Metra 107-FD1B Installation guide

Category
Car kits
Type
Installation guide

This manual is also suitable for

Metra 107-FD1B is a car radio installation kit designed for the Ford Transit, excluding factory radio delete models. It allows for the installation of an ISO DDIN radio or a Pioneer modular 6.8” radio. The kit includes a radio trim panel, radio housing, sub-dash brackets, radio brackets, panel clips, and screws. With this kit, you can easily upgrade your vehicle's audio system by adding a new radio that fits seamlessly into the dashboard.

Metra 107-FD1B is a car radio installation kit designed for the Ford Transit, excluding factory radio delete models. It allows for the installation of an ISO DDIN radio or a Pioneer modular 6.8” radio. The kit includes a radio trim panel, radio housing, sub-dash brackets, radio brackets, panel clips, and screws. With this kit, you can easily upgrade your vehicle's audio system by adding a new radio that fits seamlessly into the dashboard.

Metra. The World’s Best Kits.
®
MetraOnline.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 12/11/20 INST107-FD1B
INSTALLATION INSTRUCTIONS
107-FD1B
Patent Pending
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
KIT COMPONENTS
A) Radio trim panel • B) Radio housing • C) Sub dash brackets • D) Radio brackets • E) Panel clips (3) • F) #8 x 1/2” Phillips screws (4)
TOOLS REQUIRED
• Panel removal tool • 9/32” socket
• Phillips screwdriver • Cutting tool
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation .......................................................3
Kit Assembly
–ISO DDIN radio provision .....................................4
–Pioneer Modular radio provision .......................5
WIRING & ANTENNA CONNECTIONS
(sold separately)
See metra-online.com or axxessinterfaces.com
for audio and SWC interface options
Antenna Adapter: 40-EU10
A C D E
F
B
Ford Transit (excludes factory radio delete models) 2020
Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle
specific applications
KIT FEATURES
ISO DDIN radio provision*
Painted scratch resistant matte black
* This kit is designed for an ISO DDIN radio which have an “L” shaped chassis
design, with the radio chassis at the bottom of the screen,
or Pioneer modular 6.8” radios.
† Refer to the radio manufacturer for current models
1.800.221.0932
|
MetraOnline.com
2
DASH DISASSEMBLY
(Figure A) (Figure D)
(Figure B) (Figure E)
(Figure C)
1. Unclip the trim behind the radio display,
then remove (3) 9/32” screws exposed.
(Figure A)
2. Slide the radio display up and out, then
unplug and remove. (Figure B)
3. Remove (2) screws securing the center
dash panel, then unclip, unplug, and
remove. (Figure C)
4. Remove (4) 9/32” screws securing the
radio display mount, then remove.
(Figure D)
5. Unplug the connectors from the radio
chassis. Remove (2) 9/32” screws
securing the chassis, slide out, then
remove. (Figure E)
Continue to Kit Preparation
REV. 12/11/2020 INST107-FD1B
3
(Figure B)(Figure A)
KIT PREPARATION
1. Attach the (3) included panel clips to the
radio trim panel. (Figure A)
2. Cut and remove the two lower mounting
tabs from the inside of the factory dash
panel radio opening. (Figure B)
Continue to Kit Assembly
Remove shaded areas
1.800.221.0932
|
MetraOnline.com
4
KIT ASSEMBLY
Bottom chassis radio provision
1. Secure the sub-dash brackets to the
dash using the factory screws. (Figure A)
2. Snap off the front of the radio brackets
and secure them to the radio using
screws supplied with the radio.
(Figure B, C)
3. Snap the radio housing into the factory
dash panel. (Figure D)
4. Snap the factory dash panel back
in place.
5. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using
the proper mating adapter from Metra
and/or Axxess. Test the radio for proper
operation.
6. Slide the radio assembly into to the dash
and secure to the radio housing using
the (4) included Phillips screws.
(Figure E)
7. Snap the radio trim panel into the
radio housing. (Figure F)
(Figure A) (Figure D)
(Figure B) (Figure E)
(Figure C) (Figure F)
Remove shaded areas
REV. 12/11/2020 INST107-FD1B
5
Pioneer Modular DDIN radio provision
Note: For steps 2 and 3, reference the
installation manual provided with the radio
for which hardware to use. The display
screen and radio chassis use two different
types of screws.
1. Secure the sub-dash brackets to the
dash using the factory screws. (Figure A)
2. Secure the radio brackets to the radio
display using (4) screws supplied with
the radio. (Figure B)
3. Secure the radio brackets to the radio
chassis using (4) screws supplied with
the radio. (Figure C)
4. Snap the radio housing into the factory
dash panel. (Figure D)
5. Snap the factory dash panel back in
place.
6. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using
the proper mating adapter from Metra
and/or Axxess. Test the radio for proper
operation.
7. Slide the radio assembly into to the dash
and secure to the radio housing using
the (4) included Phillips screws.
(Figure E)
8. Snap the radio trim panel into the
radio housing. (Figure F)
KIT ASSEMBLY
(Figure D)
(Figure B) (Figure E)
(Figure C) (Figure F)
(Figure A)
1.800.221.0932
|
MetraOnline.com
6
REV. 12/11/2020 INST107-FD1B
7
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
Metra recommends MECP
certified technicians
Metra. The World’s Best Kits.
®
MetraOnline.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 12/11/20 INST107-FD1B
INSTALLATION INSTRUCTIONS
107-FD1B
Having difficulties? We’re here to help.
Contact our Tech Support line at:
386-257-1187
Or via email at:
techsupport@metra-autosound.com
Tech Support Hours (Eastern Standard Time)
Monday - Friday: 9:00 AM - 7:00 PM
Saturday: 10:00 AM - 7:00 PM
Sunday: 10:00 AM - 4:00 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Metra 107-FD1B Installation guide

Category
Car kits
Type
Installation guide
This manual is also suitable for

Metra 107-FD1B is a car radio installation kit designed for the Ford Transit, excluding factory radio delete models. It allows for the installation of an ISO DDIN radio or a Pioneer modular 6.8” radio. The kit includes a radio trim panel, radio housing, sub-dash brackets, radio brackets, panel clips, and screws. With this kit, you can easily upgrade your vehicle's audio system by adding a new radio that fits seamlessly into the dashboard.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI