ASRock Rack EPYC3101D4I-2T User manual

EPYC3251D4I-2T

EPYC3151D4I-2T

EPYC3101D4I-2T

EPYC3251D4I-NL

EPYC3101D4I-NL

User Manual

Version 1.1

Published November 2020

Version 1.1

Published November 2020

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Rack Inc.

Products and corporate names appearing in this documentation may or may not

be registered trademarks or copyrights of their respective companies, and are used

only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished

for informational use only and subject to change without notice, and should not

be constructed as a commitment by ASRock Rack. ASRock Rack assumes no

responsibility for any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock Rack does not provide

warranty of any kind, either expressed or implied, including but not limited to

the implied warranties or conditions of merchantability or tness for a particular

purpose.

In no event shall ASRock Rack, its directors, ocers, employees, or agents be liable

for any indirect, special, incidental, or consequential damages (including damages

for loss of prots, loss of business, loss of data, interruption of business and the

like), even if ASRock Rack has been advised of the possibility of such damages

arising from any defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance

controlled in Perchlorate Best Management Practices (BMP) regulations passed by the

California Legislature. When you discard the Lithium battery in California, USA, please

follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/

perchlorate”

ASRock Rack’s Website: www.ASRockRack.com

Contact Information

If you need to contact ASRock Rack or want to know more about ASRock Rack,

you’re welcome to visit ASRock Rack’s website at www.ASRockRack.com; or you

may contact your dealer for further information.

ASRock Rack Incorporation

6F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,

Taipei City 112, Taiwan (R.O.C.)

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Specications 2

1.3 Unique Features 5

1.4 Motherboard Layout 6

1.5 Onboard LED Indicators 8

1.6 I/O Panel 9

1.7 Block Diagram 11

Chapter 2 Installation 13

2.1 Screw Holes 13

2.2 Pre-installation Precautions 13

2.3 Installation of Memory Modules (DIMM) 14

2.4 Expansion Slots (PCI Express Slots) 16

2.5 Onboard Headers and Connectors 17

2.6 AC-IN / DC-IN Power Connections 22

2.7 Unit Identication purpose LED/Switch 23

2.8 Driver Installation Guide 23

2.9 Dual LAN and Teaming Operation Guide 24

2.10 M.2_SSD (NGFF) Module Installation Guide (M2_1) 25

Chapter 3 UEFI Setup Utility 27

3.1 Introduction 27

3.1.1 UEFI Menu Bar 27

3.1.2 Navigation Keys 28

3.2 Main Screen 29

3.3 Advanced Screen 30

3.3.1 CPU Conguration 31

3.3.2 Chipset Conguration 32

3.3.3 Storage Conguration 34

3.3.4 ACPI Conguration 35

3.3.5 USB Conguration 36

3.3.6 Super IO Conguration 37

3.3.7 Serial Port Console Redirection 38

3.3.8 H/W Monitor 42

3.3.9 PSP Firmware Versions 44

3.3.10 AMD CBS 45

3.3.11 Instant Flash 46

3.4 Server Mgmt 47

3.4.1 System Event Log 48

3.4.2 BMC Network Conguration 49

3.5 Security 51

3.5.1 Key Management 52

3.6 Boot Screen 56

3.6.1 CSM Parameters 58

3.7 Event Logs 60

3.8 Exit Screen 62

Chapter 4 Software Support 63

4.1 Install Operating System 63

4.2 Support CD Information 63

4.2.1 Running The Support CD 63

4.2.2 Drivers Menu 63

4.2.3 Utilities Menu 63

4.2.4 Contact Information 63

Chapter 5 Troubleshooting 64

5.1 Troubleshooting Procedures 64

5.2 Technical Support Procedures 66

5.3 Returning Merchandise for Service 66

EPYCXXXXD4I-2T / EPYXXXXD4I-NL Series

PB 1

English

Chapter 1 Introduction

ank you for purchasing ASRock Rack EPYC3251D4I-2T / EPYC3151D4I-2T /

EPYC3101D4I-2T / EPYC3251D4I-NL / EPYC3101D4I-NL motherboard, a reliable

motherboard produced under ASRock Rack’s consistently stringent quality control.

It delivers excellent performance with robust design conforming to ASRock Rack’s

commitment to quality and endurance.

In this manual, chapter 1 and 2 contains introduction of the motherboard and step-

by-step guide to the hardware installation. Chapter 3 and 4 contains the conguration

guide to BIOS setup and information of the Support CD.

1.1 Package Contents

• ASRock Rack EPYC3251D4I-2T / EPYC3151D4I-2T / EPYC3101D4I-2T /

EPYC3251D4I-NL / EPYC3101D4I-NL Motherboard

(Mini-ITX Form Factor: 6.7-in x 6.7-in, 17.02 cm x 17.02 cm)

• Quick Installation Guide

• 1 x Oculink to 4 SATA Cable (60cm) (Optional)

• 1 x SATA3 Cable (60cm)

• 1 x SATA Power Cable (80cm)

• 1 x ATX 4P to 24P Power Cable (8cm)

• 1 x I/O Shield

• 1 x Screw for M.2 Socket

If any items are missing or appear damaged, contact your authorized dealer.

Because the motherboard specications and the BIOS soware might be updated, the con-

tent of this manual will be subject to change without notice. In case any modications of

this manual occur, the updated version will be available on ASRock Rack website without

further notice. You may nd the latest memory and CPU support lists on ASRock Rack

website as well. ASRock Rack’s Website: www.ASRockRack.com

If you require technical support related to this motherboard, please visit our website for

specic information about the model you are using.

http://www.asrockrack.com/support/

2 3

English

1.2 Specications

EPYC3251D4I-2T / EPYC3151D4I-2T / EPYC3101D4I-2T / EPYC3251D4I-NL /

EPYC3101D4I-NL

MB Physical Status

Form Factor Mini-ITX

Dimension 6.7'' x 6.7'' (17.02 cm x 17.02 cm)

Processor System

CPU Support AMD EPYC™ Embedded 3000 Series Processors

Chipset Soc

System Memory

Capacity - 4 x 288-pin DDR4 SDRAM DIMM slots

- Support up to 256GB DDR4 ECC/UDIMM, RDIMM

Type - Dual Channel DDR4 memory technology

- Support DDR4 ECC/UDIMM, RDIMM

Voltage 1.2V

DIMM Size per

DIMM

- ECC/UDIMM: 64GB, 32GB, 16GB, 8GB, 4GB

- RDIMM: 128GB, 64GB, 32GB, 16GB, 8GB, 4GB

DIMM

Frequency

- ECC/UDIMM: 2133/2400/2666 MHz

- RDIMM: 2133/2400/2666 MHz

*the max speed may vary based on SoC SKU

Expansion Slot

PCIe 3.0 x 16

SLOT7: Gen3 x16 link

Storage

SATA Controller AMD Built-in Storage: 6 x SATAIII 6.0 Gb/s (4 x SATA from

OCulink, 2 x SATAIII 6.0 Gb/s)

M.2 Slot 1 (2280/22110, supports PCIe 3.0 x4 and SATA3 shared with

SATA_4 port)

Ethernet

Interface EPYC3251D4I-2T / EPYC3151D4I-2T / EPYC3101D4I-2T:

10000/1000 Mbps

EPYC3251D4I-NL / EPYC3101D4I-NL:

N/A

LAN Controller EPYC3251D4I-2T / EPYC3151D4I-2T / EPYC3101D4I-2T:

- 2 x RJ45 10GLAN by Intel® X550-AT2

- Supports Wake-On-LAN

- Supports Energy Ecient Ethernet 802.3az

- Supports Dual LAN with Teaming function

- Supports PXE

- LAN1 Supports NCSI

EPYC3251D4I-NL / EPYC3101D4I-NL:

N/A

EPYCXXXXD4I-2T / EPYXXXXD4I-NL Series

2 3

English

Management

BMC Controller ASPEED AST2500 : IPMI (Intelligent Platform Management

Interface) 2.0 with ikvm and vMedia support

IPMI Dedicated

GLAN 1 x Realtek RTL8211E for dedicated management LAN

Features - Watch Dog

- NMI

Graphics

Controller ASPEED AST2500

Rear Panel I/O

VGA Port D-sub x 1

Lan Port

EPYC3251D4I-2T / EPYC3151D4I-2T / EPYC3101D4I-2T:

- 2 x 10GLAN RJ45(by Intel® X550-AT2 )

EPYC3251D4I-NL / EPYC3101D4I-NL:

N/A

- 1 x RJ45 Dedicated IPMI LAN port

- LAN Ports with LED (ACT/LINK LED and SPEED LED)

UID Button 1

USB 3.2 Gen1 2

Internal Connector

COM Header 1

M.2 1 x M-Key (PCIe3.0 x4 or SATAIII 6.0 Gb/s); Supports

22110/2280 form factor

Front Panel 1

Auxiliary Panel

Header 1 (include chassis intrusion, 2 front LAN LED, System LED)

TPM Header 1

IPMB Header 1

PSU_SMB1 1

USB 3.2 Gen1

Header 1 (supports 2 USB 3.2 Gen1 ports)

Fan Header 1 x CPU Fan, 2 x System Fans (1 front, 1 rear)

ATX Power 1 x (4-pin) + 1 x (8-pin) support 12V DC-IN

SATA Power 1 (for DC-IN mode)

*Caution: Misconnection may permanently damage the motherboard.

ClearCMOS 1 (short pad)

FanFail LED 3

SATA SGPIO 1

System BIOS

BIOS Ty pe 16MB AMI UEFI Legal BIOS

4 5

English

BIOS Features

- Plug and Play (PnP)

- ACPI 2.0 Compliance Wake Up Events

- SMBIOS 2.8 Support

- ASRockRack Instant Flash

Hardware Monitor

Temperature - CPU/DDR/LAN/Storage Temperature Sensing

- MB/Card Side Temperature Sensing

Fan

- CPU/Rear/Front Fan Tachometer

- CPU Quiet Fan (Allow Chassis Fan Speed Auto-Adjust by

CPU Temperature)

- CPU/Rear/Front Fan Multi-Speed Control

Voltage Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore, DRAM,

+1.1V,+1.0V, +BAT, 3VSB, 5VSB

Support OS

OS Microso® Windows®:

- Server 2019 (64 bit)

Linux:

- RedHat Enterprise Linux Server 7.4 (64 bit) / 7.6 (64 bit)

- CentOs 7.4 (64 bit) / 7.6 (64 bit)

- UBuntu 18.04 (64 bit)

* Please refer to our website for the latest OS support list.

Environment

Temperature Operation temperature: 10°C ~ 35°C / Non operation

temperature: -40°C ~ 70°C

*Install a CPU Fan when the airow through the heatsink is below 2CFM.

* For detailed product information, please visit our website: http://www.asrockrack.com

is motherboard supports Wake from on Board LAN. To use this function, please make

sure that the “Wake on Magic Packet from power o state” is enabled in Device Manager

> Intel® Ethernet Connection > Power Management. And the “PCI Devices Power On” is

enabled in UEFI SETUP UTILITY > Advanced > ACPI Conguration. Aer that, onboard

LAN1&2 can wake up S5 under OS.

If you install Intel® LAN utility, this motherboard may fail Windows® Hardware Quality

Lab (WHQL) certication tests. If you install the drivers only, it will pass the WHQL tests.

EPYCXXXXD4I-2T / EPYXXXXD4I-NL Series

4 5

English

1.3 Unique Features

ASRock Instant Flash is a BIOS ash utility embedded in Flash ROM. is conve-

nient BIOS update tool allows you to update system BIOS without entering operating

systems rst like MS-DOS or Windows®. With this utility, you can press the <F6> key

during the POST or the <F2> key to enter into the BIOS setup menu to access ASRock

Rack Instant Flash. Just launch this tool and save the new BIOS le to your USB ash

drive, oppy disk or hard drive, then you can update your BIOS only in a few clicks

without preparing an additional oppy diskette or other complicated ash utility.

Please be noted that the USB ash drive or hard drive must use FAT32/16/12 le

system.

6 7

English

1.4 Motherboard Layout

11

DDR4_B1 (64 bit, 288-pin module, Blue)DDR4,

DDR4_B2 (64 bit, 288-pin module,)DDR4, White

17.0cm (6.7 in)

FAN2

IPMB_1

1

DDR4_A1 (64 bit, 288-pin module, Blue)DDR4,

DDR4_A2 DDR4, White(64 bit, 288-pin module,)

1

PSU_SMB1

FAN3

BAT1

VGA1

UID1

FAN1

6

7

ATX12V2

ATX12V1

OCU1

PCIE7

NUT110

PCIE7

M2_1

NUT80

ATX12V3

SATA_5

SATA_4

1

SATA_SGPIO1

1

USB3_3_4

PANEL1

HDLED RESET

PLED PWRBTN

1

ITX_AUX_PANEL1

1

COM1 TPM1

USB 3.2 Gen1

T: USB2

B: USB1

IPMI

LAN

X550_LAN1

X550_LAN2

17.0cm (6.7 in)

3

2

ASPEED

AST2500

Intel

X550

145

8

9

10

11

12

13

14

15

16

17

19

2021 18

(NCSI)

EPYC3251D4I-2T /

EPYC3151D4I-2T /

EPYC3101D4I-2T only

EPYC3251D4I-2T /

EPYC3151D4I-2T /

EPYC3101D4I-2T only

(SATAPower)

EPYC3251D4I-2T /

EPYC3151D4I-2T /

EPYC3101D4I-2T only

EPYCXXXXD4I-2T / EPYXXXXD4I-NL Series

6 7

English

No. Description

1 Rear Fan Connector (FAN2)

2 Intelligent Platform Management Bus header (IPMB_1)

3 ATX 12V Power Connector (ATX12V1)

4 ATX 4-PIN Power Connector (ATX12V2 (ATX 24pin-to-4pin))***

5PSU SMBus (PSU_SMB1)

6 2 x 288-pin DDR4 DIMM Slots (DDR4_B1, DDR4_B2)*

7 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_A2)*

8 Front Fan Connector (FAN3)

9 CPU Fan Connector (FAN1)

10 OCuLink x4 Connector (OCU1)

11 SATA3 Connector (SATA_4)**

12 SATA3 Connector (SATA_5)

13 SATA SGPIO Connector (SATA_SGPIO1)

14 M.2 Socket (M2_1) (Type 2280/22110)**

15 SATA Power Connector (ATX12V3)***

16 USB 3.2 Gen1 Header (USB3_3_4)

17 System Panel Header (PANEL1)

18 Clear CMOS Pad (CLRMOS1)

19 Auxiliary Panel Header (ITX_AUX_PANEL1)

20 TPM Header (TPM1)

21 COM Port Header (COM1)

*For DIMM installation and conguration instructions, please see p.14 (Installation of Memory Modules

(DIMM)) for more details.

** If M2_1 is occupied by a SATA-type M.2 device, SATA_4 will be disabled.

***Caution: Misconnection between the ATX12V2 and the ATX12V3 connectors may permanently damage the

motherboard.

8 9

English

1.5 Onboard LED Indicators

11

DDR4_B1 (64 bit, 288-pin module, Blue)DDR4,

DDR4_B2 (64 bit, 288-pin module,)DDR4, White

FAN2

1

DDR4_A1 (64 bit, 288-pin module, Blue)DDR4,

DDR4_A2 DDR4, White(64 bit, 288-pin module,)

1

FAN3

BAT1

VGA1

UID1

FAN1

1

HDLED RESET

PLED PWRBTN

1

PCIE7

12

3

4

5

NUT110NUT80

No. Item Status Description

1LED_FAN2 Amber FAN2 failed

2 SB_PWR1 Green STB PWR ready

3LED_FAN3 Amber FAN3 failed

4LED_FAN1 Amber FAN1 failed

5BMC_LED1 Green BMC heartbeat LED

EPYCXXXXD4I-2T / EPYXXXXD4I-NL Series

8 9

English

1.6 I/O Panel

25

3

16

4

No. Description No. Description

1 UID Switch/LED (UID1) 4 Dedicated IPMI LAN Port*

2VGA Port (VGA1) 5

EPYC3251D4I-2T / EPYC3151D4I-2T /

EPYC3101D4I-2T:

10G LAN RJ-45 Port (LAN1)**

EPYC3251D4I-NL / EPYC3101D4I-NL:

N/A

3 USB 3.2 Gen1 Ports (USB3_1_2) 6

EPYC3251D4I-2T / EPYC3151D4I-2T /

EPYC3101D4I-2T:

10G LAN RJ-45 Port (LAN2)**

EPYC3251D4I-NL / EPYC3101D4I-NL:

N/A

LAN Port LED Indications

*ere are two LED next to the LAN port. Please refer to the table below for the LAN port

LED indications.

Dedicated IPMI LAN Port LED Indications

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10M bps connection or no

link

Blinking Yellow Data Activity Yellow 100M bps connection

On Link Green 1G bps connection

ACT/LINK LED

SPEED LED

LAN Port

10 11

English

**ere are two LEDs on each LAN port. Please refer to the table below for the LAN port

LED indications.

10G LAN Port (LAN1, LAN2) LED Indications

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 100Mbps connection or

no link

Blinking Green Data Activity Yellow 1Gbps connection

On Link Green 10Gbps connection

ACT/LINK LED

SPEED LED

LAN Port

EPYCXXXXD4I-2T / EPYXXXXD4I-NL Series

10 11

English

1.7 Block Diagram

EPYC3251D4I-2T / EPYC3151D4I-2T / EPYC3101D4I-2T

CH. A

DDR4 DIMM

1866/2133 w ECC

(2) 288-pin DDR4

U/R/LR DIMM slots

AMD EPYC™

Embedded

3000 Series

4-16 Core

SoC

(SP4/SP4r2)

PCIe3.0 x16

DDR4 DIMM

1866/2133 w ECC

CH. B

DDR4 DIMM

1866/2133 w ECC

(2) 288-pin DDR4

U/R/LR DIMM slots

DDR4 DIMM

1866/2133 w ECC

Slot 7 x16 witch

M.2 M-Key

22110/2280/ 1x SATA 3

PCIe 3.0 x4

X550

PCIe3.0 x4 2 x 10G Base-T

2x USB 3.1 Gen1/USB 2.0

Rear USB

TPM Header

AST2500

LPC

PCIe x1

Switch

RGMII

UART

VGA

PHY

Mgmt. Port

COM Port

D-sub

BIOS

Flash

1x USB2.0

1x SATA 3

NC-SI

Switch

2x USB 3.1 Gen1 Header

USB

Hub 2x USB2.0

1x USB 2.0

(Not pin2pin 1GbE i350)

PCIe3.0 x4/4x SATA 3

Oculink 4i

PCIe3.0 x8/8x SATA 3

(2) Oculink 4i

N2

N1

N1: X550AT2 is not pin to pin comaptible with i350 1GbE controller

N2: SP4 SKU can support 2 more PCIex4/SATA3 and 1 PCIex4 Oculink

SP4 SKU has total 24 lanes left

12 13

English

EPYC3251D4I-NL / EPYC3101D4I-NL

CH. A

DDR4 DIMM

1866/2133 w ECC

(2) 288-pin DDR4

U/R/LR DIMM slots

AMD EPYC™

Embedded

3000 Series

4-16 Core

SoC

(SP4/SP4r2)

PCIe3.0 x16

DDR4 DIMM

1866/2133 w ECC

CH. B

DDR4 DIMM

1866/2133 w ECC

(2) 288-pin DDR4

U/R/LR DIMM slots

DDR4 DIMM

1866/2133 w ECC

Slot 7 x16 witch

M.2 M-Key

22110/2280/ 1x SATA 3

PCIe 3.0 x4

2x USB 3.1 Gen1/USB 2.0

Rear USB

TPM Header

AST2500

LPC

PCIe x1

Switch

RGMII

UART

VGA

PHY

Mgmt. Port

COM Port

D-sub

BIOS

Flash

1x USB2.0

1x SATA 3

Switch

2x USB 3.1 Gen1 Header

USB

Hub 2x USB2.0

1x USB 2.0

PCIe3.0 x4/4x SATA 3

Oculink 4i

PCIe3.0 x8/8x SATA 3

(2) Oculink 4i

N1

N1: SP4 SKU can support 2 more PCIex4/SATA3 and 1 PCIex4 Oculink

SP4 SKU has total 24 lanes left

EPYCXXXXD4I-2T / EPYXXXXD4I-NL Series

12 13

English

Chapter 2 Installation

This is a Mini-ITX form factor (6.7'' x 6.7'', 17.0 cm x 17.0 cm) motherboard. Before

you install the motherboard, study the conguration of your chassis to ensure that the

motherboard ts into it.

2.1 Screw Holes

Place screws into the holes indicated by circles to secure the motherboard to the chassis.

2.2 Pre-installation Precautions

Take note of the following precautions before you install motherboard components or

change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any components.

2. To avoid damaging the motherboard’s components due to static electricity, NEVER

place your motherboard directly on the carpet or the like. Also remember to use a

grounded wrist strap or touch a safety grounded object before you handle the compo-

nents.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded anti-static pad or in

the bag that comes with the component.

5. When placing screws into the screw holes to secure the motherboard to the chassis,

please do not over-tighten the screws! Doing so may damage the motherboard.

Make sure to unplug the power cord before installing or removing the motherboard. Failure

to do so may cause physical injuries to you and damages to motherboard components.

Do not over-tighten the screws! Doing so may damage the motherboard.

Before you install or remove any component, ensure that the power is switched o or the

power cord is detached from the power supply. Failure to do so may cause severe damage to

the motherboard, peripherals, and/or components.

14 15

English

2.3 Installation of Memory Modules (DIMM)

is motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots, and

supports Dual Channel Memory Technology.

Dual Channel Memory Conguration

Priority DDR4_A1

(Blue)

DDR4_A2

(White)

DDR4_B1

(Blue)

DDR4_B2

(White)

1Populated Populated

2Populated Populated Populated Populated

*Since installing three memory modules is NOT supported on this motherboard, we suggest not using

this conguration.

1. For dual channel conguration, you always need to install identical (the same brand,

speed, size and chip-type) DDR4 DIMM pairs.

2. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot;

otherwise, this motherboard and DIMM may be damaged.

3. Please install the memory module on CH0_A1 for the rst priority.

4. To activate Dual Channel Memory Technology, please follow the “Dual Channel Memory

Conguration” table below.

e DIMM only ts in one correct orientation. It will cause permanent damage to the

motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

Page is loading ...

ASRock Rack EPYC3101D4I-2T User manual

ASRock Rack EPYC3101D4I-2T User manual

Related papers

Other documents