sonnax T35-125-400-KIT Operating instructions

T35-125-400-KIT

Brand: sonnax

Model: T35-125-400-KIT

Type: Operating instructions

The sonnax T35-125-400-KIT is a versatile driveline component designed to enhance the performance of your vehicle's drivetrain. Specifically crafted for use with 1350 U-joints and 4-inch diameter tubing with a 0.125-inch wall thickness, this kit provides a reliable solution for various driveline applications.

The sonnax T35-125-400-KIT is a versatile driveline component designed to enhance the performance of your vehicle's drivetrain. Specifically crafted for use with 1350 U-joints and 4-inch diameter tubing with a 0.125-inch wall thickness, this kit provides a reliable solution for various driveline applications.

Splined Stub

& Sleeve Kit

Part No.

T35-125-400-KIT

• Yoke/Stub Shaft

• Splined Sleeve

• Boot

• Boot Clamps (2)

NOTE: For use with .125" wall thickness

aluminum tubing.

1. Install slip spline assembly into mating driveshaft tube.

2. Measure runout of assembled shaft, adjust if necessary and weld in accordance with standard

build procedures.

3. Balance shaft in accordance with standard build procedures.

4. Separate yoke shaft from splined sleeve.

5. Apply a light, even coating of grease to yoke shaft splines. e following greases are recommended:

• TriboGel® PA6110LCS synthetic grease

• Chevron® Ultra-Duty EP-2 grease (NLGI Grade 2)

• Spicer® 232799 Ultra-Duty EPS Multi-Purpose grease

6. Reinstall yoke shaft in splined sleeve, along with the protective boot included with the kit,

taking care to ensure the phasing witness marks on yoke shaft and sleeve are aligned (Figure 1).

Fits 1350 U-Joint, 4" Dia. Tubing

Figure 1

4.05"

4.91"

11.66"

Recommended Driveshaft Initial Setup Dimension (Mid-Stroke)

Yoke shaft and splined sleeve

phasing witness marks must be aligned as shown.

Splined

Sleeve

Yoke

Shaft

Yoke/Stub Shaft

Splined Sleeve

Boot

Boot

Clamps

©2023 Sonnax Transmission Company, Inc. • A Marmon / Berkshire Hathaway Company T35-125-400-KIT-IN 04-21-23

800-843-2600 • 802-463-9722 • F: 802-463-4059 • www.sonnax.com Page 1

Instructions

HIGH PERFORMANCE DRIVELINE PARTS

PERFORMANCE

7. Recommended installation setup length and

minimum/maximum operating lengths:

a. e recommended installation setup length

(mid-stroke) is 4.05" (Figure 1).

b. The recommended minimum collapsed

operating length is 3.30" (Figure 2).

c. e recommended maximum extended

operating length is 4.80" (Figure 3).

Figure 2

Recommended Minimum

Collapsed Length

3.30"

Figure 3

Recommended Maximum

Extended Length

4.80"

©2023 Sonnax Transmission Company, Inc. • A Marmon / Berkshire Hathaway Company T35-125-400-KIT-IN 04-21-23

800-843-2600 • 802-463-9722 • F: 802-463-4059 • www.sonnax.com Page 2

Instructions

HIGH PERFORMANCE DRIVELINE PARTS

PERFORMANCE

SPLINED STUB & SLEEVE KIT T35-125-400-KIT

1
2

sonnax T35-125-400-KIT Operating instructions

T35-125-400-KIT

Brand: sonnax

Model: T35-125-400-KIT

Type: Operating instructions

The sonnax T35-125-400-KIT is a versatile driveline component designed to enhance the performance of your vehicle's drivetrain. Specifically crafted for use with 1350 U-joints and 4-inch diameter tubing with a 0.125-inch wall thickness, this kit provides a reliable solution for various driveline applications.

Download PDF

Related papers

Other documents