Honeywell TH1110DV1009 User manual

Category
Thermostats
Type
User manual
® U.S. Registered Trademark. Patents pending.
Copyright © 2013 Honeywell International Inc.
All rights reserved.
Installation
Guide
PRO TH2000DV/TH1000DV Series
Thermostats
This manual covers the following models
• TH1100DV:ForHeatonlysystems
• TH2110DV/TH1110DV:For1Heat/1Coolsystems
• TH2210DV/TH1210DV:For2Heat/1Coolheatpumpsystemsonly
(Pullthermostatfromwallplateandturnovertofindmodelnumber.)
System Types
TH2110DV/TH1110DV:
• Gas,oil,orelectricheatwithair
conditioning
• Warmair,hotwater,high-efficiency
furnaces,1Heat/1Coolheatpumps,
steam,gravity
• Heatonly
• Heatonlywithfan
• Coolonly
• 750mVheatingsystems
TH2210DV/TH1210DV:
• 2Heat/1Coolheatpumps
TH1100DV:
• Gas,oil,orelectricheat
• Warmair,hotwater,steam,gravity
• Heatonly
• 750mVheatingsystems
Must be installed by a trained, experienced technician
Readtheseinstructionscarefully.Failuretofollowtheseinstructions
candamagetheproductorcauseahazardouscondition.
Need Help?
Forassistancewiththisproductpleasevisithttp://customer.honeywell.com
orcallHoneywellCustomerCaretoll-freeat1-800-468-1502
69-2800EFS-01
Installation Guide
2
69-2800EFS—01
C IS OPTIONAL
WITH BATTERIES
NOT
USED
R
C
AUX/
E
Y
G
O
B
M34682
Wallplateinstallation
Removethewallplatefromthethermostat
asshownatleft,thenfollowdirections
belowformounting.
1. Pullwiresthroughwirehole.
2. Positionwallplateonwall,levelandmarkhole
positions with pencil.
3. Drillholesatmarkedpositionsasshownbelow,
thentapinsuppliedwallanchors.
4. Placewallplateoveranchors,insertandtighten
mountingscrews.
Pullatbottomtoremovethermostatfrom
wallplate.
CAUTION: ELECTRICAL HAZARD
Cancauseelectricalshockorequipmentdamage.Disconnectpowerbeforebeginning
installation.
Drill3/16"holesfordrywall.Drill7/32"holesforplaster.
MERCURY NOTICE
Ifthisproductisreplacingacontrolthatcontainsmercuryinasealedtube,donotplace
the old control in the trash. Contact the Thermostat Recycling Corporation at
www.thermostat-recycle.orgor800-238-8192forinformationonhowandwheretoproperly
andsafelydisposeofyouroldthermostat.
M34683
Wallanchors
Mountingscrews
Wirehole
PRO TH2000DV/TH1000DV Series
3
69-2800EFS—01
Power options
TH2110DV/TH1110DV:
B Changeovervalveenergizedinheating
O Changeovervalveenergizedincooling
G Fanrelay
Y Compressor contactor
W Heat relay
C 24Vaccommon.For2-transformer
systems,usecommonwirefrom
coolingtransformer.
R 24Vacpowerfromheatingtransformer
Rc 24Vacpowerfromcoolingtransformer
TH2210DV/TH1210DV:
B Changeovervalveenergizedin
heating
O Changeovervalveenergizedin
cooling
G Fanrelay
Y Compressor contactor
Aux/E Auxiliaryheatrelay
C 24Vaccommon
R 24Vacpower
TH1100DV:
W Heat relay
C 24Vaccommon
R 24Vacpower
Terminal designations
Wiring
M32808B
RWYG
B
RcO C
TH2110DV/
TH1110DV
CYGO
BR
Aux/
E
M32809B
TH2210DV/TH1210DV
Not
Used
M34673
INSERT BATTERIES FOR
PRIMARY OR BACKUP POWER
M34699
KEEP WIRES IN
THIS SHADED AREA
REMOVE FACTORY-INSTALLED JUMPER
ONLY FOR TWO-TRANSFORMER SYSTEMS
CONNECT C FOR PRIMARY
AC POWER (OPTIONAL IF
BATTERIES ARE INSTALLED)
RC
R
C
W
Y
G
O
B
TERMINAL
BLOCK SHOWN
M34800
RW C
TH1100DH
Installation Guide
4
69-2800EFS—01
Wiring
2H/1C Heat
Pump System
TH2210DV/TH1210DV
B Changeovervalveenergizedin
heating[5]
O Changeovervalveenergizedin
cooling[5]
G Fanrelay
Y Compressor contactor
Aux/E Auxiliaryheatrelay
C 24Vaccommon[3]
R Power[1]
1H/1C System
TH2110DV/
TH1110DV
(1 transformer)
G Fanrelay
Y Compressor contactor
W Heat relay
C 24Vaccommon[3]
R [R+Rcjoinedbyjumper]
Rc Power[1]
1H/1C System
TH2110DV/
TH1110DV
(2 transformers)
G Fanrelay
Y Compressor contactor
W Heat relay
C 24Vaccommon[3,4]
R Power(heatingtransformer)[1,2]
Rc Power(coolingtransformer)[1,2]
Heat Only System
TH1100DV
W Heat relay
C 24Vaccommon[3]
R Power[1]
1H/1C Heat
Pump System
TH2110DV/TH1110DV [7]
B Changeovervalveenergizedin
heating[5]
O Changeovervalveenergizedin
cooling[5]
G Fanrelay
Y Compressorcontactor[6]
W [W+Yjoinedbyjumper]
C 24Vaccommon[3]
R [R+Rcjoinedbyjumper]
Rc Power[1]
Heat Only
System
TH2110DV/TH1110DV
W Heat relay
C 24Vaccommon[3]
R [R+Rcjoinedbyjumper]
Rc Power[1]
Heat Only
System with
Fan TH2110DV/TH1110DV
G Fanrelay
W Heat relay
C 24Vaccommon[3]
R [R+Rcjoinedbyjumper]
Rc Power[1]
Cool Only
System
TH2110DV/TH1110DV
G Fanrelay
Y Compressor contactor
C 24Vaccommon[3]
R [R+Rcjoinedbyjumper]
Rc Power[1]
NOTES
Wirespecifications:
Use18-to22-gaugethermostatwire.
Shieldedcableisnotrequired.
[1] Powersupply.Providedisconnectmeansand
overloadprotectionasrequired.
[2] Removejumperfor2-transformersystems.
[3] Optional24Vaccommonconnection.
[4] Commonconnectionmustcomefromcool-
ingtransformer.
[5] UseeitherOorBterminalsforchangeover
valve.
[6] Useasmallpieceofwire(notsupplied)to
connectWandYterminals.
[7] SetfanoperationswitchtoHeat Pump
(seepage5).
Wiring guide — conventional and heat pump systems
CYGO
BR
Aux/
E
M32809B
TH2210DV/TH1210DV
Not
Used
RcCYW
GR
M32811
RcCYW
GR
M32812
RcCYWGO
BR
M32813
RcC
WR
M32814
RcCW
GR
M32815
RcCY
GR
M32816
See[notes]below
M34801
RW C
PRO TH2000DV/TH1000DV Series
5
69-2800EFS—01
M34679
Set
Cool
77
On
Fan
Auto
On
C IS OPTIONAL
WITH BATTERIES
NOT
USED
R
C
AUX/
E
Y
G
O
B
Fan
Auto
On
Off
Cool
Heat
Set
Hold
Run
E.M. Heat
M34676
Set
Cool
77
On
Fan
Auto
On
Off
Cool
Heat
C IS OPTIONAL
WITH BATTERIES
RC
R
C
W
Y
G
O
B
TH2110DV/TH1110DV only:
• Gas or Oil:Forgasoroilheating
systems,leavethefanoperation
switchinthisfactory-setposition.
(Thissettingisforsystemsthat
controlthefaninacallforheat.)
• Electric or Heat Pump:Change
theswitchtothissettingforheat
pumporelectricheatsystems.
(Thissettingisforsystemsthat
allow the thermostat to control the
faninacallforheat,ifafanwire
is connected to the Gterminal.)
Alignthethermostatwiththetabsonthe
wallplate,thenpushgentlyuntilthether-
mostat snaps in place.
Thermostatmounting
Setfanoperationswitch.
Pushexcesswire
backintothewall
opening.
Plugwallopening
withnon-flammable
insulation.
Fanoperationsettings
M34674
ELECTRIC
OR HEAT PUMP
GAS OR OIL
ELECTRIC
OR HEAT PUMP
GAS OR OIL
Installation Guide
6
69-2800EFS—01
5
5
M32819
Followtheprocedurebelowtoconfigurethethermostattomatchtheinstalled
heating/coolingsystem,andcustomizefeatureoperationasdesired.
Function
number
Setting
Tobegin,press and hold the s and tbuttonsuntilthedisplaychanges.
Press the s or tbuttontochangethesetting.
Press the s and tbuttonssimultaneouslyforonesecondto
advancetothenextfunction.
Press and hold the s and tbuttonstoexitandsavesettings.
Installersetup
M34680
Fan
Auto
On
Off
Cool
Heat
Set
Hold
Run
E.M. Heat
M34681
Set
Cool
77
On
Fan
Auto
On
Off
Cool
Heat
NOTE:Ifyoudonotpressanybuttonfor60secondswhileyouareinthe
setupmenu,thethermostatautomaticallysavesanychangesmadeand
exitsthemenu.
PRO TH2000DV/TH1000DV Series
7
69-2800EFS—01
Setup function Settings & options (factory default in bold)
5 Heating cycle rate
(CPH: cycles/hour)
TH2110DV, TH1110DV and
TH1100DV
5 For gas or oil furnaces of less than 90% efficiency
1 Forsteamorgravitysystems
3 Forhotwatersystems&furnacesofover90%efficiency
6 Forelectricfurnaces
[Othercyclerateoptions:2or4CPH]
6 Auxiliary heat
cycle rate (CPH)
TH2210DV and TH1210DV
3 For hot water systems & furnaces of over 90%
efficiency
1 Forsteamorgravitysystems
5 Forgasoroilfurnacesoflessthan90%efficiency
6 Forelectricfurnaces
[Othercyclerateoptions:2or4CPH]
9 Compressor
cycle rate (CPH)
3 Recommended for most compressors
[Othercyclerateoptions:1,2,4,5,or6CPH]
13 Early Start (TH2110DV
and TH2210DV)
1 On **See page 8
0 Off
14 Temperature
display
0 Fahrenheit
1 Celsius
15 Compressor
protection
1 Five-minute compressor off time (See page 8)
0 Nocompressorofftime
20 Clock display (TH2110DV
and TH2210DV)
0 12-hour display
1 24-hourdisplay
25 Lower temperature
range (TH1100DV only)
0 Standard range 40°F to 90°F (4.5°C to 32°C)
1 Lowerrange(forgaragemode)35°Fto90°F
(1.5°Cto32°C)
40 Restore program
schedule to default
(TH2110DV and
TH2210DV)
0 Off
1 On-programscheduledefaultsettingsarelistedinthe
operatingmanual
Installersetup
CAUTION: EQUIPMENT DAMAGE HAZARD
Compressorprotectionisbypassedduringtesting.Topreventequipmentdamage,avoid
cyclingthecompressorquickly.
NOTE: Theoptionsbelowmaynotbeavailableinallmodels.
Installation Guide
Automation and Control Solutions
Honeywell International Inc.
1985DouglasDriveNorth
GoldenValley,MN55422
http://customer.honeywell.com
® U.S. Registered Trademark
© 2013 Honeywell International Inc.
69-2800EFS—01M.S.05-13
Printed in U.S.A.
Early Start (SetupFunction13):Earlystartallowstheheatingorcoolingtoturnonbeforethe
programstarttime,sothetemperatureisreachedatthetimeyouset.
Compressor Protection(SetupFunction15):Forcesthecompressortowaitafewminutesbefore
restarting,topreventdamage.Duringthewaittime,themessageCoolOnorHeatOn(heatpumps
only)willflashonthedisplay.
Please contact your distributor to order replacement parts.
Cover plate assembly* ........................................ PartNumber50002883-001
*Usetocovermarksleftbyoldthermostats.
Temperature Ranges
• Heat:40°to90°F(4.5°to32°C)
• Cool:50°to99°F(10°to37°C)
Operating Ambient Temperature
• 32°to120°F(0°to48.9°C)
Shipping Temperature
• -20°to120°F(-28.9°to48.9°C)
Operating Relative Humidity
• 5%to90%(non-condensing)
Physical Dimensions
• 3-7/16”Hx4-10/16”Wx1-3/16”D
87mmHx119mmWx30mmD
Electrical Ratings
System Voltage(50/60Hz) RunningCurrent
Heat(1ststage) 20-30Vac 0.02-1.0A
(Powerpile) 750mVDC 100mADC
Auxiliaryheat 20-30Vac 0.02-1.0A
Cooling 20-30Vac 0.02-1.0A
Accessories&replacementparts
Specialfunctions
Specifications
3
69-2800EFS—01
Série PRO TH2000DV/TH1000DV
Optionsd’alimentation
TH2110DV/TH1110DV :
B Vanned’inversiondéclenchéeenmode
dechauffage
O Vanned’inversiondéclenchéeenmode
derefroidissement
G Relaisdeventilateur
Y Contacteurducompresseur
W Relaisdechauffage
C Commun24Vc.a.Danslessystèmes
àdeuxtransformateurs,utiliserle
filcommundutransformateurde
refroidissement.
R Alimentation24Vc.a.provenantdu
transformateurdechauffage
Rc Alimentation24Vc.a.provenantdu
transformateurderefroidissement
TH2210DV/TH1210DV :
B Vanned’inversiondéclenchéeen
modedechauffage
O Vanned’inversiondéclenchéeen
modederefroidissement
G Relaisdeventilateur
Y Contacteurducompresseur
Aux/E Relaisdesystèmedechauffage
auxiliaire
C Commun24Vc.a.
R Alimentation24Vc.a.
Désignation des bornes
Câblage
M32808B
RWYG
B
RcO C
TH2110DV/
TH1110DV
CYGO
BR
Aux/
E
M32809B
TH2210DV/TH1210DV
Non
utilisée
TH1100DV :
W Relaisdechauffage
C Commun24Vc.a.
R Alimentation24Vc.a.
MF34673
INSÉRER LES PILES POUR L’ALIMENTATION
PRIMAIRE OU DE SECOURS.
MF34699
GARDER LES FILS DANS
CETTE ZONE OMBRAGÉE
SEULEMENT SI LE SYSTÈME EST À DEUX
TRANSFORMATEURS
RACCORDER LA BORNE C
POUR L’ALIMENTATION
PRINCIPALE EN C.A. (OPTIONNEL
SI DES PILES SONT INSTALLÉES).
BORNIER
RC
R
C
W
Y
G
O
B
M34800
RW C
TH1100DH
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Honeywell TH1110DV1009 User manual

Category
Thermostats
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI