Page is loading ...
ISSUED 10-2014
PACKAGE CONTENTS
1OF3
STYLE NUMBER: TST2944A
PART
DESCRIPTION
QUANTITY
A
B
C
D
1pc
1pc
1pc
1pc
WARNING:
CAUTION:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching
off the circuit breaker or removing the fuse.
● These instructions are provided for your safety. It is very important that they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb(s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
● Do not touch the bulb with bare hands use a cloth or glove.
WARNINGS AND CAUTIONS
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 10 - 15 minutes
● Bulb Recommended: (2) Medium Base 75W Maximum, Alternate bulb (2) CFL.
● No Tools Required for Assembly
● 1-866-535-1869
● www.illuminadirect.com
Phone #:
E-mail:
website:
PREPARATION
www.illuminadirect.com
1-866-535-1869
UM-TST2944A
E
1pc
F
1pc
B
Shade
A
Finial
Big Knurled Nut
Column
D
J
E
Check Ring
F
Small Knurled Nut
Nipple with Hex Nut
G
Spacer
H
I
Socket Assembly
Base
K
Lock Washer
L
Spring Washer
Flat Washer
M
C
Wingnut
N
G
1pc
H
1pc
I
1pc
J
1pc
K
1pc
L
1pc
M
1pc
N
1pc
2OF3
PART NUMBER
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
REQ.
NO.
1
UM-TST2944A
FINISH: Vintage Bronze
(2) 75W
Bulb
(Not Supplied)
Medium
Base
16” Dia.
8”
23”
7.5” Dia.
3OF3
INSTALLATION INSTRUCTIONS
STYLE NUMBER: UM-TST2944A
STEP 1:
A. Pass the Base, Lock Washer and Spring Washer
through the Nipple on the Column, secure by threading
Wingnut onto the Nipple. Hand tighten until sung.
B. Thread the Socket Assembly onto the Column, hand
tighten until sung.
STEP 2:
A. Thread the hex nut end of Nipple with Hex Nut into the
hex coupling, hand tighten until sung.
B. Place Spacer and Check Ring over the Nipple with Hex
Nut, secure by threading the Small Knurled Nut onto
the nipple. Hand tighten until sung.
C. Thread the Big Knurled Nut onto the Nipple, hand
tighten until snug.
D. Place the Flat Washer and the Shade over the Nipple.
Secure by threading the Finial onto the Nipple. Hand
tighten until snug.
Socket Assembly
Column
Base
Lock Washer
Spring Washer
Wingnut
Hex
Coupling
Finial
Shade
Flat Washer
Big Knurled Nut
Small Knurled Nut
Check Ring
Nipple with Hex Nut
Spacer
Bulb
STEP 3:
A. This fixture uses standard bulb with medium base .
Maximum 75 watts.
B. Insert bulb and screw snugly into place.
Your fixture is now assembled and ready to use. Enjoy!
/
