KUZCO PD87718 User manual

Type
User manual

KUZCO PD87718 is a versatile LED pendant light designed for modern and stylish interiors. With its adjustable height feature, you can customize the length of the wire to suit your specific needs. Whether you want to create a dramatic focal point or provide ambient lighting, this fixture offers the flexibility to achieve your desired look. The use of ELV (Electronic Low Voltage) or TRIAC dimmers allows for precise control over the brightness, setting the perfect mood for any occasion. Installation is made simple with pre-wired LED modules and clear instructions provided.

KUZCO PD87718 is a versatile LED pendant light designed for modern and stylish interiors. With its adjustable height feature, you can customize the length of the wire to suit your specific needs. Whether you want to create a dramatic focal point or provide ambient lighting, this fixture offers the flexibility to achieve your desired look. The use of ELV (Electronic Low Voltage) or TRIAC dimmers allows for precise control over the brightness, setting the perfect mood for any occasion. Installation is made simple with pre-wired LED modules and clear instructions provided.

19054 28th Avenue Surrey, BC Canada V3Z 6M3
T: 604 538 7162 TF: 1-855 85 KUZCO F: 604 538 7196
W: kuzcolighting.com
INSTALLATION SHEET
PD87718
Ceiling LED Pendant
1a.
1b.
1c.
1e.
1. Remove fixture from its original package
2. Separate mounting plate (1c) from canopy (2a) by
removing canopy screws (2b)
3. Attach mounting plate (1c) to electrical junction box (1a)
using junction box screws provided (1e) in hardware
package
4. Secure mounting plate (1c) to mounting surface with
anchors (1f) and screws (1g)
5. To change fixture height, push and hold wire gripper
(2g), slide wire to desired length and then release wire
gripper (2g) to secure
6. Make proper electrical connections (black to hot “L”,
white to neutral “N”, ground to “GND”) with wire nuts
(1b) provided in hardware package
7. Attach canopy (2a) to mounting plate (1c) with canopy
screws (2b)
8. Fine tone wire length if necessary, by push and hold
wire gripper (2g) and then adjust wire to desired length
2g.
2b.
2a.
START FROM HERE
• Make sure POWER is COMPLETELY OFF at the fuse box
• Have your fixture installed by a qualified licensed electrician
• Prepare everything in a clear area
• Wear gloves at all time during this installation
• Read instructions carefully before you start assembly
• Keep this installation sheet for future reference
Technical Support: 1-855-855-8926
Please Note:
• This Kuzco LED fixture comes with pre-wired LED module(s)
• Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary
contact with the module could cause permanent damage
• Use ELV (Electronic Low Voltage) or TRIAC type of dimmer for dimming application
• 120V input
Page 1 of 2
1f.
1g.
20220520
19054 28th Avenue Surrey, BC Canada V3Z 6M3
Illustration 1 Illustration 2
FOR ALTERNATIVE SIDE CANOPY INSTALL
T: 604 538 7162 TF: 1-855 85 KUZCO F: 604 538 7196
W: kuzcolighting.com
INSTALLATION SHEET
PD87718
Ceiling LED Pendant
1. Disconnect output wires on driver (4a)
2. Separate wire gripper (2g) from canopy (2a) by removing
nut and tooth washer (6a). Separate plug (6b) from canopy
(2a) by removing nut, tooth washer and flat washer (6c)
(See Illustration 1)
3. Feed fixture wires through centre hole on canopy plate
(7a), canopy (2a), tooth washer and nut (5a). Attach
canopy plate (7a) to canopy (2a), followed by wire gripper
(2g) and secure with tooth washer and nut (5a) (See
Illustration 2)
4. Make proper electrical connections between LED and DC
driver, LED- Negative, LED+ Positive using wago connector
(4b) provided (See Illustration 3 and refer to diagram on
driver)
5. Make proper electrical connections (black to hot “L”,
white to neutral “N”, ground to “GND”) with wire nuts
(1b) provided in hardware package
6. Attach canopy (2a) to mounting plate (1c) with canopy
screws (2b). Position desired amount of wire by
pushing gripper (2g) on canopy
7. Pull wire through aircraft barrel (3b) and stopper (3d).
Secure aircraft barrel (3b) to mounting surface with anchor
(3c) and screw (3a). Adjust wire to desired length and
secure with set screw (3e). Insert wire gripper (2g) into
aircraft barrel (3b) to close
8. Fine tone wire length if necessary, by push and hold
wire gripper (2g) and then adjust wire to desired length
1a.
1b.
1c.
6c.
7a.
6a.
Ground
Wire
2g.
2g.
6b.
2a.
3c.
3b.
3d.
3e.
3a.
2g.
7a.
2a.
1e.
4a.
4b.
2b.
5a.
Note: Ideal distance of wire
grippers from canopy is 12-13/16”
and 14-13/16”
2a.
Ground
Wire
14-13/16”
12-13/16”
START FROM HERE
• Make sure POWER is COMPLETELY OFF at the fuse box
• Have your fixture installed by a qualified licensed electrician
• Prepare everything in a clear area
• Wear gloves at all time during this installation
• Read instructions carefully before you start assembly
• Keep this installation sheet for future reference
Technical Support: 1-855-855-8926
2g.
DC
Driver
LN
-
+
Illustration 3
Low Voltage
Please Note:
• This Kuzco LED fixture comes with pre-wired LED module(s)
• Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary
contact with the module could cause permanent damage
• Use ELV (Electronic Low Voltage) or TRIAC type of dimmer for dimming application
• 120V input
Page 2 of 220220520
  • Page 1 1
  • Page 2 2

KUZCO PD87718 User manual

Type
User manual

KUZCO PD87718 is a versatile LED pendant light designed for modern and stylish interiors. With its adjustable height feature, you can customize the length of the wire to suit your specific needs. Whether you want to create a dramatic focal point or provide ambient lighting, this fixture offers the flexibility to achieve your desired look. The use of ELV (Electronic Low Voltage) or TRIAC dimmers allows for precise control over the brightness, setting the perfect mood for any occasion. Installation is made simple with pre-wired LED modules and clear instructions provided.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI