AIC SB202-TU User manual

UM_SB202-TU_v1.6_052623

SB202-TU

Storage Barebone

User's Manual

Document Release History

Release Date Version Update Content

September,

2022 1 Released to public.

October, 2022 1.1 BP update.

October, 2022 1.2 System block diagram update.

November, 2022 1.3 CPU location: JCPU1 (CPU0)/ JCPU2 (CPU1)

December, 2022 1.4 Add OCP 3.0 and PCIe installation.

February, 2023 1.5 Correct OCP 3.0 adapter info.

May, 2023 1.6 Add BP content.

Preface �� i

Safety Instructions �� ii

About This Manual �� iv

Chapter 1� Product Features �� 1

1.1 Box Contents ............................................................................................ 1

1.2 Specifications ............................................................................................ 2

1.3 System Block Diagram .............................................................................. 3

1.4 Features ..................................................................................................... 4

Chapter 2� Hardware Setup �� 7

2.1 Central Processing Unit ........................................................................... 7

2.1.1 Installation ............................................................................................................ 7

2.2 System Memory ...................................................................................... 12

2.2.1 Placement ...........................................................................................................12

2.2.2 DIMM Population ...............................................................................................13

2.2.3 Installation ..........................................................................................................14

2.3 Top Cover ................................................................................................ 15

2.4 Power Supply Unit ................................................................................... 16

2.4.1 Installation ..........................................................................................................16

2.4.2 LED Indicator ......................................................................................................16

2.5 Fan ............................................................................................................ 17

2.6 Disk Drive ................................................................................................ 18

2.6.1 Disk Drive: 2.5-inch .............................................................................................18

2.6.1 Disk Drive: 3.5-inch .............................................................................................19

2.6.2 LED Indicator ......................................................................................................20

2.6.3 Drive Slot Map ....................................................................................................20

2.7 M.2 SSD (NGFF) Card ............................................................................. 21

2.8 Retimer Card ........................................................................................... 22

2.9 OCP 3.0 Ethernet adapter ...................................................................... 23

2.10 PCIe Card .............................................................................................. 26

2.11 Slide Rail ............................................................................................... 27

Chapter 3� Hardware Settings �� 30

3.1 Block Diagram ......................................................................................... 30

3.2 Placement ................................................................................................ 31

3.3 Content List ............................................................................................. 32

3.4 External Port ............................................................................................ 34

3.5 Connector Definition ............................................................................... 35

3.6 Jumper Definition .................................................................................... 47

3.7 Internal LED .............................................................................................. 54

3.8 Drive Backplane: 12 Bay (SKU1) ............................................................. 55

3.8.1 Placement ...........................................................................................................55

3.8.2 Connector ...........................................................................................................56

3.8.3 LED Indicator ......................................................................................................58

3.9 Drive Backplane: 4 Bay (SKU2/3/4) ........................................................ 59

3.9.1 Placement ...........................................................................................................59

3.9.2 Connector ...........................................................................................................59

Content

Table of Contents

3.9.3 Dip Switch Setting ..............................................................................................66

3.9.4 LED Indicator ......................................................................................................69

3.9.5 Cable Routing .....................................................................................................70

3.10 Drive Backplane: 4 Bay (SKU2/3) ......................................................... 71

3.10.1 Placement.........................................................................................................71

3.10.2 Connector .........................................................................................................72

3.10.3 LED Indicator ....................................................................................................73

3.10.4 Jumper ..............................................................................................................74

3.11 Drive Backplane: 8 Bay (SKU4) ............................................................. 75

3.11.1 Placement.........................................................................................................75

3.11.2 Connector .........................................................................................................76

3.11.3 Jumper ..............................................................................................................77

Chapter 4� BIOS Configuration Settings �� 78

4.1 Navigation Keys ....................................................................................... 78

4.2 BIOS Menu ............................................................................................... 79

4.2.1 Menu ...................................................................................................................79

4.2.2 Startup ................................................................................................................79

4.3 Main ......................................................................................................... 80

4.3.1 Main ....................................................................................................................80

4.4 Advanced ................................................................................................. 81

4.4.1 Trusted Computing ............................................................................................81

4.4.2 Serial Port Console Redirection ........................................................................82

4.4.3 SIO Configuration ............................................................................................... 82

4.4.4 PCI Subsystem Settings ....................................................................................82

4.4.5 USB Configuration ..............................................................................................82

4.4.6 Network Stack Configuration ............................................................................83

4.4.7 T1s Auth Configuration ......................................................................................83

4.4.8 RAM Disk Configuration.....................................................................................83

4.4.9 Driver Health ....................................................................................................... 83

4.5 Platform Configuration ........................................................................... 84

4.5.1 PCH Configuration .............................................................................................84

4.5.2 Server ME Configuration .................................................................................... 86

4.5.3 Server ME Debug Configuration ........................................................................86

4.5.4 Runtime Error Logging .......................................................................................87

4.6 Socket Configuration ............................................................................... 88

4.6.1 Processor Configuration ....................................................................................88

4.6.2 Common RefCode Configuration ...................................................................... 89

4.6.3 Memory Configuration ....................................................................................... 89

4.6.4 IIO Configuration ................................................................................................90

4.6.5 Advanced Power Management Configuration .................................................91

4.7 Server Mangement .................................................................................. 95

4.7.1 Processor Configuration ....................................................................................95

4.7.2 System Event Log ...............................................................................................96

4.7.3 BMC Network Configuration ..............................................................................96

4.8 Security .................................................................................................... 97

4.9 Boot .......................................................................................................... 98

4.10 Exit .......................................................................................................... 99

4.11 BIOS Update Process .......................................................................... 100

Content

Chapter 5� BMC Configuration Settings �� 101

5.1 Login .......................................................................................................101

5.2 Web GUI .................................................................................................102

5.2.1 Menu Bar ...........................................................................................................102

5.2.2 Dashboard ........................................................................................................103

5.2.3 Sensor ...............................................................................................................104

5.2.4 System Inventory ..............................................................................................104

5.2.5 FRU Information ...............................................................................................105

5.2.6 Log & Reports ...................................................................................................106

5.2.7 Settings .............................................................................................................107

5.2.8 Remote Control ................................................................................................108

5.2.9 Images Redirection ..........................................................................................110

5.2.10 Power Control ................................................................................................. 111

5.2.11 Maintenance Group........................................................................................112

5.2.11.1 Firmware Update ..............................................................................................113

5.2.11.2 BIOS Firmware Update ....................................................................................118

5.2.12 Sign Out ..........................................................................................................121

Chapter 6� Technical Support �� 122

This document contains proprietary information about

AIC® products and is not to be disclosed or used except in

accordance with applicable agreements.

Copyright

No part of this publication may be reproduced, stored in a retrieval system, or

transmitted in any form or by any means, electronic, mechanical, photo-static, recording

or otherwise, without the prior written consent of the manufacturer.

Trademarks

All products and trade names used in this document are trademarks or registered

trademarks of their respective holders.

Changes

The material in this document is for information purposes only and is subject to change

without notice.

Warning

1. A shielded-type power cord is required in order to meet FCC emission limits and also

to prevent interference to the nearby radio and television reception. It is essential

that only the supplied power cord be used.

2. Use only shielded cables to connect I/O devices to this equipment.

3. You are cautioned that changes or modifications not expressly approved by the

party responsible for compliance could void your authority to operate the equipment.

Disclaimer

AIC® shall not be liable for technical or editorial errors or omissions contained herein.

The information provided is provided "as is" without warranty of any kind. To the extent

permitted by law, neither AIC® or its aliates, subcontractors or suppliers will be liable

for incidental, special or consequential damages including downtime cost; lost prots;

damages relating to the procurement of substitute products or services; or damages

for loss of data, or software restoration. The information in this document is subject to

change without notice.

Instruction Symbols

Special attention should be given to the instruction symbols below.

NOTE This symbol indicates that there is an explanatory or

supplementary instruction.

CAUTION

This symbol denotes possible hardware impairment. Up most

precaution must be taken to prevent serious hardware damage.

WARNING

This symbol serves as a warning alert for potential body

injury. The user may suffer possible injury from disregard or

lack of attention.

Preface

i

Before you commence, please attentively read the following important discretions below. All

cautions and warnings on the equipment or in the manuals should be circumspectly noted

and reviewed.

Always ground yourself to prevent static electricity.Always ground yourself to prevent static electricity.

請請全程接地，以防止靜電。全程接地，以防止靜電。

请请全程接地，以防止静电。全程接地，以防止静电。

Всегда заземляйте себя, чтобы избежать статического электричества.Всегда заземляйте себя, чтобы избежать статического электричества.

Aard jezelf altijd om statische elektriciteit te voorkomen.Aard jezelf altijd om statische elektriciteit te voorkomen.

• Firmly ground yourself at all times when installing or assembling the internal

components of the server. Most of electronic components in the server are highly

sensitive to electrical static discharge.

• Use a solid grounding wrist strap and distinctively place all electronic components in

static-shielded devices to prevent static. Grounding wrist straps can be purchased in

any electronic supply store.

• Confirm that the power source is turned off and then disconnect the power cords from

your system before performing any type of installation or manual servicing. A sudden

surge of power could severely damage the sensitive electronic components.

• Do not precipitously open the system’s top cover. If you must open the cover for

maintenance purposes, only a trained technician should be allowed to proceed this

action. Integrated circuits on computer boards are highly sensitive to static electricity.

Before operating a board or integrated circuit, touch an unpainted portion of the system

unit chassis for a couple of seconds to discharge any static electricity on your body.

Place the server in a stable environment. Place the server in a stable environment.

請請將伺服器放置在穩定的環境中。將伺服器放置在穩定的環境中。

请请将伺服器放置在稳定的环境中。将伺服器放置在稳定的环境中。

Поместите сервер в стабильную среду.Поместите сервер в стабильную среду.

Plaats de server in een stabiele omgeving.Plaats de server in een stabiele omgeving.

• Place this equipment on a stable surface when installing. A small mild drop or fall could

cause fatal injury to both the equipment and the person handling the equipment.

• Please keep this equipment away from humidity to prevent vast rust and disintegration.

• Carefully and accurately mount the equipment into the rack. Uneven mechanical

loading may lead to hazardous consequences.

• This equipment is to be installed for operation in an environment with maximum

ambient temperature below 35°C.

• Review the environment before performing any installation or servicing. Keep the

equipment away from hazardous and uneven grounds.

• This server must be installed only in Restricted Access Locations.

Handle equipment with care.Handle equipment with care.

請謹慎操作設備。請謹慎操作設備。

请谨慎操作设备。请谨慎操作设备。

Обращайтесь с оборудованием осторожно.Обращайтесь с оборудованием осторожно.

Behandel de apparatuur voorzichtig.Behandel de apparatuur voorzichtig.

• Do not cover the openings of the system. The openings on the system are for air

convection, which intentionally protect the equipment from overheating.

• Never pour any liquid into ventilation openings of the system. This could cause

catastrophic fire or electrical shock.

Safety Instructions

ii

• Ensure that the voltage of the power source is within the specification on the label

when connecting the equipment to the power outlet. The current load and output power

of loads must be within the specification.

• This equipment must be firmly connected to reliable grounding before usage. Pay

special attention to power supplied other than direct connections, e.g. using of power

strips.

• Place the power cord out of the way of foot traffic. Do not place anything over the

power cord. The power cord must be rated for the product, voltage and current marked

on the product’s electrical ratings label. The voltage and current rating of the cord

should be greater than the voltage and current rating marked on the product.

Pay attention to hardware maintenance.Pay attention to hardware maintenance.

注意硬體維護注意硬體維護。。

注意硬体维护注意硬体维护。。

Обратите внимание на обслуживание оборудования.Обратите внимание на обслуживание оборудования.

Besteed aandacht aan hardware-onderhoud.Besteed aandacht aan hardware-onderhoud.

• If the equipment is not used for a long time, disconnect the equipment from mains to

avoid being damaged by transient over-voltage.

• Module and drive bays must not be empty. They must have a dummy cover.

• Never open the equipment without professional assistance. For safety reasons, only

qualified service personnel should open the equipment.

• If one of the following situations arise, the equipment should be checked and tested by

service personnel:

1. The power cord or plug is damaged.

2. Liquid has penetrated the equipment.

3. The equipment has been exposed to moisture.

4. The equipment does not work well or will not work according to its user manual.

5. The equipment has been dropped and/or damaged.

6. The equipment has obvious signs of breakage.

7. Please disconnect this equipment from the AC outlet before cleaning. Do not

use liquid or detergent for cleaning. The use of a moisture sheet or cloth is

recommended for cleaning.

CAUTION

The equipment intended for installation should be placed in Restricted Access Location.

CAUTION

There will be a risk of explosion if battery is replaced by an incorrect type. Dispose

of used batteries according to the instructions. After performing any installation or

servicing, make sure the enclosure is correct in position before turning on the power.

CAUTION

This unit may have more than one power supply. Disconnect all power sources before

maintenance to avoid electric shock.

iii

Thank you for selecting and purchasing the SB202-TU.

This user's manual is provided for professional technicians to perform easy hardware

setup, basic system configurations and quick software startup. This document pellucidly

presents a brief overview of the product design, device installation and firmware settings

for SB202-TU. For the latest version of this user's manual, please refer to the AIC® website:

https://www.aicipc.com/en/productdetail/51331.

Chapter 1 Product Features

SB202-TU is a flexible storage server barebone that is specifically designed to

accommodate diverse corporations and enterprises for managing heavy workloads and

multiple applications.

Chapter 2 Hardware Setup

This chapter displays an easy installation guide for assembling the hardware in this

product. Utmost caution for proceeding to set up the hardware is highly advised. Most of

the components are highly fragile and vulnerable to exterior influence. Do not endanger the

device by placing the device in an unstable environment.

Chapter 3 Motherboard Settings

This chapter elaborates the overall layout of the server motherboard, including multifarious

connectors, jumpers and LED descriptions. These descriptions assist users to configure

different settings and functions of the motherboard, as well as to confirm the placement of

each connector and jumper.

Chapter 4 BIOS Configuration Settings

This chapter introduces the key features of BIOS, including the descriptions and option

keys for diverse functions. These details provide users to effortlessly navigate and

configure the input/output devices.

Chapter 5 BMC Configuration Settings

This chapter illustrates the diverse functions of IPMI BMC, including the details on logging

into the web page and assorted definitions. These descriptions are helpful in configuring

various functions through Web GUI without entering the BIOS setup. For more information

of BMC configurations, please refer to IPMI BMC (Aspeed AST2500) User's Manual for a

more detailed description.

Chapter 6 Technical Support

For more information or suggestion, please contact the nearest AIC® corporation

representative in your district or visit the AIC® website: https://www.aicipc.com/en/index.

It is our greatest honor to provide the best service for our customers.

About This Manual

iv

1

SB202-TU is a high density storage server that includes motherboard, chassis, power supply

and disk drive. For more information about our product, please visit our website at https://

www.aicipc.com/en/index.

Before removing the subsystem from the shipping carton, visually inspect the physical con-

dition of the shipping carton. Exterior damage to the shipping carton may indicate that the

contents of the carton are damaged. If any damage is found, do not remove the compo-

nents; contact the dealer where the subsystem was purchased for further instructions. Be-

fore continuing, rst unpack the subsystem and verify that the number of components in the

shipping carton is accurate and in good condition.

1�1 Box Contents

This product contains the components listed below.

Please conrm the number and the condition of the components before installation.

Pre-installed into the system Number

1200W redundant power supply 80+ Platinum 1+1

3.5-inch hot swap disk drive tray (Front) 12

2.5-inch hot swap disk drive tray (Rear) 2

Heat sink 2

Easy swap fan 6 x 60x38mm 6

AIC® Tucana motherboard 1

Accessory Item Number

EPE foam for front board: 563*400*105H 1

EPE foam for rear board: 563*400*105H 1

EPE foam for front tray: 563*300*145H 1

EPE foam for rear tray: 563*300*145H 1

EPE pad for Rail Box: 130*100*30H 2

EPE pad: 160*100*100T 2

Power cord vary per region

28-inch tool-less slide rail assembly 1

Product features are subject to change without notice�

Chapter 1� Product Features

2

Chapter 1. Product Features

1�2 Specifications

Environmental • Storage temperature: -10°C(14°F) ~ 60°C(140°F)

• Operating temperature: 0°C(32°F) ~ 35°C(95°F)

• Storage operating humidity: 5%~95% non-condensing

Gross Weight (w/ PSU & Rail)

kgs : 26

lbs : 57.3

Packaging

Dimensions (W x D x H)

mm : 605 x 920 x 322

inches : 23.8 x 36.2 x 12.7

Mounting Standard 28" tool-less slide rail

Expansion Slots PCIe 4.0 • 3 x PCIe X16 slots (HHHL) + 1 x OCP 3.0

• 2 x PCIe X8 slots (HHHL)

System BIOS

BIOS Type

• AMI UEFI BIOS

• SPI (Serial Peripheral Interface)

FLASH Interface

BIOS Features

• ACPI

• PXE

• WOL

• AC loss recovery

• IPMI 2.0 KCS interface

• SMBIOS

• Serial console redirection

• BIOS Boot

• BIOS Recovery Mode

• SRIOV

• iSCSI

• TPM

• PCIe NTB

On-board

Devices

SATA / SAS

Intel® C621A PCH on-chip solution

• 8 x SATA 6.0 Gb/s (by 2 x mini-SAS)

• 2 x SATA 6.0 Gb/s (by 2 x SATA 7 pin)

Optional SAS 3008/3108 modules (on OCP)

IPMI

Aspeed AST2500 Advanced PCIe Graphics

& Remote Management Processor

• Baseboard Management Controller

• Intelligent Platform Interface 2.0 (IPMI 2.0)

• iKVM, Media Redirection, IPMI over LAN,

Serial over LAN

• SMASH Support

Network

Controllers

• Realtek® RTL8211EL single port 1000

Mbps Ethernet PHYceiver for dedicated

Graphics

Aspeed AST2500 Advanced PCIe Graphics

& Remote Management Processor

• PCIe VGA/2D Controller

• 1920x1200@60Hz 32bpp

Rear I/O

LAN 1 x GbE RJ45 dedicated to BMC management

USB 2 x USB 3.2 Gen1x1 Type A

VGA 1 x external DB-15 VGA port

Serial Port 1 x external COM port phone jack

Power Supply 1200W 1+1 redundant power supply 80+ Platinum

• AC INPUT : 100~240V,50/60Hz,10-5A

System Cooling 6 x 60x38mm easy swap fans

System

Management

• IPMI 2.0

• KVM over IP

• Media redirection

• Temperature, fan, voltage,

PSU sensor monitor

• System temperature

• System ID /

System fail indicator

• Remote power on/off/reset

• SEL message alarm

through mail

• SNMP support

• Intel NM

Dimensions

(W x D x H)

mm : 430 x 680 x 88.2

inches : 17 x 26.8 x 3.5

Motherboard AIC Server Board Tucana

Processor

Support

• 3rd Gen Intel® Xeon® Scalable Processors

(Ice Lake)

• Supports CPU TDP up to 270W

*Use over 165W CPU, please contact AIC

Technical Support for more info/details about

optimized CPUs and specialized system.

QPI Speeds11.2 GT/s

Socket Type Socket P+ (LGA-4189)

Chipset Support Intel® C621A Chipset

System Memory

• 8 x memory channels per CPU, 1 x DIMM per channel

• 16 x DIMM slots support: DDR4 REG ECC 3200/2933/2666

• Intel® Optane™ Persistent Memory 200 (Barlow Pass) support

Front Panel System power on/off, System ID, System reset, 1x USB 3.0 Type A

LEDs Power status, System alert, LAN activity, Drive activity, System ID

Drive Bays

External

3.5" hot swap 12

2

Internal M.2 2 x M.2(NGFF)/M-Key/2280

Backplane Options

SKU1: 1 x 12-port 12Gb SAS 28-PHY expander

backplane

SKU2: 2 x 4-port 12G SAS backplane + 1 x 4-port

12G SAS/PCIe Gen4 NVMe Tir-mode backplane

SKU3: 2 x 4-port 12G SAS / PCIe Gen4 NVMe

Tri-mode backplane +1 x 4-port 12G SAS backplane

SKU4: 3 x 4-port 12G SAS/PCIe Gen4 NVMe

Tri-mode backplane(Additional Tri-mode/PCIe

Switch/Retimer card required)

2.5” hot swap (rear)

3

Chapter 1. Product Features

1�3 System Block Diagram

4

Chapter 1. Product Features

SB202-TU is a reliable 2U storage server barebone with 12 hot swap drives bays. This prod-

uct is designed to accommodate the AIC-patented serverboard, Tucana, which supports

two Intel® Xeon® Scalable Processors and 16 DDR4 DIMM to offer greater performance,

efficiency and utility for our customers. Featuring Intel® C621A Series Chipset, which is

emphasized for its accelerated speed and expansion, this product enhances these advan-

tages by integrating flexible IO usage and system expansion into to provide greater band-

width and utilization.

In addition to the noteworthy features of the barebone, SB202-TU provides immediate and

efficient management with Onboard Baseboard Management Controller and greater I/O

extension. Featuring IPMI 2.0 and Aspeed AST2500 Advanced PCIe Graphics, the server

board offers support for iKVM, Media Redirection, Smash Support, IPMI over LAN and Seri-

al over LAN.

• 2U 12-Bay storage server with SATA/SAS3/NVMe drives support

• Supports 3rd Gen. Intel® Xeon® Scalable processors (Ice Lake)

• Intel® C621A Chipset to provide 5+ years product life cycle

• Onboard Baseboard Management Controller for system management and IPMI control

• Dedicated BMC management port

• Front-to-back airow and hot swap redundant fans to provide optimal thermal conditions

1�4 Features

5

Chapter 1. Product Features

Front Panel

System LED Indicator and switch

Item Description Item Description

Power Button LAN LED

Power Status LED System Reset Button

Drive Activity LED System Alert LED

System ID LED ID Button

Indicator Color Description

Power Status LED Green System is on.

Off System is off.

Drive Activity LED Yellow (Blinking) HDD activity is detected.

Off HDD activity is not detected.

LAN Activity LED Yellow (Blinking) LAN1 activity is detected.

System Alert LED Red

Critical system failure is detected.

(processors, memory, voltage

regulations, thermal events, fan

failures, NMI, etc.)

Off No critical failure is detected.

System ID LED Blue ID activity is detected.

Off ID activity is not detected.

Disk Drive

Rear Panel

    

Item Description

11200W 1+1 redundant power supply 80+ Platinum

• AC INPUT : 100~240V,50/60Hz,10-5A

2 2 x 2.5-inch hot swap disk drive bays (7mm)

3 OCP 3.0 slot

4 1 x external COM port phone jack

5 2 x USB 3.2 Gen1x1 Type A in double-stack connector

6 1 x GbE RJ45 dedicated to BMC management port

7 3 x PCIe X16 slots (HHHL) / 2 x PCIe X8 slots (HHHL)

6

Chapter 1. Product Features

Top View

Item Description

1 1200W 1+1 redundant power supply 80+Platinum

2 6 x 60x38mm easy swap fans

3 12 x 3.5-inch hot swap disk drive







7

Chapter 2� Hardware Setup

This chapter provides the graphic detail and basic instruction for hardware installation.

Turn off the system and unplug all peripheral devices before proceeding.

2�1 Central Processing Unit

The serverboard supports dual Xeon scalable processors and Socket P4 (LGA-4189).

2�1�1 Installation

To ensure a safe and easy setup, you need to prepare before installation:

 a T30 torque screwdriver

 ESD wrist strap/mat and conductive foam pad

 Safe and stable environment

CAUTION

The pins of the processor socket are vulnerable and easily susceptible to damage if ngers

or any foreign objects are pressed against them. Please keep the socket protective cover on

when the processor is not installed.

CAUTION

When unpacking a processor, hold the processor only by its edges to avoid touching the con-

tacts.

Standard Processor Assembly:

A standard processor assembly is comprised of 5 components: processor carrier,

processor, bolster plate assembly, socket and back plate.

This information is provided for professional technicians only.

Heatsink

Processor Carrier

Processor

Bolster Plate Assembl

y

LGA4189

Back plate

Dust cover

standard

processor

assembly

8

Chapter 2. Hardware Setup

Procedure:

 Remove the dust cover. Push the tab inward on both sides to remove.

 Remove the Pnp cap from the socket. Press the tabs on both sides to remove.

9

Chapter 2. Hardware Setup

 Insert the CPU into the CPU carrier. Carefully align and insert on side of the CPU and

then the other.

NOTE

Must ensure to match the direction and pin of the CPU with the carrier. Refer to

the placement of pin 1.

Integrated Heat Spreader (IHS) keying

substrate keying

Pin 1

10

Chapter 2. Hardware Setup

 Attach the heat sink onto the CPU carrier. Hook the corners of the CPU carrier to the

back side of the heat sink.

 Install the assembled heat sink and CPU carrier onto the CPU socket. Please use a T-30

torque driver tighten the nuts in the four corners of the heat sink labeled in the order

1  2  3  4.

CAUTION

Failure to tighten the heat sink screws in the specified order may cause damage to the

processor socket assembly. Heat sink screws is recommended to be tightened to 8 in-

lbs torque, but can be tightened to 12 in-lbs torque according to the indicated order on

the top of the heatsink label.

CPU carrrier

CPU socket

Heat sink with carrier

Screw tightening order









Heatsink back side

Page is loading ...

AIC SB202-TU User manual

AIC SB202-TU User manual

Related papers

Other documents