RAB Lighting CRLEDFA-4R-12S-9CCT-UNV-WS 4 Inch 6 Inch 8 Inch 10 Inch Recessed Commercial Downlight FA Operating instructions

Brand: RAB Lighting

Model: CRLEDFA-4R-12S-9CCT-UNV-WS 4 Inch 6 Inch 8 Inch 10 Inch Recessed Commercial Downlight FA

Type: Operating instructions

and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: mar[email protected]

INSTRUCTIONS

4" 6" 8" 10" Recessed Commercial Downlight FA

CRLEDFA-4R-12S-9CCT-UNV-WS

CRLEDFA-6R-24S-9CCT-UNV-WS

CRLEDFA-8R-33S-9CCT-UNV-WS

CRLEDFA-10R-43S-9CCT-UNV-WS

MI PORTANT

WARNINGS:

•

Risk of electrical shock. Disconnect power at fuse or circuit breaker before installing or servicing.

To prevent early lamp failure, lamp should only be installed in operating environments ranging between-30°C and +40°C

(-22°F and+104°F).

No user serviceable parts inside. To avoid electrical shock do not disassemble product.

Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation

To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

Installers should not disconnect existing wires from lampholder terminals to make new connections at lampholder

terminals, Instead installers should cut existing lampholder leads away from the lampholder and make new electrical

connections to lampholder lead wires by employing applicable connectors.

by authorities having jurisdiction.

appropriate electrical codes. The installation guide does not supersede local national regulations for electrical installations.

This device is not intended for use with emergency exits.

Min.90°C supply conductors.

CAREFULLY BEFORE INSTALLING FIXTURE. R TAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. READ E

required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON

FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WHAT’S IN THE BOX TOOLS NEEDED

Downlight (1)

Template (1)Lumi Sticker (1)

DO NOT TO INSTALL OR OPERATE INCANDESCENT LAMPS IN THIS LUMINAIRE

AT T TEMP

THIS LUMINAIRE HAS BEEN MODIFIED TO OPERATE LED LAMPS.

REPLACE ONLY WITH RAB Lighting Inc.

RABLIGHTING.COM 888 722-1000

MODEL#

MC connector (1)

Installers should examine all parts that are not intended to be replaced by the retroﬁt kit for damage and replace any

damaged parts prior to installation of the retroﬁt kit.

•

The

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Risk of ﬁre or electric shock, LED Retroﬁt Kit installation requires knowledge of luminaires electrical systems. If not qualiﬁed,

do not attempt installation. Contact a qualiﬁed electrician.

Risk of ﬁre or electric shock, Install this kit only in luminaires that have the construction features and min dimensions shown

in below and where the input rating of the retroﬁt kit does not exceed the input rating of the luminaire.

4" 6" 8" 10" Recessed Commercial Downlight FA

and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]

INSTRUCTIONS

(cont’d)

DLPLATE/C3468R/NB

Mounting plate with nailer bar

DLFRAME/C6R

DLFRAME/C8R

Frame

OPTIONAL ACCESSORIES OPTIONAL ACCESSORIES

Plate

Goof Ring

DL4-6GOOF/R/P/CRLEDFA

For use with 6" ceiling hole applications

DL6-8GOOF/R/P/CRLEDFA

For use with 8" ceiling hole applications

DL8-10GOOF/R/P/CRLEDFA

For use with 10" ceiling hole applications

DL8-12GOOF/R/P/CRLEDFA

For use with 12" ceiling hole applications

DL10-12GOOF/R/P/CRLEDFA

For use with 12" ceiling hole applications

Visit rablighting.com for the downlight accessory compatibility lists.

4" 6" 8" 10" Recessed Commercial Downlight FA

Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.

and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]

INSTRUCTIONS

Fig: 10

5. Remove J-Box metal plate with existing lamp ballast. Do

not dispose. Disconnect all wires from the ballast. (Fig.4)

6. Remove the existing lamp metal conduit (MC) cable from

the J-Box. (Fig.5)

10. Install the junction box cover plate (with lamp ballast still attached

to it). (Fig.9)

12. Turn power ON and start saving $$.

the ceiling. (Fig.10)

9. Wire nut the ground (green) wire in the junction box. Wire

nut the black input wire with the black wire from the MC

cable and wire nut the white input wire with the white wire

from the MC cable. Wire nut the purple input wire with the

purple wire from the MC cable and wire nut the pink input

wire with the pink wire from the MC cable. If the purple and

pink wires are not in use, cap these with wire nuts. (Fig.8)

Fig: 4

Fig: 8

Fig: 9

Fig: 6

Fig: 7

Fig: 5

2. Remove CFL, Incandescent or HID lamp.

3. Remove reector from rough-in (mounting frame). (Fig.2)

(Fig.1)

Fig: 1

(Fig.3)

Fig: 2

Fig: 3

INSTALLATION WITH EXISTING FRAME INSTALLATION WITH EXISTING FRAME (cont’d)

7. Select desired lumen and CCT level using switch on driver box.

(Fig.6)

(Fig.7)

4" 6" 8" 10" Recessed Commercial Downlight FA

and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]

INSTRUCTIONS

INSTALLATION WITHOUT EXISTING FRAME

Fig: 12

2. Select desired lumen and CCT level using switch on driver box.

(Fig.12)

Fig: 13

Fig: 14

Fig: 15

Fig: 16

5. Install the LED kit by lifting both retention tabs upward. (Fig.15)

(Fig.16)

INSTALLATION

WITHOUT EXISTING FRAME (cont’d)

4. Install junction box cover plate. (Fig.14)

1. Use template inside box to cut hole in ceiling. (Fig.11)

Fig: 11

cable to a junction box with MC connector. Wire nut the

ground (green) wire in the junction box. Wire nut the black

input wire with the black wire from the MC cable and wire

nut the white input wire with the white wire from the MC

cable. Wire nut the purple input wire with the purple wire

from the MC cable and wire nut the pink input wire with

the pink wire from the MC cable. If the purple and pink

wires are not In use, cap these with wire nuts.(Fig.13)

Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.

Pink

INSTALLATION WITH EMERGENCY BATTERY BACKUP

Take the Emergency Battery Backup System and snap in the MC

cable from the EMBB into the J-Box. Fasten the LED retrot kit MC

cable to the J-Box. In the J-box, use wire nuts to do the wire

connections as illustrated in the diagram below. Make sure EMBB is

grounded. Please visit rablighting.com to view the emergency

battery backup compatibility list.