KUZCO PD87172 User manual

Type
User manual

KUZCO PD87172 is an LED pendant light with a pre-wired LED module. It offers adjustable height and the ability to fine-tune wire length for a customized installation. Compatible with ELV (Electronic Low Voltage) or TRIAC type dimmers, it allows for precise light control. The fixture comes with all necessary hardware for easy installation.

KUZCO PD87172 is an LED pendant light with a pre-wired LED module. It offers adjustable height and the ability to fine-tune wire length for a customized installation. Compatible with ELV (Electronic Low Voltage) or TRIAC type dimmers, it allows for precise light control. The fixture comes with all necessary hardware for easy installation.

19054 28th Avenue Surrey, BC Canada V3Z 6M3
T: 604 538 7162 TF: 1-855 85 KUZCO F: 604 538 7196
W: kuzcolighting.com
INSTALLATION SHEET
PD87172
Ceiling LED Pendant
START FROM HERE
• Make sure POWER is COMPLETELY OFF at the fuse box
• Have your fixture installed by a qualified licensed electrician
• Prepare everything in a clear area
• Wear gloves at all time during this installation
• Read instructions carefully before you start assembly
• Keep this installation sheet for future reference
Technical Support: 1-855-855-8926
Please Note:
• This Kuzco LED fixture comes with pre-wired LED module(s)
• Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary
contact with the module could cause permanent damage
• Use ELV (Electronic Low Voltage) or TRIAC type of dimmer for dimming application
• 120V input
Page 1 of 2
1. Remove fixture from its original package
2. Separate mounting plate (1c) from canopy (2a) by
removing canopy screws (2b)
3. Attach mounting plate (1c) to electrical junction box (1a)
using junction box screws provided (1e) in hardware
package
4. Secure mounting plate (1c) to mounting surface with
anchors (1f) and screws (1g)
5. To change fixture height, push and hold wire gripper
(2g), slide wire to desired length and then release wire
gripper (2g) to secure
6. Make proper electrical connections (black to hot “L”,
white to neutral “N”, ground to “GND”) with wire nuts
(1b) provided in hardware package
7. Attach canopy (2a) to mounting plate (1c) with canopy
screws (2b)
8. Fine tone wire length if necessary, by push and hold
wire gripper (2g) and then adjust wire to desired length
20220322
1a.
1b.
1f.
1g.
1c.
1e.
2g.
2b.
2a.
19054 28th Avenue Surrey, BC Canada V3Z 6M3
FOR ALTERNATIVE SIDE CANOPY INSTALL
T: 604 538 7162 TF: 1-855 85 KUZCO F: 604 538 7196
W: kuzcolighting.com
INSTALLATION SHEET
PD87172
Ceiling LED Pendant
Note: Ideal distance of wire
grippers from canopy is
52-11/16” and 60-13/16”
START FROM HERE
• Make sure POWER is COMPLETELY OFF at the fuse box
• Have your fixture installed by a qualified licensed electrician
• Prepare everything in a clear area
• Wear gloves at all time during this installation
• Read instructions carefully before you start assembly
• Keep this installation sheet for future reference
Technical Support: 1-855-855-8926
60-13/16”
52-11/16”
Please Note:
• This Kuzco LED fixture comes with pre-wired LED module(s)
• Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary
contact with the module could cause permanent damage
• Use ELV (Electronic Low Voltage) or TRIAC type of dimmer for dimming application
• 120V input
Page 2 of 2
Illustration 1 Illustration 2
1. Disconnect output wires on drivers (4a)
2. Separate wire gripper (2g) from canopy (2a) by removing
nut and tooth washer (6a). Separate plug (6b) from canopy
(2a) by removing nut, tooth washer and flat washer (6c)
(See Illustration 1)
3. Feed fixture wires through centre hole on canopy plate
(7a), canopy (2a), tooth washer and nut (5a). Attach
canopy plate (7a) to canopy (2a), followed by wire gripper
(2g) and secure with tooth washer and nut (5a) (See
Illustration 2)
4. Make proper electrical connections between LED and DC
driver, LED- Negative, LED+ Positive using wago connector
(4b) provided (See Illustration 3 and refer to diagram on
driver)
5. Make proper electrical connections (black to hot “L”,
white to neutral “N”, ground to “GND”) with wire nuts
(1b) provided in hardware package
6. Attach canopy (2a) to mounting plate (1c) with canopy
screws (2b). Position desired amount of wire by
pushing gripper (2g) on canopy
7. Pull wire through aircraft barrel (3b) and stopper (3d).
Secure aircraft barrel (3b) to mounting surface with anchor
(3c) and screw (3a). Adjust wire to desired length and
secure with set screw (3e). Insert wire gripper (2g) into
aircraft barrel (3b) to close
8. Fine tone wire length if necessary, by push and hold
wire gripper (2g) and then adjust wire to desired length
6c.
7a.
6a.
Ground
Wire
2g.
2g.
6b.
2a.
5a.
2a.
Gruond
Wire
20220322
1a.
1b.
1c.
3c.
3b.
3d.
3e.
3a.
2g.
7a.
2a.
1e.
4a.
4b.
2b.
2g.
DC
Driver
A
LN
Illustration 3
Low Voltage
+
+
DC
Driver
B
LN
-
-
  • Page 1 1
  • Page 2 2

KUZCO PD87172 User manual

Type
User manual

KUZCO PD87172 is an LED pendant light with a pre-wired LED module. It offers adjustable height and the ability to fine-tune wire length for a customized installation. Compatible with ELV (Electronic Low Voltage) or TRIAC type dimmers, it allows for precise light control. The fixture comes with all necessary hardware for easy installation.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI