRIPTION
REQ.
NO.
1
G2707PA Glass Panel
4
1
3OF4
INSTALLATION INSTRUCTIONS
STYLE NUMBER: UM-TST0092E
STEP 1:
A. Put the smooth side of glass outwards. Slip Glass
Panels inside of the Slot in the bottom edge of the
Cage.
b. Place Tabs onto the top edge of the Cage and Glass
Panel. Line up holes on Tabs and mounting holes on
the top edge of the Cage. Using screwdriver, thread
Short Screws into mounting holes on the top edge of
the Cage. Hand-tighten until snug.
Slot
Cage
Glass Panel
Short Screw
Tab
STEP 2:
a. Install the correct bulb referring to fixture markings and/or labels for maximum wattage.
STEP 3:
a. Place the Fixture Hood onto the top end of the Cage.
Line up Mounting Holes in the bottom of the Fixture
Hood and Holes on the top edge of the Cage. Using
screwdriver, thread Long Screw into the Mounting
Holes in the bottom of the Fixture Hood. Hand-tighten
until snug.
Cage
Fixture Hood
Long Screw
Mounting Hole
Hole
4OF4
INSTALLATION INSTRUCTIONS
STYLE NUMBER: UM-TST0092E
STEP 4:
a. Carefully fit the Post Fitter over the end of the Post (not
supplied), making sure the Post Fitter is fully seated.
b. Mark the drill point for the (2) Mounting Screws, using
(2) Mounting Holes as reference. After marking hole
locations, remove Fixture from Post and drill 1/16” pilot
holes for screws.
c. Refer to Step 5 for wire connections.
d. Secure the Fixture to Post with (2) Mounting Screws.
Post Fitter
Post not supplied()
Mounting Screw
STEP 5:
a. Connect the House Ground Wire to the Fixture Ground
Wire.
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (White or Ribbed Side).
c. Connect the House Black (or Red) Wire to the Fixture
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the
Outlet Box.
WHITE OR RIBBED
BLACK (OR RED) WIRE
GROUND WIRE
WHITE OR RIBBED
BLACK OR SMOOTH
GROUND WIRE
FROM HOUSE
FROM HOUSE
FROM HOUSE
FROM FIXTURE
FROM FIXTURE
FROM FIXTURE
Use Wire Connectors to connect the wires.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
/
