Page is loading ...
Pos: 2 /Dokumentation allgemein/Einband/Einband Handbuch - Fronts eite 20 15 - mit Doc Var iabl en ( Sta ndar d) @ 9\ mod_1285229289866_0.docx @ 64941 @ @ 1
WAGO-I/O-SYSTEM 750
Manual
750-451
8 AI RTD
8-
Channel Analog Input Module for Resistance
Sensors
Version 1.1.0
Pos: 3 /A lle Ser ien ( All ge mein e M odul e)/ Rec htlic h es, A llg emei nes /Im pre ssu m f ür St and ard han dbüc her - allg. Ang aben, A nschr iften, Telefo nnum mern un d E-Mail- Adres sen @ 3\mod_1219151118203_21.docx @ 21060 @ @ 1
2 WAGO-I/O-SYSTEM 750
750-451 8 AI RTD
Manual
Version 1.1.0
© 2016 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: +49 (0) 571/8 87 – 0
Fax: +49 (0) 571/8 87 – 1 69
Web: http://www.wago.com
Technical Support
Phone: +49 (0) 571/8 87 – 5 55
Fax: +49 (0) 571/8 87 – 85 55
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
=== Ende der Lis te f ür T e xtmar ke Ei nb and _vor ne = ==
WAGO-I/O-SYSTEM 750 Table of Contents 3
750-451 8 AI RTD
Manual
Version 1.1.0
Pos: 5 /D ok ument ati on al lg em ein/V erz eic hni sse /Inh alts ver zei chni s - Ü bersc hrift oG und Ver zeich nis @ 3\mod_1219151230875_21.docx @ 21063 @ @ 1
Table of Contents
1 Notes about this Documentation ................................................................. 6
1.1 Validity of this Documentation ................................................................. 6
1.2 Copyright ................................................................................................... 6
1.3 Symbols ..................................................................................................... 7
1.4 Number Notation ....................................................................................... 9
1.5 Font Conventions ...................................................................................... 9
2 Important Notes ......................................................................................... 10
2.1 Legal Bases ............................................................................................. 10
2.1.1 Subject to Changes ............................................................................. 10
2.1.2 Personnel Qualifications ..................................................................... 10
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions ........................................................................ 10
2.1.4 Technical Condition of Specified Devices ......................................... 11
2.2 Safety Advice (Precautions) .................................................................... 12
3 Device Description ..................................................................................... 14
3.1 View ........................................................................................................ 15
3.2 Connectors ............................................................................................... 16
3.2.1 Data Contacts/Internal Bus ................................................................. 16
3.2.2 Power Jumper Contacts/Field Supply ................................................ 17
3.2.3 Push-in CAGE CLAMP
®
Connectors ................................................ 18
3.3 Display Elements .................................................................................... 19
3.4 Operating Elements ................................................................................. 20
3.5 Schematic Diagram ................................................................................. 20
3.6 Technical Data ........................................................................................ 21
3.6.1 Device Data ........................................................................................ 21
3.6.2 Power Supply...................................................................................... 21
3.6.3 Communication .................................................................................. 21
3.6.4 Inputs .................................................................................................. 22
3.6.5 Measuring Accuracy at 25 °C ............................................................ 22
3.6.6 Connection Type ................................................................................ 23
3.6.7 Climatic Environmental Conditions ................................................... 23
3.7 Approvals ................................................................................................ 24
3.8 Standards and Guidelines ........................................................................ 25
4 Process Image ............................................................................................. 26
4.1 Overview ................................................................................................. 26
4.2 Control Bytes and Status Bytes ............................................................... 26
4.3 Process Data ............................................................................................ 28
4.3.1 Overview of Sensor Types ................................................................. 28
4.3.2 Pt100 (IEC 751), ID 0 ........................................................................ 29
4.3.2.1 Default Format ............................................................................... 29
4.3.2.2 S5-FB250 Format .......................................................................... 30
4.3.3 Ni100 (DIN 43760), ID 1 ................................................................... 31
4.3.3.1 Default Format ............................................................................... 31
4.3.3.2 S5-FB250 Format .......................................................................... 32
4.3.4 Pt1000 (IEC 751), ID 2 ...................................................................... 33
4 Table of Contents WAGO-I/O-SYSTEM 750
750-451 8 AI RTD
Manual
Version 1.1.0
4.3.4.1 Default Format ............................................................................... 33
4.3.4.2 S5-FB250 Format .......................................................................... 34
4.3.5 Pt500 (IEC 751), ID 3 ........................................................................ 35
4.3.5.1 Default Format ............................................................................... 35
4.3.5.2 S5-FB250 Format .......................................................................... 36
4.3.6 Pt200 (IEC 751), ID 4 ........................................................................ 37
4.3.6.1 Default Format ............................................................................... 37
4.3.6.2 S5-FB250 Format .......................................................................... 38
4.3.7 Ni1000 (TK6180, DIN 43760), ID 5 .................................................. 39
4.3.7.1 Default Format ............................................................................... 39
4.3.7.2 S5-FB250 Format .......................................................................... 40
4.3.8 Ni120 (Minco), ID 6 ........................................................................... 41
4.3.8.1 Default Format ............................................................................... 41
4.3.8.2 S5-FB250 Format .......................................................................... 42
4.3.9 Ni1000 (TK5000), ID 7 ...................................................................... 43
4.3.9.1 Default Format ............................................................................... 43
4.3.9.2 S5-FB250 Format .......................................................................... 44
4.3.10 Ni1000 (TK6180, DIN 43760), high-resolution, ID 8 ....................... 45
4.3.10.1 Default Format ............................................................................... 45
4.3.10.2 S5-FB250 Format .......................................................................... 46
4.3.11 Ni1000 (TK5000), high-resolution, ID 9 ........................................... 47
4.3.11.1 Default Format ............................................................................... 47
4.3.11.2 S5-FB250 Format .......................................................................... 48
4.3.12 Pt1000 (IEC 751), high-resolution, ID 10 .......................................... 49
4.3.12.1 Default Format ............................................................................... 49
4.3.12.2 S5-FB250 Format .......................................................................... 50
4.3.13 Resistance Measurement 1, 0 Ohm … 5.0 kOhm, ID 14 ................... 51
4.3.13.1 Default Format ............................................................................... 51
4.3.13.2 S5-FB250 Format .......................................................................... 52
4.3.14 Resistance Measurement 2, 0 Ohm … 1.2 kOhm, ID 15 ................... 52
4.3.14.1 Default Format ............................................................................... 52
4.3.14.2 S5-FB250 Format .......................................................................... 53
5 Mounting ..................................................................................................... 55
5.1 Mounting Sequence ................................................................................. 55
5.2 Inserting and Removing Devices ............................................................ 56
5.2.1 Inserting the I/O Module .................................................................... 56
5.2.2 Removing the I/O Module .................................................................. 57
6 Connect Devices ......................................................................................... 58
6.1 Connecting a Conductor to the Push-in CAGE CLAMP
®
...................... 58
6.2 Connection Examples .............................................................................. 59
6.2.1 8 × 2-wire ........................................................................................... 59
7 Commissioning ........................................................................................... 60
7.1 Parameterization via Register Communication ....................................... 60
7.1.1 Register Assignment ........................................................................... 62
7.1.2 Control and Status Bytes during Register Communication ................ 68
7.2 Parameterization with WAGO-I/O-CHECK ........................................... 69
7.2.1 Parameterization Dialog ..................................................................... 71
7.2.1.1 Toolbar ........................................................................................... 71
WAGO-I/O-SYSTEM 750 Table of Contents 5
750-451 8 AI RTD
Manual
Version 1.1.0
7.2.1.1.1 Main Menu ................................................................................ 72
7.2.1.1.2 Application Menu ..................................................................... 73
7.2.1.2 Navigation Area ............................................................................. 74
7.2.1.3 Application Area ............................................................................ 75
7.2.1.3.1 “Settings” Menu Item................................................................ 76
7.2.1.3.2 “Scaling” Menu Item ................................................................ 81
7.2.1.3.3 Application Examples of Scaling .............................................. 82
7.2.1.3.4 “Open Parameter File” Menu Item ........................................... 85
7.2.1.3.5 “Save Parameter File” Menu Item ............................................ 85
7.2.1.3.6 “Calibration” Menu Item .......................................................... 86
7.2.1.3.7 Application Example of Calibration ......................................... 87
7.2.1.4 Status Bar ....................................................................................... 89
7.3 Configuration and Parameterization using a GSD File with
PROFIBUS DP and PROFINET IO ....................................................... 90
8 Diagnostics .................................................................................................. 91
8.1 Error Response ........................................................................................ 91
9 Appendix ..................................................................................................... 93
9.1 Configuration and Parameterization using a GSD File with
PROFIBUS DP and PROFINET IO ....................................................... 93
9.1.1 Configuration 8 AI RTD .................................................................... 93
9.1.1.1 PROFIBUS DP (750-333, 750-833) Fieldbus Coupler
PROFINET IO (750-370) Fieldbus Coupler ................................. 93
9.1.1.2 PROFINET IO (750-375, 750-377) Fieldbus Coupler .................. 93
9.1.2 Parameterization 8 AI RTD ................................................................ 94
9.1.2.1 All PROFIBUS DP and PROFINET IO Fieldbus Couplers .......... 96
9.1.2.2 PROFIBUS DP (750-333, 750-833) Fieldbus Coupler ................. 97
9.1.2.3 PROFINET IO (750-370, 750-375, 750-377) Fieldbus Coupler ... 98
10 Use in Hazardous Environments ............................................................ 100
10.1 Marking Configuration Examples ......................................................... 101
10.1.1 Marking for Europe According to ATEX and IEC-Ex .................... 101
10.1.2 Marking for America According to NEC 500 .................................. 106
10.2 Installation Regulations ......................................................................... 107
10.2.1 Special Conditions for Safe Use (TÜV 14 ATEX 148929 X) ......... 108
10.2.2 Special Conditions for Safe Use (ATEX Certificate TÜV 12
ATEX 106032 X) ............................................................................. 109
10.2.3 Special Conditions for Safe Use (IEC-Ex Certificate
TUN
14.0035X) ......................................................................................... 110
10.2.4 Special Conditions for Safe Use (IEC-Ex Certificate IECEx
TUN 12.0039 X) ............................................................................... 111
10.2.5 Special Conditions for Safe Use according to ANSI/ISA 12.12.01 . 112
List of Figures .................................................................................................... 113
List of Tables ...................................................................................................... 114
=== Ende der Lis te f ür T e xtmar ke V erz eic hnis _vor ne == =
6 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-451 8 AI RTD
Manual
Version 1.1.0
Pos: 7 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten/ Ne ue Üb ers chr ift en/E ben e 1H in weise z u di eser D okum ent atio n - Ü bers chri ft 1 @ 4\mod_1237987661750_21.docx @ 29029 @ 1 @ 1
1 Notes about this Documentation
Pos: 8 /A lle Ser ien ( All ge mein e M odul e)/ Sic her heit s- und sonstige Hinweise/HinweisHinweis: Dokumentation aufbewahren @ 4\mod_1237987339812_21.docx @ 29026 @ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation is
included, if necessary.
Pos: 9 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten/ Ne ue Üb ers chr ift en/E ben e 2G ülti g keits ber eic h - Üb ersc hrif t 2 @ 1 2\mod_1338912448776_21.docx @ 96469 @ 2 @ 1
1.1 Validity of this Documentation
Pos: 10 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/G ülti gkei ts berei c h/Gül tig kei tsber ei ch D oku men tat ion Bus kle mme 75 0-xxxx, ohne Variantenangabe @ 14 \mod_1358944037947_21.docx @ 109346 @ @ 1
This documentation is only applicable to the I/O module 750-451
(8 AI RTD).
Pos: 11 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/Hi nw eise /Ac htu ng: H in weis zur D oku ment ati on B uskl e mmen 750- xxxx @ 4\mod_1237986979656_21.docx @ 29023 @ @ 1
The I/O module 750-451 shall only be installed and operated according to the
instructions in this manual and in the manual for the used fieldbus
coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
Pos: 12.1 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Ur heb ersc hut z - Ü bersc hr ift 2 @ 23\ mod_1435647042188_21.docx @ 184808 @ 2 @ 1
1.2 Copyright
Pos: 12.2 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Ur heb ersc hut z au sf ührli ch @ 4\mod_1235565145234_21.docx @ 27691 @ @ 1
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos: 12.3 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Notes about this Documentation 7
750-451 8 AI RTD
Manual
Version 1.1.0
Pos: 12.4 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/N eu e Ü bers chri fte n/E be ne 2 Sym bol e - Über sc hri ft 2 @ 1 3\mod_1351068042408_21.docx @ 105270 @ 2 @ 1
1.3 Symbols
Pos: 12 .5.1 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und so nsti ge H in weis e/G efa hr/G efa hr: _War nu ng vor P ers on ensc hä den allg emei n_ - Erl äuter ung @ 13\ mod_1343309450020_21.docx @ 101029 @ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12.5 .2 /A ll e Ser ien ( Al lg emei ne M od ule)/ Sic her heit s- u nd sons tige Hi nweis e/Gef ahr/G efahr : _War nung vor Person ensch äden d urch el ektris chen St rom_ - Erläuterung @ 13\mod_1343309694914_21.docx @ 101030 @ @ 1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12 .5.3 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und so nsti ge H in weis e/W arn ung/ War nung : _ War nu ng vor P ers one nsch äde n al lg emei n_ - Erläuterung @ 13\mod_1343309877041_21.docx @ 101035 @ @ 1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos: 12 .5.4 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonsti ge Hin weise/ Vorsic ht/V orsic ht: _War nung vor Pers one nschäd en allg emein _ - Erläuterung @ 13\mod_1343310028762_21.docx @ 101038 @ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos: 12 .5.5 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und so nsti ge H in weis e/A chtu ng/ Ach tung : _ War nung v or Sac hsc h äden allg em ein _ - Erläuterung @ 13\mod_1343310134623_21.docx @ 101041 @ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12 .5.6 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonstige Hinweis e/Acht ung/ Achtu ng: _War nung vor Sachs chäd en durc h elek trostat isch e Aufla dung_ - Erläut erung @ 13\mod_1343310227702_21.docx @ 101044 @ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12 .5.7 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonstige Hinweise/Hinweis/Hinweis: _Wichtiger Hinweis allgemein_ - Erläuterung @ 13\mod_1343310326906_21.docx @ 101047 @ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos: 12 .5.8 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und so nsti ge H in weis e/I nfor mat ion/ Inf or mati on: _W eiter e I nfor mat ion all ge mein_ - Erl äuter ung @ 13 \mod_1343310439814_21.docx @ 101051 @ @ 1
8 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-451 8 AI RTD
Manual
Version 1.1.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos: 12.6 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Notes about this Documentation 9
750-451 8 AI RTD
Manual
Version 1.1.0
Pos: 12.7 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Dar st ellu ng der Z ahl ens yst eme - Über sc hrift 2 @ 2 3\mod_1435647128078_21.docx @ 184811 @ 2 @ 1
1.4 Number Notation
Pos: 12.8 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Za hlens ys te me @ 3\mod_1221059454015_21.docx @ 21711 @ @ 1
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated with
dots (.)
Pos: 12.9 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Sc hri ftk on venti one n - Ü bersc hri ft 2 @ 23\mod_1435647186005_21.docx @ 184814 @ 2 @ 1
1.5 Font Conventions
Pos: 12.1 0 / Alle Ser ie n (All ge mein e M odul e) /Re chtl ich es, Allg em ein es/Sc hr ift konv enti onen @ 3\mod_1221059521437_21.docx @ 21714 @ @ 1
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.: Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]
Pos: 13 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
10 Important Notes WAGO-I/O-SYSTEM 750
750-451 8 AI RTD
Manual
Version 1.1.0
Pos: 14 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/N eue Ü ber schr if ten/ Ebe ne 1 Wic htig e Er lä uter ung en - Ü ber schr if t 1 @ 4\ mod_1241428899156_21.docx @ 32170 @ 1 @ 1
2 Important Notes
Pos: 15.1 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes Wic htig e Er läut eru nge n - Einl eitung @ 3\mod_1221059818031_21.docx @ 21717 @ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 15 .2 /All e Seri en (All ge meine Mo dul e)/Ü bers chr ift en/N eu e Ü bers chri fte n/E be ne 2R ec htlic he Gru ndlag en - Üb ersc hrif t 2 @ 3 \mod_1221060626343_21.docx @ 21726 @ 2 @ 1
2.1 Legal Bases
Pos: 15.3 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes Änd eru ngs vor beh alt - Ü ber schri ft 3 un d I nhalt @ 3\mod_1221060036484_21.docx @ 21720 @ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications that serve to increase the efficiency of technical
progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from
the granting of patents or from the legal protection of utility patents. Third-party
products are always mentioned without any reference to patent rights. Thus, the
existence of such rights cannot be excluded.
Pos: 15.4 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Pers onalq uali fikati onPer sonal qual ifika tion 750- xxxx - Ü bersc hrift 3 u nd Inhal t @ 3\mod_1224061208046_21.docx @ 24063 @ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos: 15.5 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Bestimmungsgemäße VerwendungBestimmungsgemäße Verwendung 750-xxxx - Über schrif t 3 und In halt @ 3\ mod_1224064151234_21.docx @ 24070 @ 3 @ 1
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions
Fieldbus couplers, fieldbus controllers and I/O modules found in the modular
WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and
transmit them to actuators or higher-level control systems. Using programmable
controllers, the signals can also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO-I/O-SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information
in the section “Device Description” > “Standards and Guidelines” in the manual
for the used fieldbus coupler/controller.
WAGO-I/O-SYSTEM 750 Important Notes 11
750-451 8 AI RTD
Manual
Version 1.1.0
Appropriate housing (per 2014/34/EU) is required when operating the WAGO-
I/O-SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
Pos: 15.6 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nesT ec hnis ch er Z ust and der G erä te - Über schr ift 3 und In halt @ 3\ mod_1221060446109_21.docx @ 21723 @ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. WAGO
Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of
changes in hardware or software as well as to non-compliant usage of devices.
Please send your request for modified and new hardware or software
configurations directly to WAGO Kontakttechnik GmbH & Co. KG.
Pos: 15.7 /Dokumentation allgemein/Glieder ungs elem ente /---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
12 Important Notes WAGO-I/O-SYSTEM 750
750-451 8 AI RTD
Manual
Version 1.1.0
Pos: 15.8 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/N eu e Ü bers chri fte n/E be ne 2 Sich er heits hi nweis e - Ü ber schr if t 2 @ 6\ mod_1260180299987_21.docx @ 46724 @ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 15.9 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äut eru nge n/Si cher hei ts hin weis e/Ei nl eitu ng Sich erh eitshi nweis e Hard ware @ 6\mod_1260180170493_21.docx @ 46720 @ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 15.1 0. 1 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : N ich t an G erät en unter Sp ann ung arbei te n! @ 6\mod_1260180365327_21.docx @ 46727 @ @ 1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: 15.1 0. 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en/ Sic herhei ts- und s o nstig e Hi nw eise /G efahr /Ge fahr : Ei nb au 0 750- xxx x nur in Ge häuse n, Schr änken o der el ektrisc hen Be triebs räu men! @ 6\mod_1260180556692_21.docx @ 46731 @ @ 1
Install the device only in appropriate housings, cabinets or in electrical
operation rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Pos: 15.1 0. 3 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : U nfal l verh ütung sv orsc hri ft en b each ten! @ 6\mod_1260180657000_21.docx @ 46735 @ @ 1
Pos: 15.1 0. 4 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : A uf normg er echt e n Ansc hlu ss ac hten! @ 6 \mod_1260180753479_21.docx @ 46739 @ @ 1
Pos: 15.1 1. 1 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Defek te oder besch ädigt e Gerät e aus taus ch en! @ 6 \mod_1260180857358_21.docx @ 46743 @ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Pos: 15.1 1. 2 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/Ac htung : Gerät e vor kri echen den und is olier end en Stoff en schüt zen! @ 6\mod_1260181036216_21.docx @ 46747 @ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for handling
devices/modules.
Pos: 15.1 1. 3 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Rei nig ung nur mi t zul äss ig en M at erial ien! @ 6\mod_1260181203293_21.docx @ 46751 @ @ 1
Clean only with permitted materials!
Clean soiled contacts using oil-free compressed air or with ethyl alcohol and
leather cloths.
Pos: 15.1 1. 4 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : K ein K ont a ktspra y verw end en! @ 6\ mod_1260181290808_21.docx @ 46755 @ @ 1
WAGO-I/O-SYSTEM 750 Important Notes 13
750-451 8 AI RTD
Manual
Version 1.1.0
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos: 15.1 1. 5 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : V erpol ung ver mei de n! @ 6\mod_1260184045744_21.docx @ 46767 @ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos: 15.1 1. 6 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Elektr ostat isch e Entla dung v ermeid en! @ 6\ mod_1260181364729_21.docx @ 46759 @ @ 1
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
Pos: 16 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
14 Device Description WAGO-I/O-SYSTEM 750
750-451 8 AI RTD
Manual
Version 1.1.0
Pos: 17.1 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/N eu e Ü bers chri fte n/E be ne 1 Ger äteb esc hrei bung - Ü bers chri ft 1 @ 3\mod_1233756084656_21.docx @ 27096 @ 1 @ 1
3 Device Description
Pos: 17.2 .1 /Ser ie 7 50 ( WAG O-I/ O-SYSTEM)/Gerätebeschreibung/Einleitung/Anwendung/AI/Anwendung 750-04x x AI RT D p ar ametr i erbar @ 10\mod_1313576749855_21.docx @ 77170 @ @ 1
The I/O module 750-451 (8 AI RTD) measures resistance at field level or
evaluates platinum or nickel resistance sensors.
The resistance values are converted into temperature values. A microprocessor in
the I/O module linearizes the measured resistance values and converts them into a
numeric value proportional to the temperature of the selected resistance sensor.
The WAGO-I/O-CHECK commissioning tool can be used to set the required
operating mode.
Pos: 17.2 .2 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/I/ O-B esc hrei bung /AI/I /O- Besc hreib ung 750- 04x x 8 A I RT D P ush-i n C AGE C LAM P @ 1 6\mod_1375368716345_21.docx @ 127583 @ @ 1
The I/O module has eight input channels, providing a direct connection to 2-wire
resistance sensors.
The sensors are connected to Push-in CAGE CLAMP
®
terminals +A1/−A1 ...
+A8/−A8.
Pos: 17.2 .3 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/I/ O-B esc hrei bung /All ge mein /V er weis a uf Kapi tel " A nsc hlüss e" @ 8\ mod_1276775378035_21.docx @ 57956 @ @ 1
The assignment of the connections is described in the “Connectors” section.
Pos: 17.2 .4 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/I/ O-B esc hrei bung /All ge mein /V er weis a uf Kapi tel " G erät e an schl ieß en" > " Ansc hl ussb eis piel (e) " @ 5\mod_1246015203281_21.docx @ 36298 @ @ 1
Connection examples are shown in section “Connecting Devices” > … >
“Connection Example(s)”.
Pos: 17.2 .5 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/L ED-A nzeig e/LED Zustan d Betr ieb Kanal @ 5\mod_1245391732046_21.docx @ 35668 @ @ 1
The operating status of the channels is indicated by a green status LED per
channel.
Pos: 17.2 .6 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/L ED-A nz eige/ LED Fe hler Kur zsc hlus s/D ra htbr uch/ B ereic hsü ber -/unt ersc hreit ung @ 5\mod_1245391942765_21.docx @ 35672 @ @ 1
A red error LED per channel indicates a wire break, a short circuit or that the
signal is outside the measuring range.
Pos: 17.2 .7 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/L ED-A nzeig e/Ver weis au f Kapit el "Anz eige elemen te" @ 5\mod_1246010525000_21.docx @ 36194 @ @ 1
The meaning of the LEDs is described in the “Display Elements” section.
Pos: 17.2 .8 /Ser ie 7 50 ( WAG O-I/ O-SYSTEM)/Wichtige Erläuterungen/Sicherheits- und sonstige Hinweise/Achtung/Achtung: Maximaler Strom Leistungskontakte 10 A @ 3\mod_1226499143500_21.docx @ 25029 @ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos: 17.2 .9 /Ser ie 7 50 ( WAG O-I/ O-SYST EM)/ Wichtig e Erlä uteru nge n/Sic her heit s- u nd so nsti ge Hin weis e/H inw eis/H i nwei s: Pote nti alei ns peis ekl emm e für Erd e ei ns etze n! ( kei ne L K f ür Erde) @ 3\mod_1226499037468_21.docx @ 25023 @ @ 1
Use supply modules for ground (earth)!
The I/O module has no power jumper contacts for receiving and transmitting the
earth potential. Use a supply module when an earth potential is needed for the
subsequent I/O modules.
Pos: 17.2 .1 0 /S erie 750 ( W AGO -I/O-SY STEM )/Ger ätebe schr eibung /Einl eitung /V ersorg ung/A nord nung unt er Ber ücksic htigu ng der L eistungs kontakte beliebig @ 3\mod_1233756233468_21.docx @ 27099 @ @ 1
With consideration of the power jumper contacts, the individual modules can be
arranged in any combination when configuring the fieldbus node. An arrangement
in groups within the group of potentials is not necessary.
Pos: 17.2 .1 1 /S erie 750 ( W AGO -I/O-SY STEM )/Ger ätebe schr eibung /Einl eitung /Ein satzb ereic h/Ein satzb ereic h 750- xxxx all e Ko ppler /C ontr oll er o hne Ei nsc hrä nkung @ 3 \mod_1232541691906_21.docx @ 26522 @ @ 1
The I/O module 750-451 can be used with all fieldbus couplers/controllers of the
WAGO-I/O-SYSTEM 750.
Pos: 17.3 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /Ei nlei tu ng/V ers org ung/ Gal va nisch e Tr en nung Fel d/S yst em @ 3\ mod_1233756478750_21.docx @ 27102 @ @ 1
The field voltage and the system voltage are electrically isolated from each other.
Pos: 17.4 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Device Description 15
750-451 8 AI RTD
Manual
Version 1.1.0
Pos: 17.5 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/N eu e Ü bers chri fte n/E be ne 2 Ansi cht - Über sc hrift 2 @ 4\ mod_1240984217343_21.docx @ 31958 @ 2 @ 1
3.1 View
Pos: 17.6 /Serie 750 (WAGO-I/O-SYST EM)/ Ger ätebesc hrei bung/A nsic ht/A nalogei ngang skl emmen/ Ansi cht 750- 0451 - Abb. @ 16\ mod_1375369749979_21.docx @ 127590 @ @ 1
Figure 1: View
Pos: 17.7 /Serie 750 (WAGO-I/O-SYST EM)/ Ger ätebesc hrei bung/A nsic ht/A nsicht P ush-in Cag eCla mp®_L egend e mit LED s @ 15\mod_1370852562803_21.docx @ 122213 @ @ 1
Table 3: Legend for Figure “View”
Pos.
Description
Details See Section
1
Marking possibility with
Mini-WSB
---
2
Status LEDs
“Device Description” > “Display Elements”
3
Data contacts
“Device Description” > “Connectors”
4
Push-in CAGE CLAMP
®
connectors
“Device Description” > “Connectors”
5
Power jumper contacts
“Device Description” > “Connectors”
6
Release tab
“Mounting” > “Inserting and Removing
Devices”
Pos: 17.8 /Dokumentation allgemein/Gliederungselemente/---Seiten wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
16 Device Description WAGO-I/O-SYSTEM 750
750-451 8 AI RTD
Manual
Version 1.1.0
Pos: 17.9 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/N eu e Ü bers chri fte n/E be ne 2 Ansc hlüs se - Ü b ersc hrif t 2 @ 4 \mod_1240984262656_21.docx @ 31961 @ 2 @ 1
3.2 Connectors
Pos: 17.1 0 / Ser ie 7 50 ( WAG O-I/ O-SYST EM) /Ger äte besc hrei bu ng/A nsc hlüss e/D ate nkont akt e/Kl emm enb us - Üb ersc hrift 3 @ 6\ mod_1256294684083_21.docx @ 43660 @ 3 @ 1
3.2.1 Data Contacts/Internal Bus
Pos: 17.1 1. 1 /S erie 750 ( W AGO -I/O-SY ST EM)/G erät ebe schr eib ung/ Ansc hlüs se/D at enko nta kte - F eldb usk oppl er/-c ontr oller, Abbil dung un d Beschr eibung @ 3\mod_1231771259187_21.docx @ 26002 @ @ 1
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the internal bus. It
is comprised of 6 data contacts, which are available as self-cleaning gold spring
contacts.
Figure 2: Data Contacts
Pos: 17.1 1. 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/A cht ung /Ac htung : Bus kle mme n nic ht auf G ol dfed er kont akt e leg en! @ 7\mod_1266318463636_21.docx @ 50695 @ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos: 17.1 1. 3 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/A cht ung /Ac htung : ESD - Auf gute Erdung der Umgebung achten! @ 7\mod_1266318538667_21.docx @ 50708 @ @ 1
Ensure that the environment is well grounded!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, ensure that the environment
(persons, workplace and packing) is well grounded. Avoid touching conductive
components, e.g. data contacts.
Pos: 17.1 2 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Device Description 17
750-451 8 AI RTD
Manual
Version 1.1.0
Pos: 17.1 3 / Ser ie 7 50 ( WAG O-I/ O-SYST EM) /Ger äte besc hrei bu ng/A nsc hlüss e/L eist ungs ko ntakt e/F eldv ers orgung - Ü bers chrif t 3 @ 6 \mod_1256294692864_21.docx @ 43664 @ 3 @ 1
3.2.2 Power Jumper Contacts/Field Supply
Pos: 17.1 4. 1 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/V ors ich t/V orsic ht: Ver let zu ngsg efa hr d urc h sc har fka ntige Mes ser kon takte! @ 6\mod_1256193279401_21.docx @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
Pos: 17.1 4. 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Ger äte bes chr eib ung/ Ans chl üss e/L eist ungs kon tak te 2 LK ( M esser /Lei st ung sko nta kte 2 LK (Mes ser /F eder ) - E inl eitu ng @ 15\ mod_1371721641099_21.docx @ 123714 @ @ 1
The I/O module 750-451 has 2 self-cleaning power jumper contacts that supply
and transmit power for the field side. The contacts on the left side of the I/O
module are designed as blade contacts and those on the right side as spring
contacts.
Pos: 17.1 4. 3 /S erie 750 ( W AGO -I/O-SY ST EM) /Ger äte bes chr eib ung/ Ans chl üss e/L eist ungs kon tak te 2 LK ( M esser /Fe der ) - Abbildung (16-Kanal) @ 15\mod_1370866610582_21.docx @ 122222 @ @ 1
Figure 3: Power Jumper Contacts
Pos: 17.1 4. 4 /S erie 750 ( W AGO -I/O-SY ST EM) /Ger äte bes chr eib ung/ Ans chl üss e/L eist ungs kon tak te 2 LK ( M esser /Lei st ung sko nta kte 2 LK (Mes ser /F eder ) - Leg en de @ 1 5\mod_1371721352500_21.docx @ 123710 @ @ 1
Table 4: Legend for Figure “Power Jumper Contacts”
Contact
Type
Function
1
Spring contact
Potential transmission (U
v
) for field supply
2
Spring contact
Potential transmission (0 V) for field supply
3
Blade contact
Potential feed-in (0 V) for field supply
4
Blade contact
Potential feed-in (U
v
) for field supply
Pos: 17.1 4. 5 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/A cht ung /Ac htung : Maxi maler Stro m Leistu ngsko ntakt e 10 A @ 3\mod_1226499143500_21.docx @ 25029 @ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos: 17 .15 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1
18 Device Description WAGO-I/O-SYSTEM 750
750-451 8 AI RTD
Manual
Version 1.1.0
Pos: 17.1 6 / Ser ie 7 50 ( WAG O-I/ O-SYST EM) /Ger äte besc hrei bu ng/A nsc hlüss e/P ush-i n C AGE C LAM P®-A nsc hlüss e - Üb ersc hrift 3 @ 15 \mod_1370519905692_21.docx @ 122018 @ 3 @ 1
3.2.3 Push-in CAGE CLAMP
®
Connectors
Pos: 17.1 7 / Ser ie 7 50 ( WAG O-I/ O-SYST EM)/ Gerät ebesc hreib ung/ Ansc hlüsse/ Anal ogeing angs klem men/A nschl üsse 7 50-0451 @ 16\mod_1375370431718_21.docx @ 127593 @ @ 1
Figure 4: Push-in CAGE CLAMP
®
Connectors
Table 5: Legend for Figure “Push-in CAGE CLAMP
®
Connectors” – 8-Channel, 2-Wire
Channel
Designation
Connector
Function
1
+AI1
1
Sensor 1: +R
−AI1
2
Sensor 1: −R
2
+AI2
3
Sensor 2: +R
−AI2
4
Sensor 2: −R
3
+AI3
5
Sensor 3: +R
−AI3
6
Sensor 3: −R
4
+AI4
7
Sensor 4: +R
−AI4
8
Sensor 4: −R
5
+AI5
9
Sensor 5: +R
−AI5
10
Sensor 5: −R
6
+AI6
11
Sensor 6: +R
−AI6
12
Sensor 6: −R
7
+AI7
13
Sensor 7: +R
−AI7
14
Sensor 7: −R
8
+AI8
15
Sensor 8: +R
−AI8
16
Sensor 8: −R
Pos: 17.1 8 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Device Description 19
750-451 8 AI RTD
Manual
Version 1.1.0
Pos: 17.1 9 / Alle Ser ie n (All ge mein e M odul e) /Üb ersc hri ften /Ne ue Ü bers chr ift en/E b ene 2Anz eig eele men te - Über schr ift 2 @ 4\mod_1240984390875_21.docx @ 31964 @ 2 @ 1
3.3 Display Elements
Pos: 17.2 0 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung /A nzeig eel eme nte/ An alog eing ang s kle mmen/ Anz eig eele me nte 7 50- 0451 @ 16\mod_1375370815748_21.docx @ 127596 @ @ 1
Figure 5: Display Elements
Pos: 17.2 1 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1
Table 6: Legend for Figure “Display Elements”
Chan-
nel
Desig-
nation
LED State Function
1
R1 status 1
OFF
Not ready for operation or no or disturbed
internal bus communication, channel
disabled
Green
Ready for operation and undisturbed
internal bus communication
R1 error 9
OFF
No error and/or diagnostics disabled or
channel disabled
Red
Permissible measuring range overrange
and underrange, short circuit, wire break
2
R2 status
2
(see channel 1)
R2 error
10
(see channel 1)
3
R3 status
3
(see channel 1)
R3 error
11
(see channel 1)
4
R4 status
4
(see channel 1)
R4 error
12
(see channel 1)
5
R5 status
5
(see channel 1)
R5 error
13
(see channel 1)
6
R6 status
6
(see channel 1)
R6 error
14
(see channel 1)
7
R7 status
7
(see channel 1)
R7 error
15
(see channel 1)
8
R8 status
8
(see channel 1)
R8 error
16
(see channel 1)
20 Device Description WAGO-I/O-SYSTEM 750
750-451 8 AI RTD
Manual
Version 1.1.0
Pos: 17.2 2 / Alle Ser ie n (All ge mein e M odul e) /Üb ersc hri ften /Ne ue Ü bers chr ifte n/Eb ene 2Be dienel ement e - Über schri ft 2 @ 4\mod_1239191655456_21.docx @ 30439 @ 2 @ 1
3.4 Operating Elements
Pos: 17.2 3 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung /B edien el eme nte/ Bedi en ele ment e B uskl emm e 7 50-xxxx nich t vorhanden @ 4\mod_1236322031125_21.docx @ 28063 @ @ 1
The I/O module 750-451 has no operating elements.
Pos: 17.2 4 / Alle Ser ie n (All ge mein e M odul e) /Üb ersc hri ften /Ne ue Ü bers chr ift en/E b ene 2Sch ema tisc hes Sc halt bil d - Ü ber schri ft 2 @ 4\mod_1240984441312_21.docx @ 31967 @ 2 @ 1
3.5 Schematic Diagram
Pos: 17.2 5 / Ser ie 7 50 ( WAG O-I/ O-SYST EM)/ Gerät ebesc hreib ung/ Schem atisc he Schal tbild er/A nalog einga ngskle mme n/Sch emati sches Schalt bild 75 0-0451 @ 16\mod_1375373040581_21.docx @ 127602 @ @ 1
Figure 6: Schematic Diagram
Pos: 17.2 6 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1
/
