Metra 107-CH5 Operating instructions

Category
Car kits
Type
Operating instructions

Metra 107-CH5 is a car installation kit, designed for Jeep Grand Cherokee 1996-1998 models. It enables the installation of an ISO DDIN radio or a Pioneer Modular 6.8" radio. The kit includes a radio trim panel, radio brackets, an extension bracket, a vent adapter, and mounting hardware. It features a textured finish to match the factory dash and provides a sleek and integrated look. This kit streamlines the installation process and ensures a secure and professional fit for your new radio system.

Metra 107-CH5 is a car installation kit, designed for Jeep Grand Cherokee 1996-1998 models. It enables the installation of an ISO DDIN radio or a Pioneer Modular 6.8" radio. The kit includes a radio trim panel, radio brackets, an extension bracket, a vent adapter, and mounting hardware. It features a textured finish to match the factory dash and provides a sleek and integrated look. This kit streamlines the installation process and ensures a secure and professional fit for your new radio system.

Metra. The World’s Best Kits.
®
MetraOnline.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 11/10/20 INST107-CH5
INSTALLATION INSTRUCTIONS
107-CH5
Patent Pending
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
KIT FEATURES
ISO DDIN radio provision*
Textured to match the factory finish
* This kit is designed for an ISO DDIN radio which have an “L” shaped chassis
design, with the radio chassis at the top of the screen,
or Pioneer modular 6.8” radios.
† Refer to the radio manufacturer for current models
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) Extension bracket • D) Vent adapter • E) #8 x 1/2” screw for drivers side (1)
TOOLS REQUIRED
• 3/8” socket set • Cutting tool/Dremel
• Panel removal tool • Phillips screwdriver
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation .......................................................3
Kit Assembly
–ISO DDIN radio provision .....................................4
–Pioneer Modular radio provision .......................5
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: 70-1817
Antenna Adapter: Not required
A CB D E
Jeep Grand Cherokee 1996-1998
Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle
specific applications
1.800.221.0932
|
MetraOnline.com
2
1. Unsnap the climate control/wiper control
trim panel and remove. (Figure A)
2. Unsnap the headlight switch trim panel
and remove. (Figure B)
3. Remove (10) Phillips screws from the
top and bottom of the radio/instrument
cluster trim bezel. Pry out on the bottom
edge of the bezel and remove. (Figure C)
4. Remove (2) 3/8” hexhead screws
securing the factory radio and
disconnect the wiring.
Continue to Kit Preparation
DASH DISASSEMBLY
(Figure A) (Figure B) (Figure C)
REV. 11/10/2020 INST107-CH5
3
(Figure D)
(Figure E) (Figure G)
(Figure F)
KIT PREPARATION
1. Cut and remove the climate vents from
the factory dash panel. (Figure A)
2. Cut the vent area of the factory dash
panel. (Figure B)
3. Secure the extension bracket into the
driver’s side of the dash opening and
secure using factory hardware. (Note the
grabbing clip at the back of the bracket)
(Figure C)
4. Place the vent extension into the factory
vent opening. (Figure D)
Continue to Kit Assembly
Remove shaded area
Remove shaded area
1.800.221.0932
|
MetraOnline.com
4
(Figure A) (Figure B)
KIT ASSEMBLY
Chassis Top DDIN radio provision
1. Snap the front mounting tabs off of the
radio brackets. (Figure A)
2. Secure the radio brackets to the radio
using screws supplied with the radio.
(Figure B)
3. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using
the proper mating adapter from Metra
and/or Axxess. Test the radio for proper
operation.
4. Slide the radio assembly into to the
dash, then secure using the factory
hardware for the passenger side and
(1) #8 Phillips head screw for the
driver’s side.
5. Clip the radio trim panel to the factory
dash panel.
6. Reassemble the dash in reverse
order of disassembly to complete the
installation.
Remove tabs
REV. 11/10/2020 INST107-CH5
5
KIT ASSEMBLY
Pioneer Modular radio provision
Note: For steps 1 and 2, reference the
installation manual provided with the radio
for which hardware to use. The display
screen and radio chassis use two different
types of screws.
1. Secure the radio brackets to the radio
chassis using (4) screws supplied with
the radio. (Figure A)
2. Secure the radio display to the radio
brackets using (4) screws supplied with
the radio. (Figure B)
3. Connect the radio display to the
radio chassis.
4. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using
the proper mating adapter from Metra
and/or Axxess. Test the radio for proper
operation.
5. Slide the radio assembly into to the dash,
then secure using the factory hardware
for the passenger side and (1) #8 Phillips
head screw for the driver’s side.
6. Clip the radio trim panel to the factory
dash panel.
7. Reassemble the dash in reverse order of
disassembly to complete the installation.
(Figure A)
(Figure B)
1.800.221.0932
|
MetraOnline.com
6
REV. 11/10/2020 INST107-CH5
7
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
Metra recommends MECP
certified technicians
Metra. The World’s Best Kits.
®
MetraOnline.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 11/10/20 INST107-CH5
INSTALLATION INSTRUCTIONS
107-CH5
Having difficulties? We’re here to help.
Contact our Tech Support line at:
386-257-1187
Or via email at:
techsupport@metra-autosound.com
Tech Support Hours (Eastern Standard Time)
Monday - Friday: 9:00 AM - 7:00 PM
Saturday: 10:00 AM - 7:00 PM
Sunday: 10:00 AM - 4:00 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Metra 107-CH5 Operating instructions

Category
Car kits
Type
Operating instructions

Metra 107-CH5 is a car installation kit, designed for Jeep Grand Cherokee 1996-1998 models. It enables the installation of an ISO DDIN radio or a Pioneer Modular 6.8" radio. The kit includes a radio trim panel, radio brackets, an extension bracket, a vent adapter, and mounting hardware. It features a textured finish to match the factory dash and provides a sleek and integrated look. This kit streamlines the installation process and ensures a secure and professional fit for your new radio system.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI