© 2017
www.classicexhibits.com
Order #XXXXX TF-512 General Layout
Plan View 10’
10’
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
© 2017
www.classicexhibits.com
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2017
www.classicexhibits.com Case 1 of 2
Order #XXXXX Case 1 Packing
© 2017
www.classicexhibits.com Case 2 of 2
Order #XXXXX Case 2 Packing
Shelf Supports
Shelf 5, 5A
5, 5A
4 3 2 1
Counter
Infills
6,7 6A,7A
Lit. Racks
Setup Hardware
Top View of Each Level
Level 1 Level 2 Level 3 Level 4 Level 5
© 2017
www.classicexhibits.com
Order #XXXXX
1
1A
3
4
4A
3A
8
7
7
6
6
6
6
5
5
2
2A
When assembled
Item
1/1A
2/2A
3/3A
4/4A
5
6
7
Qty.
1/1
1/1
1/1
1/1
2
4
2
Description
Base Plate
47.5”h Vertical Extrusion
47.5”h Vertical Extrusion
26”w Horizontal Extrusion
37”h Vertical Extrusion
12”w Horizontal Extrusion
12”w Horizontal Extrusion
Steps:
1) Attach base plates [1] & [1A] to lower verticals [2] & [3].
2) Attach upper verticals [2A] & [3A] to lower verticals [2] & [3].
3) Connect lower and upper horizontals [4] & [4A] between verticals.
4) Attach Graphics to the back side of the backwall.
5) Connect horizontals [6] & [7] between verticals [5] and backwall.
6) Attach horizontal [8] to front of upper verticals [2A] & [3A].
BACK SIDE
Velcro: Top
Edge
Velcro: Bottom
Edge
Velcro: Inside
Edge
Velcro: Inside
Edge
Velcro
PR37
Extrusion
Profile
Screws
Connector
Piece
S44 Connector
Silde extrusion over
connector and rest on
lower vertical;
secure with screws.
**To prevent product loss,
Keep all screws attached
to connector piece after
disassembling
Monitor Mount Plate Attachment
Attach mounting plate
to verticals as shown.
*
2A
1) Screw Aero Mount
to base plate.
2) Slide Aero Frame
over mount.
Canopy Attachment
to Base Plate
*
*
Backwall Assembly
© 2017
www.classicexhibits.com Step 1 of 3
Order #XXXXX Backwall Attachments
Header
Counter
Shelf
Shelf
When assembled
Steps:
1) Place shelves on lower horizontals.
2) Connect counter to front verticals and upper horiozntals.
3) Attach monitor mount to monitor mount plate as shown.
4) Attach header to upper verticals where indicated.
Velcro
Velcro
Monitor Mount Attachment
Then attach
wall plate to plate
using bolts and wing nuts
*
*
Attach standoff barrels to counter
and secure in place. Secure upper
shelf to standoffs using screw caps.
Upper Shelf to Counter Attachment
Upper Shelf -
Clear Plex
Threaded hole
in counter top
Standoff
Barrel
Screw
Cap
© 2017
www.classicexhibits.com Step 2 of 3
Order #XXXXX
Item
1
Qty.
1
Description
Base Plate
Steps:
1) Assemble aero frame in numerical order as shown.
2) Attach Graphic to aero frame.
3) Attach aero frame to base plate as shown in detail.
Note: aero key slide used for vertical aero.
4) Attach Light to top of aero frame.
Aero Frame
Canopy
Mount
Base Plate
Bolt
1) Screw Aero Mount to base plate.
2) Slide Aero Frame over mount.
Canopy Attachment
to Base Plate
*
Aero Key Slide
Slide top and bottom
key into the
groove of the
vertical extrusion.
*
*
*
Light Connection
Attach lights to
backwall where
desired and
tighten in place.
*
1
2
3
1
4
5
678
9
10
*
*
Aero Frame Assembly
Connections are made by holding the button
down and sliding the red tube into opposing
tube until the connection is made. To disassemble
push button and pull or twist extrusions apart.
Push-Button
Push-Button
66
6
6
Numbered Label
Using Your Setup Instructions
The Aero Overhead Sign Setup Instructions are created specically for your conguration. They include an
exploded view of the frame which is sequentially numbered. We encourage you to study the instructions
before attempting to assemble your exhibit.
Connections are kept very simple: no tools. Everything assembles with push-button
connectors and pre-connected horizontal sections.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
© 2017
www.classicexhibits.com Step 3 of 3
Order #XXXXX Pedestal Assembly
Infill
Infill
Infill
1
56
5
Door
Shelf Supports
Shelf Supports
Shelf Supports
Shelf Supports
Shelf
Counter
7
2
3
5A 6A
5A
7A
4
HingeHinge
When assembled
Item
1
2
3
4
5/5A
6/6A
7/7A
Qty.
1
1
1
1
2/2
1/1
1/1
Description
37.5”h Vertical Extrusion
37.5”h Vertical Extrusion
37.5”h Vertical Extrusion
37.5”h Vertical Extrusion
13.25”w Horizontal Extrusion
22.5”w Horizontal Extrusion
22.5”w Horizontal Extrusion
Steps:
1) Connect lower horizotnals [5], [6] & [7] between verticals [1-4].
2) Place infill between infills between verticals [1-4].
3) Attach door using Door Attachment detail.
4) Place shelf on shelf supports.
5) Attach upper horizontals [5A], [6A] & [7A] between verticals [1-4].
6) Attach iPad clam shell to counter using bolt under counter.
7) Place counter and iPad clam shell to lower assembly as shown.
BACK SIDE
BACK SIDE
FRONT SIDE
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Attachment
Hex
Nuts
Clam Shell rotates
between portrait
and landscape
viewing modes.
Swivel
Mounting
Plate
Swivel iPad Clamshell
Attachment
Bolt iPad clamshell to mounting
plate with hex nuts.
Wire
Access
iPad
Lock
Lock
*
*
/