Hanover HANGRNHS4X6-NAT Installation guide

Brand: Hanover

Model: HANGRNHS4X6-NAT

Type: Installation guide

Hanover HANGRNHS4X6-NAT is a greenhouse with metal base. Here is some brief information about the product:

Overall size: 130 cm x 190 cm x 195 cm (51" x 75" x 76.7")
Door is hinged on the right-hand side
Easy to assemble
Can be fixed on a solid concrete foundation with pre-drilled holes
Do not position your greenhouse in an area exposed to excessive wind

Hanover HANGRNHS4X6-NAT is a greenhouse with metal base. Here is some brief information about the product:

Overall size: 130 cm x 190 cm x 195 cm (51" x 75" x 76.7")
Door is hinged on the right-hand side
Easy to assemble
Can be fixed on a solid concrete foundation with pre-drilled holes
Do not position your greenhouse in an area exposed to excessive wind

You must read these instructions carefully before you start to assemble it.

Overall Size/inch: L51"x W75"x H76.7"

Overall Size/CM: L130 x W190 x H195

Assembly Instruction

Metal Base of Greenhouse

the assembly of the whole product.

quantity as mentioned in the list.

Do not tighten the steps until completing on

IMPORTANT

Please ensure that you find all parts in the correct type and

Please carry out the steps according to the instructions.

Keep the instruction manuals in a safe place for future reference.

9820102-1

9820102-2



IMPORTANT

Ifyouhaveanyproblemswiththisproduct, please 

DONOTRETURNTHISITEM

theRetailer/Storefromwhereyoupurchasedtheproduct.



Pleaseemailusanytimewiththenatureoftheproblemat:

ContactUs@Hanover‐Products.com

Pleaseinclude:

 Picturesoftheissue(s)andreceipt

(ifavailable)

 NameandaddressofthePurchaser

 Nameofretailer



OrcallourCustomer

Serviceteambetween9:00AM

and5:00PMEasternTime,

MondaythroughFridayat:

1‐877‐397‐5144



orvisitourwebsiteat:

www.Hanover‐Products.com



Toexpediteanyfuturewarranty

claims,pleaseretainyourreceiptforfutureuse. 



Foradditionalon‐linesupportonassembly,troubleshooting

and

care&maintenanceofyouroutdoor

product,pleasevisitourwebsiteat:www.Hanover

‐Products.com.



8/1/2019



When your greenhouse need cleaning, use a mild detergent solution and risen with cool clean water.

Note that the door is hinged on the right hand side and therefore opens to the right side.

Hot items such as recently used grills, blowtorches must not be stores in the

Dispose of all plastic bags safely. Keep them out of reach of small children.

Do NOT use acetone, abrasive cleaners or other special detergent to clean the panels.

This is a multi-part assembly and needs at least 3-4 hours for assembly.

SAFETY ADVICE

We strongly recommend the use of work gloves during assembly.

Do not attempt to assemble the greenhouse in windy or wet conditions,

Do not touch overhead power cables with the aluminum profiles.

Always wear shoes and safety goggles when working with extruded aluminum.

The greenhouse must be positioned and fixed on a flat level surface.

Do not lean against or push the greenhouse during construction.

Keep children away from the assemble area.

Do not position your greenhouse in an area exposed to excessive wind.

Do not attempt to assemble this greenhouse if you are tired ,have taken drugs or

alcohol

or if you are prone to dizzy spells.

If using a step ladder or power tools ensure that you follow the manufactures safety

advice.

greenhouse.

Ensure there are no hidden pipes or cables in the ground before inserting the pegs.

GENERAL ADVICE

Selecting a site-choose a sunny level position away from overhanging trees.

If you are fixing your greenhouse directly to a solid concrete foundation use the pre

drilled holes in the metal base supplied.

The component parts should be checked and laid out close at hand.

Keep all small parts (screws etc)in a bowl so they do not get lost.

Keep roof clear of snow and leaves.

CARE & MAINTENANCE

1.Tape (10feet)

TOOLS

&EQUIPMENT REQUIRED

Protective Equipment:

1.Helmet

2.Glove

3.Long Sleeve Cotton Overalls

4.Emergency Medicine Cabinet

5.Eye Shield

Measure (metric):

2.Angle Square

3.Level Meter

Silicon

8.Percussion bit (10mm) (25/64)

7.Marking Pen

6.Wooden Mallet

5mm (13/64) inch hexagon wrench

5.Electric screwdriver +

4.Hexagon wrench 5mm (13/64) inch

1.Triangle Stair 5 feet height

2.Spanner 10mm / (25/64) (Ratchet Wrench is better)

3.Spanner 14mm / (35/64) (Install the expansion screw)

10.Phillips screwdriver

9.Knife

Advised Installation Tools:

PART LIST

Do not fully-tighten screws

Door Assembly

Note: Lay the door frame on a flat surface.

Make sure that door is square and even

before tightening screws.

Note: Make sure that the window is flat and even

before rightening all screws.

Window Installation

Window supporting knob

Pre-place F4 screws in below parts and quantity,

Screw Preparation

Note:the two 7# parts close to 10R/L

screws pre-placed in previous step.

Fix the parts 10R and 10L with the F4

Pre-place 1 piece F4 screws in parts 10R,10L

part 4,5 and 6.

with pre-placed F4 screws in

Frame Installation

Fix the frame at each corner

should be placed 3 pieces screws.There

are 2 pieces groove in part 7#, and

you need to pre-place 2 pieces F4 screws

in one groove towards to 10R/L and 1

piece F4 screw in the other groove.

14# part should be installed

12# and 15# parts are short parts,

covering on the top of PC panels;

to panels P3-P5-P3.

Back Wall Installation

1.Attach panels P3-P5-P3

to base with S2.

2.Attach rails 12-15-12

3.Attach panels P4R-P6-P4L

to rails 12-15-12.

Pre-place 2 pieces F4 screws

into each part 12# and 15#.

Fix the beam of back wall 14#

with the pre-placed F4 screws

at previous step in parts

7#,10L,10R,12# and 15#.

14# part is a long part across

the whole width of greenhouse.

on 10L/R and 7#.

Parts 12# and 15# are fixed on

the part 14# with the pre-placed

screws F4.

Fix the parts 9# with the F4

Note:the other two 7# parts should be

in one groove towards to 9 and 1

you need to pre-place 3 pieces F4 screws

pieces groove in part 7#, and

placed 4 pieces screws.There are 2

Front Wall Installation

piece F4 screw in the other groove.

screws pre-placed in previous step.

Fix part 13 with pre-placed

F4 screws in parts 9#.

10L

10R

10L

10R

7# and parts 9 with

Front Wall Installation

Pre-place 2 pieces F4

screw in each part 12.

Fix parts 12 onto part

pre-placed screws.

PC panels installation

Beams Installation

Fix part 8 on to part 7

with the preplaced F4

screws.

Pre-place 2 pcs F4

screws in each part 9.

Fix parts 16# onto part 8

with F4 screws according to

the figure.

2 pieces screws for each

16# part.

inserted in parts 16.

Install roof crown 17

Combine parts 9#,13#,and 16#

Roof beam Installation and Screwing

Pre-place 2 pieces F4 screws

into each part 16.

with parts B4.

using F4 bolts previously

Corner Fixation Plates Installation

Corner caps B5 & B6

Installation with

the pre-placed

screws.

Upper door rail installation

the window and insert 2

No.20 Installation

Middle Wall Frame No.19 Installation

Roof Middle Frame

Fix 2 pcs F4 screws

in each 19# part.

Please insert 4 screws in

the two 20 profiles beside

screws in other 20 profiles.

2.Assemble braces T2&T1

Window Installation

Fastenings and Reinforcing Ribs Installation

1.Assemble the window base

(B7-15) using bracket(B1).

with the pre-placed F4 scerws

in part 20#.

1.Assemble the six cross

braces(22) and four cross

braces(23) as shown using

the pre-inserted hex bolt(F4).

Wall Panels Installation

Roof Panels Installation

Panel Seats Installation

1) Insert the wall panels P8

into the grooves of 7# and 19#.

2) Button the part S2 onto the

bottom of each P8 panel, then

push the P8 panels to the bottom

against the part 4#.

1.Insert all roof panels (P9,P10).

2.Install gutter(25) to keep roof

panels in place (see next page)

Plastic Parts Installation

Insert two gutters (25)

Drain Profiles,Water Outlet and End Caps Assembly

Finishing / Triming

Using a water level or square to

make sure that your greenhouse

is straight and level.

Tighten hex bolts at this time

Install all end

caps and trim.

Page is loading ...

Hanover HANGRNHS4X6-NAT Installation guide

Brand: Hanover

Model: HANGRNHS4X6-NAT

Type: Installation guide

Hanover HANGRNHS4X6-NAT is a greenhouse with metal base. Here is some brief information about the product:

Overall size: 130 cm x 190 cm x 195 cm (51" x 75" x 76.7")
Door is hinged on the right-hand side
Easy to assemble
Can be fixed on a solid concrete foundation with pre-drilled holes
Do not position your greenhouse in an area exposed to excessive wind

Download PDF

report

Hanover HANGRNHS4X6-NAT Installation guide

Hanover HANGRNHS4X6-NAT Installation guide

Related papers

Other documents