Honeywell th7000 User manual

Honeywell
Brand
Honeywell
Model
th7000
Category
Thermostats
Type
User manual
TH7000 Series
Touch-screen Programmable Thermostat
® U.S. Registered Trademark.
US Patents pending.
Copyright © 2011 Honeywell International Inc.
All rights reserved.
Installation
Guide
69-2668-03
System Types
• Gas,oil,orelectricheatwithair
conditioning
• Warmair,hotwater,highefficiency
furnaces,heatpumps,steam,
gravity
• Heatonly—two-wiresystems,
power to open and close
zonevalves(Series20),and
normallyopen zone valves
• Heatonlywithfan
• Coolonly
• 750mVheatingsystems
This manual covers the following models
• TH7220U:
For up to 2 Heat/1 Cool Heat Pumps or 2 Heat/2 Cool Conventional systems
(Pullthermostatfromwallplateandturnovertofindmodelnumber)
Need Help?
For assistance with this product please visit http://yourhome.honeywell.com
orcallHoneywellCustomerCaretoll-freeat1-800-468-1502
This thermostat contains a Lithium battery which may contain Perchlorate material.
PerchlorateMaterial—specialhandlingmayapply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate
Installation Guide
2
69-2668—03
MCR31514
M28073
Wallplate installation
1. Separatewallplatefromthermostat.
2. Mount wallplate as shown below.
MERCURY NOTICE
Ifthisproductisreplacingacontrolthatcontainsmercuryinasealedtube,donot
placetheoldcontrolinthetrash.Contactyourlocalwastemanagementauthorityfor
instructions regarding recycling and proper disposal.
Grasptopandbottomofwallplate
andpulltoremovefromthermostat.
CAUTION: ELECTRICAL HAZARD
Cancauseelectricalshockorequipmentdamage.Disconnectpowerbefore
beginning installation.
Drill3/16”holesfordrywall.
Drill7/32”holesforplaster.
Wallanchors
Wirehole Mounting screws
Must be installed by a trained, experienced technician
• Readtheseinstructionscarefully.Failuretofollowtheseinstructions
can damage the product or cause a hazardous condition.
TH7000 Series
3
69-2668—03
Conventional Terminal Letters:
R Heating power. Connect to secondary side
ofheatingsystemtransformer.
Rc Cooling power. Connect to secondary side
ofcoolingsystemtransformer.
C Commonwirefromsecondarysideof
coolingtransformer(if2transformers).
W 1st stage heat relay.
W2 2nd stage heat relay.
Y 1st stage compressor contactor.
Y2 2nd stage compressor contactor.
G Fan relay.
S1 Optional outdoor or remote sensor.
S2 Optional outdoor or remote sensor.
Heat Pump Terminal Letters:
R Heating power. Connect to secondary side
ofheatingsystemtransformer.
Rc Cooling power. Connect to secondary side
ofcoolingsystemtransformer.
C Commonwirefromsecondarysideof
coolingsystemtransformer.
Y 1st stage compressor contactor.
Aux Auxiliary heat relay.
G Fan relay.
E Emergency heat relay.
L Heat pump reset (powered continuously
when System is set to Em Heat; system
monitorwhensettoHeat,CoolorOff).
O/B Changeovervalveforheatpumps.
S1 Optional outdoor or remote sensor.
S2 Optional outdoor or remote sensor.
CONVENTIONAL
HEAT PUMP
C
G
Y
O/B
RC
R
AUX
E
L
S1
S2
C
G
Y
W
RC
R
W2
Y2
NOT
USED
S1
S2
MCR31515
M28420
For24VACprimarypower,connect
commonsideoftransformerto
“C” terminal.
Insertsuppliedbatteriesfor
primary or backup power.
Power options
Push excess wire back into the wall opening.
Plugwallopeningwithnon-flammableinsulation.
Removefactory-installedjumper
onlyfortwo-transformersystems.
Terminal Designations Shaded areas below apply only to TH7220.
Wiring
CONVENTIONAL
HEAT PUMP
C
G
Y
O/B
RC
R
AUX
E
L
S1
S2
C
G
Y
W
RC
R
W2
Y2
NOT
USED
S1
S2
SCREW
INSERT WIRES
THEN TIGHTEN SCREWS
WIRE HOLE
MCR31517
Installation Guide
4
69-2668—03
Wiring guide—conventional systems
Wiring
1H/1C System (1 transformer)
Rc Power [1]
R [R+Rcjoinedbyjumper]
W Heat relay
Y Compressor contactor
G Fan relay
C 24VACcommon[3]
S1 Optional outdoor/remote sensor
S2 Optional outdoor/remote sensor
Heat Only System
Rc Power [1]
R [R+Rcjoinedbyjumper]
W Heat relay
C 24VACcommon[3]
S1 Optional outdoor/remote sensor
S2 Optional outdoor/remote sensor
Heat Only System (Series 20)
Rc [R+Rcjoinedbyjumper]
R Series 20 valve terminal “R” [1]
W Series 20 valve terminal “B”
Y Series20valveterminal“W”
C 24VACcommon[3]
S1 Optional outdoor/remote sensor
S2 Optional outdoor/remote sensor
2H/2C System (1 transformer)
Y2 Cool relay 2
W2 Heat relay 2
Rc Power [1]
R [R+Rcjoinedbyjumper]
W Heat relay 1
Y Cool relay 1
G Fan relay
C 24VACcommon[3]
S1 Optional outdoor/remote sensor
S2 Optional outdoor/remote sensor
1H/1C System (2 transformers)
Rc Power(coolingtransformer)[1,2]
R Power(heatingtransformer)[1,2]
W Heat relay
Y Compressor contactor
G Fan relay
C 24VACcommon[3,4]
S1 Optional outdoor/remote sensor
S2 Optional outdoor/remote sensor
Heat Only System With Fan
Rc Power [1]
R [R+Rcjoinedbyjumper]
W Heat relay
G Fan relay
C 24VACcommon[3]
S1 Optional outdoor/remote sensor
S2 Optional outdoor/remote sensor
Cool Only System
Rc Power [1]
R [R+Rcjoinedbyjumper]
Y Compressor contactor
G Fan relay
C 24VACcommon[3]
S1 Optional outdoor/remote sensor
S2 Optional outdoor/remote sensor
2H/2C System (2 transformers)
Y2 Cool relay 2
W2 Heat relay 2
Rc Power(coolingtransformer)[1,2]
R Power(heatingtransformer)[1,2]
W Heat relay 1
Y Cool relay 1
G Fan relay
C 24VACcommon[3,4]
S1 Optional outdoor/remote sensor
S2 Optional outdoor/remote sensor
See [notes] below
[1] Power supply. Provide disconnect means and overload protection as required.
[2] Removejumperfor2-transformersystems.
[3] Optional24VACcommonconnection.
[4] Commonconnectionmustcomefromcoolingtransformer.
Shaded areas below apply only to TH7220.
TH7000 Series
5
69-2668—03
Shaded areas below apply only to TH7220.
Wiring guide—heat pump systems
Wiring
See [notes] below
[1] Power supply. Provide disconnect means and overload protection as required.
[3] Optional24VACcommonconnection.
[5] O/B set to control as either O or B in installer setup.
[6] IfLterminalisused,24VACcommon(terminalC)must be connected.
[7] Heat pump reset (powered continuously when thermostat is set to Em. Heat; system monitor when
settoHeat,Cool,orOff).
[8] InstallfieldjumperbetweenAux and Eterminalsifthereisnoemergencyheatrelay.
1H/1C Heat Pump (no auxiliary heat)
Rc Power [1]
R [R+Rcjoinedbyjumper]
O/B Changeover valve [5]
Y Compressor relay
G Fan relay
C 24VACcommon[3]
S1 Optional outdoor/remote sensor
S2 Optional outdoor/remote sensor
2H/1C Heat Pump (with auxiliary heat)
L Equipment monitor [6,7]
E Emergency heat relay [8]
Aux Auxiliary heat relay (Heat 2) [8]
Rc Power [1]
R [R+Rcjoinedbyjumper]
O/B Changeover valve [5]
Y Compressor relay
G Fan relay
C 24VACcommon[3]
S1 Optional outdoor/remote sensor
S2 Optional outdoor/remote sensor
M27518
M27519
Remove tab.
Alignpinsonbackofthermostatwith
slotsinwallplate,thenpushgentlyuntil
thermostat snaps into place.
Remove tab and mount thermostat
Installation Guide
6
69-2668—03
Done
M27521
10:10
20
0120
System & Fan
Schedule
Clock & More
M27522
Go Back
Next
Done
6
15
2012
MCR31518
Set date and time
Press st to set timePress st
tosetmonth,
then press NEXT
Repeat to set
year and then
dayofmonth
Installer setup
Press DONE to save changes.
Press DONE to save and exit.
1. Press SYSTEM & FAN.
2. Press and hold the SYSTEM
and DONE buttons until the
display changes.
3. Change settings as
required(seepages7-9).
System
Fan
Done
MCR31510
Press s/t to change setting
Press NEXT to advance to
nextfunction.
Press DONE to exit and
save changes.
20
0120
Go Back
Next
Done
MCR31511
TH7000 Series
7
69-2668—03
0120 Year
(rst two digits)
20 (2000-2099)
21 (2101-2178)
0130 Year
(second two digits)
12 (2012)
[Otheroptions:00-99]
0140 Month 6 [Otheroptions:1-12]
0150 Date 15 [Otheroptions:1-31]
0160 Schedule format 4 7-day programming
0 Non-programmable
0165 Restore energy saving
schedule
0 Continue using programmed schedule.
1 Restore thermostat program to energy saving settings.
0170 System type 1 1 heat/1 cool conventional
2 1 heat/1 cool heat pump (no aux. heat)
3 Heat only (2-wire systems)
4 Heatonlywithfan
5 HotwaterSeries20system(powertoopen&closezone
valves/normally open zone valves)
6 Cool only
7 2heat/1coolheatpump(withaux.heat)
8 2 heat/2 cool multistage conventional
9 2heat/1coolmultistageconventional
10 1 heat/2 cool multistage conventional
0180 Fan control
(heating)
0 Gas/Oil heat (equipment controls heating fan)
1 Electricfurnace(thermostatcontrolsheatingfan)
0190 Changeover valve
(O/B terminal)
0 O/B terminal controls valve in cooling
1 O/B terminal controls valve in heating
0200 Auxiliary heat 0 Electric backup heat
1 Fossilfuelbackupheat
0210 External fossil
fuel kit
1 External fossil fuel kit controls backup heat
0 Thermostat controls backup heat (outdoor sensor required)
0220 1st stage com-
pressor cycle rate
3 Recommended for most compressors
[Otheroptions:1,2,4,5or6CPH]
0230 2nd stage com-
pressor cycle rate
3 Recommended for most compressors
[Otheroptions:1,2,4,5or6CPH]
Setup functions Settings & Options (factorydefaultinbold)
Shaded areas below apply only to TH7220.
Continued on next page
Installation Guide
8
69-2668—03
0240 First stage heat
cycle rate (CPH=
cycles per hour)
5 Gas or oil furnaces of less than 90% efciency
1 Steam or gravity systems
3 Hotwatersystems&furnacesof90%+efciency
9 Electricfurnaces
[Otheroptions:2,4,6,7,8,10,11,12CPH]
0250 Second stage heat
cycle rate (CPH)
5 Gas or oil furnaces of less than 90% efciency
1 Steam or gravity systems
3 Hotwatersystems&furnacesof90%+efciency
9 Electricfurnaces
[Otheroptions:2,4,6,7,8,10,11,12CPH]
0270 Emergency heat
cycle rate (CPH)
9 Electric emergency heat
1 Steam or gravity systems
3 Hotwatersystems&furnacesof90%+efciency
5 Gasoroilfurnacesoflessthan90%efciency
[Otheroptions:2,4,6,7,8,10,11,12CPH]
0280 Backlight 0 Backlight on for approx. 8 seconds after keypress
1 Backlightalwaysonlowintensity,fullbrightafterkeypress
(requires24VACconnection)
0300 Manual/Auto
changeover
0 Manual changeover (Heat/Cool/Off)
1 Automaticchangeover(Heat/Cool/Auto/Off)
0310 Auto changeover
deadband
3 Heat/cool temperature 3 °F apart (1.5 °C) ** See page 11
[Otheroptions:2-9(2°Fto9°F/1°Cto5°C)]
0320 Temperature
display
0 Fahrenheit
1 Celsius
0330 Daylight savings 2 Auto-change to daylight savings time(2007andbeyond,
forareasthatusethenew2007DSTcalendar)
1 Auto-changetodaylightsavingstime(through2006,andfor
areas that do notusethenew2007DSTcalendar)
0 Daylightsavingstimeisturnedoff
0340 Remote sensor 0 No remote sensor
1 Outdoor sensor (display only)
2 Outdoor control sensor (select heat pumps) ** See page 11
3 Indoor sensor
0350 Heat pump
compressor lockout
0 No heat pump compressor lockout
Otheroptions:
5,10,15,20,25,30,35,40,45,50,55,60°F
(-15°Cto15.5°C)
0360 Heat pump
auxiliary lockout
0 No heat pump auxiliary lockout
Otheroptions:
5,10,15,20,25,30,35,40,45,50,55,60,65°F
(-15°Cto18.5°C)
Setup functions Settings & Options (factorydefaultinbold)
Shaded areas below apply only to TH7220.
Installer setup
Continued on next page
TH7000 Series
9
69-2668—03
Setup functions Settings & Options (factorydefaultinbold)
0500 Furnace lter
change reminder
0 Off
1 10-day run time (about 1 month)
2 30-day run time (about 3 months)
3 60-day run time (about 6 months)
4 90-dayruntime(about9months)
5 120-dayruntime(about1year)
6 365-dayruntime(about3years)
0510 Humidier pad
change reminder
0 Off
1 90calendardays
2 180 calendar days
3 365calendardays
0520 UV lamp change
reminder
0 Off
1 365calendardays
0530 Adaptive Intelligent
Recovery™
1 On ** See page 11
0 Off
0540 Program periods 4 4 program periods (Wake, Leave, Return, Sleep)
2 2programperiods(Wake,Sleep)
0580 Compressor
protection
5 5 minute compressor off time ** See page 11
[Otheroptions:0,1,2,3or4-minuteofftime]
0600 Heat temperature
range stop
90 Max. heat temperature setting is 90°F (32°C)
[Otheroptions:40-89°F(4°Cto32°C)]
0610 Cool temperature
range stop
50 Min. cool temperature setting is 50°F (10°C)
[Otheroptions:51-99°F(11°Cto37°C)]
0640 Clock format 12 12-hour time (i.e., “3:30 pm”)
24 24-hourtime(i.e.,“15:30”)
0650 Extended fan
timer (heat)
0 Off
90 Fanrunsfor90secondsaftercallforheatends
0660 Extended fan
timer (cool)
0 Off
90 Fanrunsfor90secondsaftercallforcoolingends
0670 Keypad lock 0 Keypad unlocked (fully functional)
1 Partially locked (access to temperature settings only)
2 Fully locked
0680 Heat temperature
control
2 Standard temperature control (recommended)
1 Chooseifroomiswarmerthansettemperature
3 Chooseifroomdoesnotreachsettemperature
0690 Cool temperature
control
2 Standard temperature control (recommended)
1 Chooseifroomiscoolerthansettemperature
3 Chooseifroomdoesnotreachsettemperature
0700 Temperature
display offset
0 Thermostat displays actual room temperature
[Otheroptions:-3,-2,-1,1,2,3°Foffset(-1.5°Cto1.5°C)
0710
RESET
0 No reset
1 Resetinstalleroptions&programscheduletofactorydefault
(only date and time settings are retained)
Installer setup
Installation Guide
10
69-2668—03
EEEE
0
1 es
Go Back Next Done
MCR31520
Onceyouenterinstallersetup,presstheGo Back button repeatedly until “Test” 1 appears.
Test number System status
Press st to
change status
Press Next to select next test.
Press DONE to exit testing.
Shaded areas below apply only to TH7220.
System test System status
CAUTION: EQUIPMENT DAMAGE HAZARD. Compressor protection is bypassed
duringtesting.Topreventequipmentdamage,avoidcyclingthecompressorquickly.
Installer system test
1 Cooling system 0 Compressorandfanturnoff
1 Compressorandfanturnon
2 Second stage compressor turns on
2 Fan system 0 Fanturnsoff
1 Fan turns on
3 Heating system 0 Heatandfanturnoff
1 Heatturnson(fanonifFunction0170issetforheatpump,
orifFunction0180issetto“1”)** See page 6
2 Second stage heat turns on
4 Emergency
heating system
0 Heatandfanturnoff
1 Heatandfanturnon
2 Second stage heat turns on (Auxiliary heat)]
20
0120
Go Back
Next
Done
MCR31511
TH7000 Series
11
69-2668—03
Auto Changeover(SetupFunction0300):WhensettoAuto,thethermostatautomaticallyselectsheating
orcoolingdependingontheindoortemperature.Heatandcoolsettingsmustbeatleast2degreesapart.If
function0380issettoOn,theheatandcoolsettingsmustbeatleast5degreesapart.
Remote Sensor(SetupFunction0340):Ifanoptionaloutdoorsensorisinstalled,thethermostatcan
displaytheoutsidetemperature.Ifanoptionalremoteindoorsensorisinstalled,thethermostatwilldisplay
the temperature at the sensor location (the internal sensor in the thermostat is not used).
Adaptive Intelligent Recovery(SetupFunction0530):Allowsthethermostatto“learn”howlongthe
furnaceandairconditionertaketoreachprogrammedtemperaturesettings,sothetemperatureisreached
at the scheduled time.
Compressor Protection(SetupFunction0580):Forcesthecompressortowaitafewminutesbefore
restarting,topreventdamage.Duringthistime,themessage“Wait”ashesonthedisplay.
Heat Pump Temperature Lockout (with fossil-fuelbackup):Ifthethermostatisinstalledwithanoptional
outdoorsensor,youcanselectacompressorlockouttemperature(Function0350).Whentheoutdoortem-
peratureisbelowthelockouttemperature,onlytheauxiliaryheatoperates.Whentheoutdoortemperature
isabovethelockouttemperature,onlythecompressoroperates.
Heat Pump Temperature Lockouts (with electric heatbackup):Ifthethermostatisinstalledwithan
optionaloutdoorsensor,youcanselectacompressorlockouttemperature(Function0350)and/oranaux-
iliaryheatlockouttemperature(Function0360).Whentheoutdoortemperatureisbelowthecompressor
lockouttemperature,onlytheauxiliaryheatoperates.Whentheoutdoortemperatureisabovetheauxiliary
lockouttemperature,onlythecompressoroperates.Iftheoutdoortemperatureisbetweenthecompressor
andauxiliarylockouttemperatures,boththecompressorandauxiliaryheatcanoperate.
Shaded areas below apply only to TH7220.
Special functions
Please contact your distributor to order replacement parts.
Outdoor temperature sensor ................................. PartNumberC7089U1006
Remote indoor temperature sensor ...................... PartNumberC7189U1005
Cover plate* ............................................................. PartNumber50002883-001
*(Usetocovermarksleftbyoldthermostats.)
Accessories & replacement parts
Installation Guide
Honeywell International Inc.
1985DouglasDriveNorth
GoldenValley,MN55422
http://customer.honeywell.com
Automation and Control Solutions
® U.S. Registered Trademark.
US Patents pending.
© 2011 Honeywell International Inc.
69-2668—03M.S.10-11
Printed in U.S.A.
Temperature Ranges
• Heat:40°to90°F(4.5°to32°C)
• Cool:50°to99°F(10°to37°C)
Operating Ambient Temperature
• 0°to120°F(-18°to48.9°C)
Shipping Temperature
• -30°to150°F(-34°to66°C)
Operating Relative Humidity
• 5%to90%(non-condensing)
Physical Dimensions
• 3-3/4”Hx6”Wx1-3/8”D
• 99mmHx152mmWx35mmD
Electrical Ratings
Terminal Voltage(50/60Hz) RunningCurrent
WHeating 20-30Vac 0.02-1.0A
(Powerpile) 750mVDC 100mADC
W2Heating 20-30Vac 0.02-0.6A
YCooling 20-30Vac 0.02-1.0A
Y2Cooling 20-30Vac 0.02-0.6 A
AuxAuxiliaryheat 20-30Vac 0.02-1.0A
O/BChangeover 20-30Vac 0.02-0.6A
LHeatpumpreset 20-30Vac 0.02-0.6A
Specifications
Need Help?
For assistance with this product please visit http://yourhome.honeywell.com
orcallHoneywellCustomerCaretoll-freeat1-800-468-1502
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Honeywell th7000 User manual

Honeywell
Brand
Honeywell
Model
th7000
Category
Thermostats
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents