Gigabyte MP72-HB0 User manual

MP72-HB0

Ampere® Altra® or Altra® Max ARM Server Motherboard

User Manual

Rev. 1.0

Copyright

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specifications and features in this manual may be made by GIGABYTE

without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or

published in any form or by any means without GIGABYTE's prior written permission.

Documentation Classications

In order to assist in the use of this product, GIGABYTE provides the following types of documentation:

 UserManual:detailedinformation&stepsabouttheinstallation,congurationandusethis

product (e.g. motherboard, server barebones), covering hardware and BIOS.



User Guide: detailed information about the installation & use of an add-on hardware or

  softwarecomponent(e.g.BMCrmware,rail-kit)compatiblewiththisproduct.

 Quick Installation Guide: a short guide with visual diagrams that you can reference easily for

installation purposes of this product (e.g. motherboard, server barebones).

Please see the support section of the online product page to check the current availability of these

documents

For More Information

Forrelatedproductspecications,thelatestrmwareandsoftware,andotherinformation,pleasevisit

our website at: http://www.gigabyte.com.

For GIGABYTE distributors and resellers, additional sales & marketing materials are available from our

reseller portal: http://reseller.b2b.gigabyte.com

For further technical assistance, please contact your GIGABYTE representative or visit

http://esupport.gigabyte.com/ to create a new support ticket.

For any general sales or marketing enquires, you may message GIGABYTE server directly by

email: server[email protected].

- 3 -

Table of Contents

MP72-HB0 Motherboard Layout ...................................................................................... 5

Block Diagram .................................................................................................................7

Chapter 1 Hardware Installation .....................................................................................8

1-1 Installation Precautions .................................................................................... 8

1-2 ProductSpecications ...................................................................................... 9

1-3 Installing and Removing the CPU .................................................................. 12

1-4 Installing and Removing Memory ................................................................... 14

1-4-1 8-ChannelMemoryConguration ..........................................................................14

1-4-2 Installing and Removing the Memory Module .......................................................15

1-4-3 DIMM Population Table ..........................................................................................15

1-4-4 AltraPlatformDDR4SuggestCongurationTable .................................................16

1-5 Installing and Removing the M.2 SSD Module ............................................... 17

1-6 Back Panel Connectors .................................................................................. 18

1-7 Internal Connectors ........................................................................................ 19

1-8 Jumper Settings ............................................................................................. 26

Chapter 2 BIOS Setup ..................................................................................................27

2-1 The Main Menu .............................................................................................. 29

2-2 Advanced Menu ............................................................................................. 32

2-2-1 Trusted Computing .................................................................................................33

2-2-2 ACPI Settings .........................................................................................................34

2-2-3 APEIConguration .................................................................................................35

2-2-4 General Watchdog Timer ........................................................................................36

2-2-5 X86EmulationConguration ..................................................................................37

2-2-6 PCI Subsystem Settings .........................................................................................38

2-2-7 InfoReportConguration .......................................................................................44

2-2-8 USBConguration ..................................................................................................45

2-2-9 NetworkStackConguration ..................................................................................46

2-2-10 IPConguration ......................................................................................................47

2-2-11 NVMeConguration ...............................................................................................48

2-2-12 SATAConguration.................................................................................................49

2-2-13 GraphicOutputConguration .................................................................................50

2-2-14 PowerRestoreConguration .................................................................................51

2-2-15 Broadcom NetXtreme-E 2Px10GBASE-T OCP 3.0 Ethernet .................................52

2-2-16 MACIPv4NetworkConguration ...........................................................................58

2-2-17 MACIPv6NetworkConguration ...........................................................................59

2-2-18 Driver Health ...........................................................................................................60

- 4 -

2-3 Chipset Setup Menu ....................................................................................... 61

2-3-1 CPUConguration ..................................................................................................62

2-3-2 RASConguration ..................................................................................................64

2-3-3 Memory Slot Information ........................................................................................65

2-3-4 Serialport console ...................................................................................................67

2-3-5 PCIERootComplexConguration .........................................................................68

2-4 Server Management Menu ............................................................................. 69

2-4-1 System Event Log ..................................................................................................70

2-4-2 Bmc self test log .....................................................................................................71

2-4-3 View FRU Information ............................................................................................72

2-4-4 BMCNetworkConguration ...................................................................................73

2-5 Security Menu ................................................................................................ 74

2-5-1 Secure Boot ...........................................................................................................75

2-6 Boot Menu ...................................................................................................... 78

2-7 Save & Exit Menu ........................................................................................... 80

2-8 BIOS POST Beep code (AMI standard) ......................................................... 82

2-8-1 PEI Beep Codes .....................................................................................................82

2-8-2 DXE Beep Codes ...................................................................................................82

- 5 -

MP72-HB0 Motherboard Layout

CPU0

CPU1

DIMM_P0_H0

DIMM_P0_G0

DIMM_P0_F0

DIMM_P0_E0

DIMM_P0_A0

DIMM_P0_B0

DIMM_P0_C0

DIMM_P0_D0

DIMM_P1_L0

DIMM_P1_K0

DIMM_P1_J0

DIMM_P1_I0

DIMM_P1_M0

DIMM_P1_N0

DIMM_P1_O0

DIMM_P1_P0

12 3 4 5 6

7

8

9

10

11

131415

12

16

17

18

19

20

21

25

22

23

24

26 27 28

29

31

30

32

- 6 -

Item Code Description

1 VGA1 VGA Port

2 SW_ID1 ID Button with LED

3 LAN2 10GbE LAN Port #2

4 LAN1 10GbE LAN Port #1

5 USB3_MLAN1 Server Management LAN Port (Top)/ USB3.0 Ports (Bottom)

6 DEBUG PORT Debug Port

7 ATX1 2 x 12 Pin Main Power Connector

8 PMBUS1 PMBus Connector

9 P12V_1 2 x 4 Pin 12V Power Connector (for CPU0)

10 P12V_2 2 x 4 Pin 12V Power Connector (for CPU1)

11 CPU0_FAN CPU0 Fan Connector

12 BAT1 Battery Socket

13 SATA1 Slimline Connector (SATAIII 6Gb/s Signal)

14 SATA3 SATAIII 6Gb/s Connector #3

15 SATA2 SATAIII 6Gb/s Connector #2

16 F_USB2 Front Panel USB 3.0 Connector

17 CPU1_FAN CPU1 Fan Connector

18 SYS_FAN1 System Fan Connector #1

19 SYS_FAN0 System Fan Connector #0

20 F_USB1 USB 2.0 Header

21 FP_1 Front Panel Header

22 BP_1 HDD Back Plane Board Connector

23 IPMB1 IPMB Connector

24 CON1 TPM Connector

25 PCIE_1 PCIe x16 Slot #1 (Gen4 x8)

26 PCIE_2 PCIe x16 Slot #2 (Gen4 x16)

27 PCIE_3 PCIe x16 Slot #3 (Gen4 x16)

28 NVME_2 Slimline SAS 4i Connector (NVMe/PCIe Gen4 x4)

29 NVME_1 Slimline SAS 4i Connector (NVMe/PCIe Gen4 x4)

30 PCIE_4 PCIe x16 Slot #4 (Gen4 x16)

31 P0_M2_SK1 M.2 slot (PCIe Gen4 x4, Support NGFF-2280/22110)

32 LED_BMC1 BMC Firmware Readiness LED

- 7 -

Block Diagram

- 8 - Hardware Installation

1-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can

become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read

the user's manual and follow these procedures:

• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

• Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

• When connecting hardware components to the internal connectors on the motherboard,

make sure they are connected tightly and securely.

• When handling the motherboard, avoid touching any metal leads or connectors.

• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

components such as a motherboard, CPU or memory. If you do not have an ESD wrist

strap,keepyourhandsdryandrsttouchametalobjecttoeliminatestaticelectricity.

•

Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

• Before unplugging the power supply cable from the motherboard, make sure the power

supply has been turned off.

• Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

• Before using the product, please verify that all cables and power connectors of your

hardware components are connected.

• To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

• Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

• Do not place the computer system on an uneven surface

.

• Do not place the computer system in a high-temperature environment.

• Turning on the computer power during the installation process can lead to damage to

system components as well as physical harm to the user.

• If you are uncertain about any installation steps or have a problem related to the use of the

product,pleaseconsultacertiedcomputertechnician.

Chapter 1 Hardware Installation

Hardware Installation - 9 -

1-2 Product Specications

Socket

Security

Security Server Operating Properties

Power Supply

Form Factor E-ATX

305W x 330D (mm)

Socket

Security

Security Server Operating Properties

Power Supply

CPU Ampere® Altra® or Altra® Max Processor

Dual processors, 7nm technology, LGA4926

Up to 128-core per processor, TDP 250W

NOTE:

If only 1 CPU is installed, some PCIe or memory functions might be unavailable

Socket

Security

Security Server Operating Properties

Power Supply

Chipset System on Chip

Socket

Security

Security Server Operating Properties

Power Supply

Memory 16 x DIMM slots

DDR4 memory supported only

8-Channel memory architecture

RDIMM modules up to 256GB supported

Up to 4TB of memory capacity supported per processor

Memory speed: Up to 3200 MHz

NOTE:Onlysupportscongurationswith1,2,4,6,8DIMMs(1DPC)

Socket

Security

Security Server Operating Properties

Power Supply

LAN 2 x 10Gb/s BASE-T LAN ports (Broadcom® BCM57416)

1 x 10/100/1000 management LAN

Socket

Security

Security Server Operating Properties

Power Supply

Onboard

Graphics

Integrated in Aspeed® AST2600

2D Video Graphic Adapter with PCIe bus interface

1920x1200@60Hz 32bpp, DDR4 SDRAM

Socket

Security

Security Server Operating Properties

Power Supply

Storage Interface 2 x 7-pin SATA 6Gb/s ports

1 x SlimSAS with 4 x SATA 6Gb/s ports

Socket

Security

Security Server Operating Properties

Power Supply

Expansion Slots Slot_4: 1 x PCIe x16 (Gen4 x16 bus) slot, from CPU_0

Slot_3: 1 x PCIe x16 (Gen4 x16 bus) slot, from CPU_0

Slot_2: 1 x PCIe x16 (Gen4 x16 bus) slot, from CPU_1

Slot_1: 1 x PCIe x16 (Gen4 x8 bus) slot, from CPU_0

2 x NVMe ports:

- SlimSAS 4i type

- PCIe Gen4 x4 per port

1 x M.2 slot:

- M-key

- PCIe Gen4 x4 per slot

- Supports NGFF-22110/2280 cards

- From CPU_0

NOTE:

We reserve the right to make any changes to the product specications and product-related

information without prior notice.

- 10 - Hardware Installation

Socket

Security

Security Server Operating Properties

Power Supply

Internal I/O

Connectors

1 x 24-pin ATX main power connector

2 x 8-pin ATX 12V power connectors

2 x SlimSAS connectors

1 x SlimSAS vertical connector

2 x 7-pin SATA connectors

1 x M.2 slots

1 x HDD back plane board header

2 x CPU fan headers

2 x System fan headers

1 x USB 3.2 Gen1 header

1 x USB 2.0 Gen1 header

1 x TPM header

1 x Front panel header

1 x PMBus connector

1 x IPMB connector

1xClearCMOSjumper

1xBIOSrecoveryjumper

1 x Case open header

Socket

Security

Security Server Operating Properties

Power Supply

Rear I/O

Connectors

2 x USB 3.2 Gen1

1 x VGA

1 x Debug port

2 x RJ45

1 x MLAN

1 x ID button with LED

Socket

Security

Security Server Operating Properties

Power Supply

TPM 1 x TPM header with SPI interface

Optional TPM2.0 kit: CTM010

- 11 - Hardware Installation

Socket

Security

Security Server Operating Properties

Power Supply

Board

Management

Aspeed® AST2600 management controller

GIGABYTE Management Console (AMI MegaRAC SP-X) web interface

Dashboard

HTML5 KVM

Sensor Monitor (Voltage, RPM, Temperature, CPU Status …etc.)

Sensor Reading History Data

FRU Information

SEL Log in Linear Storage / Circular Storage Policy

Hardware Inventory

FanProle

System Firewall

Power Consumption

Power Control

LDAP / AD / RADIUS Support

Backup&RestoreConguration

Remote BIOS/BMC/CPLD Update

Event Log Filter

User Management

Media Redirection Settings

PAM Order Settings

SSL Settings

SMTP Settings

Socket

Security

Security Server Operating Properties

Power Supply

Operating

Properties

Operating temperature: 10°C to 40°C

Operating humidity: 8-80% (non-condensing)

Non-operating temperature: -40°C to 60°C

Non-operating humidity: 20%-95% (non-condensing)

Hardware Installation - 12 -

1-3 Installing and Removing the CPU

Follow these instructions to Install the CPU:

1. Loosen the three captive screws in sequential order (1g2g3g4g5) securing the CPU cover.

2. Flip open the CPU cover.

3. Install the CPU into place in the CPU socket.

4. Flip the CPU cover into place over the CPU socket.

5 Tighten the CPU cover screws in sequential order (1g2g3g4g5) to secure the CPU cover in place.

6. Lower and place the fan-sink onto the top of the CPU socket. Then tighten the scews in sequential

order (1g2g3g4).

7. To remove the CPUs, follow steps 1-5 in reverse order.

Read the following guidelines before you begin to install the CPU:

• Make sure that the motherboard supports the CPU.

• Always turn off the computer and unplug the power cord from the power outlet before installing

the CPU to prevent hardware damage.

• Unplug all cables from the power outlets.

• Disconnect all telecommunication cables from their ports.

• Placethesystemunitonaatandstablesurface.

• Open the system according to the instructions.

WARNING!

Failure to properly turn off the server before you start installing components may cause serious

damage. Do not attempt the procedures described in the following sections unless you are a

qualiedservicetechnician.

1

3

4

5

2

345

5

3

2

1

4

- 13 - Hardware Installation

12

4

3

6

- 14 - Hardware Installation

1-4 Installing and Removing Memory

Read the following guidelines before you begin to install the memory:

• Make sure that the motherboard supports the memory. It is recommended that memory of the

same capacity, brand, speed, and chips be used.

• Always turn off the computer and unplug the power cord from the power outlet before installing

the memory to prevent hardware damage.

• Memory modules have a foolproof design. A memory module can be installed in only one

direction. If you are unable to insert the memory, switch the direction.

1-4-1 8-Channel Memory Conguration

This motherboard provides 16 DDR4 memory slots and supports 8-Channel Technology. After the memory

isinstalled,theBIOSwillautomaticallydetectthespecicationsandcapacityofthememory.

CPU0

CPU1

DIMM_P0_H0

DIMM_P0_G0

DIMM_P0_F0

DIMM_P0_E0

DIMM_P0_A0

DIMM_P0_B0

DIMM_P0_C0

DIMM_P0_D0

DIMM_P1_L0

DIMM_P1_K0

DIMM_P1_J0

DIMM_P1_I0

DIMM_P1_M0

DIMM_P1_N0

DIMM_P1_O0

DIMM_P1_P0

Hardware Installation - 15 -

1-4-2 Installing and Removing the Memory Module

Before installing a memory module, make sure to turn off the computer and unplug the

power cord from the power outlet to prevent damage to the memory module.

Be sure to install DDR4 DIMMs on to this motherboard.

Follow these instructions to install a DIMM module:

1. Insert the DIMM memory module vertically into the DIMM slot and push it down.

2. Close the plastic clip at both edges of the DIMM slots to lock the DIMM module.

3. Reverse the installation steps when you want to remove the DIMM module.

1

2

1-4-3 DIMM Population Table

Type Ranks Per DIMM

and Data Width

DIMM

Capacity (GB)

Speed (MT/s); Voltage (V);

Slots per Channel(SPC) and

DIMM per Channel (DPC)

1 Slot per

Channel

2 Slots per

Channel

DIMM Density 1DPC 1DPC 2DPC

8Gb 1.2V 1.2V 1.2V

RDIMM SRx4 16GB 3200 3200 3200

RDIMM DRx8 16GB

- 16 - Hardware Installation

1-4-4 Altra Platform DDR4 Suggest Conguration Table

4 DIMM

Memory Q’ty

for each CPU

CPU1

M0 N0 O0 P0 L0 K0 J0 I0

V

1 DIMM

2 DIMM

6 DIMM

8 DIMM

V

V V

VVVV

V VV

V

VVVV

V VV

CPU0

E0 F0 G0 H0 D0 C0 B0 A0

V

V V

VVVV

VV V V VVV

V V V VV V

V

Hardware Installation - 17 -

1-5 Installing and Removing the M.2 SSD Module

Follow the steps below to install an optional M.2 SSD module on your motherboard.

Step1. Insert the M.2 SSD module into the slot.

Step2. Secure it with the screw, tightening as necessary to fasten the M.2 SSD module in place.

1

2

- 18 - Hardware Installation

1-6 Back Panel Connectors

uDebug Port

Connects to USB-DB9 console for debug log.

v10/100/1000 Server Management LAN Port

The LAN port provides Internet connection with data transfer speeds of 10/100/1000Mbps. This port is

the dedicated LAN port for Server Management.

wUSB 3.2 Gen1 Ports

The USB port supports the USB 3.0 specification. Use this port for USB devices such as a USB

keyboard/mouse,USBprinter,USBashdriveetc.

x10GBASE-T RJ-45 LAN Port #1

The 10 Gigabit Ethernet LAN port provides Internet connection at up to 10 Gbps data rate. See the

section below for a description of the states of the LAN port LEDs.

y10GBASE-T RJ-45 LAN Port #2

The 10 Gigabit Ethernet LAN port provides Internet connection at up to 10 Gbps data rate. See the

section below for a description of the states of the LAN port LEDs.

zID button with LED

Whenthesystemidenticationisactive,theIDLEDonthefront/backpanelglowsblue.

{VGA Port

Connects to a monitor device.

v

x y z

{

u

LAN and ID Button LEDs

Link/Activity LED

Speed LED

LAN Port

• Whenremovingthecableconnectedtoabackpanelconnector,rstremovethecablefromyour

device and then remove it from the motherboard.

• When removing the cable, pull it straight out from the connector. Do not rock it side to side to

prevent an electrical short inside the cable connector.

ID button/LED:

10/100/1000 LAN LED:

State Description

Yellow On 1Gbps data rate

Green On 100Mbps data rate

Off 10Mbps data rate

State Description

Blue On Systemidenticationisactive

Off Systemidenticationisdisabled

10GbE LAN LED:

State Description

Yellow On 5Gbps, 2.5Gbps, 1Gps data rate

Green On 10Gbps data rate

Off 100Mbps data rate

w

Hardware Installation - 19 -

1-7 Internal Connectors

Read the following guidelines before connecting external devices:

• First make sure your devices are compliant with the connectors you wish to connect.

• Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

• After installing the device and before turning on the computer, make sure the device cable has

been securely attached to the connector on the motherboard.

1) ATX1 11) F_USB2

2) P12V_1 (for CPU0) 12) F_USB1

3) P12V_2 (for CPU1) 13) FP_1

4) SATA3 14) BP_1

5) SATA2 15) CON1

6) CPU0_FAN 16) IPMB1

7) CPU1_FAN 17) LED_BMC1

8) SYS_FAN0 18) BAT1

9) SYS_FAN1 -- --

10) PMBUS1 -- --

CPU0

CPU1

DIMM_P0_H0

DIMM_P0_G0

DIMM_P0_F0

DIMM_P0_E0

DIMM_P0_A0

DIMM_P0_B0

DIMM_P0_C0

DIMM_P0_D0

DIMM_P1_L0

DIMM_P1_K0

DIMM_P1_J0

DIMM_P1_I0

DIMM_P1_M0

DIMM_P1_N0

DIMM_P1_O0

DIMM_P1_P0

10

18

1

2

3

45

6

7

8

9

11

12

13

14

15

16

17

- 20 - Hardware Installation

1/2/3) ATX1/P12V_1/P12V_2 (2x12 Main Power Connector and 2x4 12V Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the components

onthemotherboard.Beforeconnectingthepowerconnector,rstmakesurethepowersupplyisturnedoff

and all devices are properly installed. The power connector possesses a foolproof design. Connect the power

supply cable to the power connector in the correct orientation. The 12V power connector mainly supplies

power to the CPU. If the 12V power connector is not connected, the computer will not start.

To meet expansion requirements, it is recommended that a power supply that can withstand high

power consumption be used (500W or greater). If a power supply is used that does not provide the

required power, the result can lead to an unstable or unbootable system.

ATX

P12V_1/ P12V_2

85

41

PinNo. Denition

1 GND

2 GND

3 GND

4 GND

5 +12V

6 +12V

7 +12V

8 +12V

113

1224

Pin No. Denition Pin No. Denition

1 3.3V 13 3.3V

2 3.3V 14 -12V

3 GND 15 GND

4 +5V 16 PS_ON

5 GND 17 GND

6 +5V 18 GND

7 GND 19 GND

8 Power Good 20 -5V

9 5VSB 21 +5V

10 +12V 22 +5V

11 +12V 23 +5V

12 3.3V 24 GND

Page is loading ...

Gigabyte MP72-HB0 User manual

Related papers

Other documents