OGAL-466 OGAL-466 User guide

Brand: OGAL-466

Model: OGAL-466

Type: User guide

OGrow Walk-in 6' x 4'

LAWN AND GARDEN

GREENHOUSE

MODEL#

OGAL-466

With Heavy Duty Aluminium Frame

Thank you for purchasing the OGROW™ greenhouse

Follow the assembly and safety instructions in this manual.

If you have any questions, please contact our Customer Service Department

Let's

Grow

Together!

Parts List.........................................

Side Walls.......................................

Back Wall........................................

Front Wall.......................................

Door Frame...................................

Roof and Full Structure.............

The Door.........................................

The Vents........................................

The Panels......................................

3-4

•

PAGE 2

PART# PART NAME PART

IMAGE

Corner Beam

Front Right Roof Beam

Front Left Roof Beam

Rear Right Roof Beam

Rear Left Roof Beam

Right Doorway Support

Left Doorway Support

Rear Support Pole- Left

Rear Support Pole- Right

Side Support Pole

Roof Support Pole

Top Doorway Beam

Corner Bracket

Door Rail

Vent Support Bar

Rear Floor Bar

PART# PART NAME PART

IMAGE QTY.

Front Floor Bar

Vent Stopper

Vertical Door Rail Support

Left Door Support

Rear Horizontal Support

Diagonal Support

Front Horizontal Support

Top Door Bar

Front Diagonal Support

Center Door Bar

Bottom Door Bar

Right Door Support

Vent Side Bar

Door Slider

Vent Bottom Bar

Vent Top Bar

(Including Rollers)

PARTS LIST

PAGE 3

QTY.

PAGE 4

(See page 21)

PARTS LIST

PART# PART NAME PART

IMAGE QTY.

Side Floor Bar

Top Roof Bar

Gutter Bar

Long Door Support Bolt

Door Frame Spacer

Spanner Wrench

Rubber Seal

Bolt

Door Screw

A-I

PART# PART NAME PART

IMAGE

Vent Screw

Panel Clip

Beam End Cap

Gutter End Cap

Rail End Cap- Right

Rail End Cap- Left

Vent Brace

Nut

Polycarbonate Panel

PAGE 4

QTY.

NOTICE:

Read the entire IMPORTANT SAFETY INFORMATION section

at the beginning of this document – including all text under subheadings

– before set up or use of this product.

PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

KEEP THEM IN A SAFE PLACE WHERE YOU CAN REFER TO THEM AS NEEDED.

The warnings, precautions, and instructions discussed in this manual cannot cover all possible

conditions and situations that may occur. The user must understand that common sense and

caution are factors which cannot be built into this product, but must be supplied by the user.

Assembly/Installation Precautions

1. Assemble only according to these instructions. Improper assembly can create hazards.

2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly. We recommend

that two people together assemble the greenhouse for a smooth and efficient assembly.

3. This unit contains pieces with sharp edges. The machined edges of the aluminium parts and the

ends of the panel clips may be sharp. Handle all parts carefully.

4. Keep assembly area clean and well lit.

5. Keep bystanders out of the area during assembly.

6. Do not assemble when tired or when under the influence of alcohol, drugs or medication.

8. Build the Greenhouse on a flat and level surface. A concrete foundation is recommended for a

high-quality installation.

9. WARNING: The brass bushings inside the Rollers of this product contain lead, a chemical known

to the State of California to cause birth defects (or other reproductive harm). (California Health &

Safety Code § 25249.5, et seq.)

IMPORTANT SAFETY INFORMATION

Use/Service Precautions

1. This product is not a toy. Do not allow children to play in or climb on this product. Although this

greenhouse does include protective covers, there are still some exposed sharp edges. In addi-

tion, protective covers may fall off over time. Children must be supervised if allowed near the

greenhouse.

2. SNOW/DEBRIS ACCUMULATION HAZARD. The heavy weight of accumulated snow or other debris

can cause parts of this greenhouse to buckle suddenly. Do not allow debris to accumulate on

top of the greenhouse. If snowfall is expected, place additional supports (not provided) under-

neath the Crown (35). NEVER enter a greenhouse with accumulated debris on top.

3. Use as intended only. The product capabilities only apply to a properly and completely assembled

product.

4. Inspect periodically; replace damaged parts immediately and do not enter greenhouse if parts

are loose or damaged.

PAGE 5

• Before you assemble this greenhouse, you must build a proper foundation. You may use your

own base of bricks, concrete blocks or treated wood. Whatever foundation you use, ensure that

it is square – by checking that its diagonal measurements are equal – and level, and that the

greenhouse is fastened to it securely. If you have made your own base, you will need to drill

through the sill of the greenhouse.

Your greenhouse needs the proper support of a foundation to help prevent property damage and

injury in the event of strong winds or inclement weather. Wind and ground conditions vary from

site to site, and the characteristics of your site may affect the practicality and effectiveness of

anchoring methods substantially. If you have any doubt regarding the stability of the foundation

you are to use, consult a professional.

• It is always your responsibility to ensure that the greenhouse is properly anchored. Ogrow cannot

be held responsible for personal injury, damage to the greenhouse, or other property damage

that occurs as a result of improperly anchoring the greenhouse.

• Check with local authorities to obtain all required building permits and to familiarize yourself

with any building codes that may apply.

• Decide on a location for the greenhouse. The location should optimally be a level, well lit area

that is sheltered from the wind and free of overhanging branches. The door of the greenhouse

should not open towards the prevailing wind, if possible. Try to locate your greenhouse near a

convenient water source to aid you in watering your plants daily. Also, try to build your

greenhouse in a location where the soil drains easily so that the greenhouse floor is pleasant to

work on.

IMPORTANT:

READ THE FOLLOWING CAREFULLY BEFORE PROCEEDING:

PAGE 6

STARTING TO BUILD

Construct a base first so that the greenhouse can be immediately mounted and secured when it

is completed

Find someone to assist you in the assembly. The work is light and should suit any able-bodied

person, who can speed up and ease assembly by assisting you.

Note that the construction takes time. Work slowly and methodically so that assembly is more

accurate and with fewer errors; rushing only leads to needing to undo and repeat steps done

erroneously. If this is your first time building a greenhouse it may take a good chunk of a day to

complete the construction properly.

Prepare the tools you will need:

• A Drill

• A Screwdriver

• A Spanner – Part 41

Lay out all the greenhouse parts around the base to ensure that nothing is missing. (See image

below.) If any parts are missing, contact us at once so that we can send you the missing parts

right away.

When you assemble the greenhouse, secure parts loosely where possible and then tighten only

when everything is in place. This allows for easy minor adjustments during construction.

GETTING READY

PAGE 7

BACK WALL

FRONT WALL SIDE WALLSIDE WALL

VENTS ROOF DOOR

Lay out all the parts needed for the side wall, following the layout shown below. The grooves in the

support poles should be facing you. The oor bar and gutter bar should be perpendicular to the

oor, with the wider end at the top.

PART 1 – SIDE WALLS

ASSEMBLING THE GREENHOUSE

Part# Part Name Part Image Qty.

Side Support Pole

Diagonal Support

Side Floor Bar

Gutter Bar

Bolt

Nut

PAGE 8

STEP

43 52

Slide three bolts into the groove of

the support poles part 10.

STEP

Bolt the support poles to the

outside of the floor bar.

STEP

Bolt the bottom of the diagonal

support poles to the inside of the

floor bar.

STEP

Follow the steps below to assemble the Side Walls.

Repeat the above steps to make the second side wall.

43 5243 52

43 52

34 34

PAGE 9

Bolt the top of the side support

poles to the outside of the gutter

bar.

Bolt the top of the diagonal

support poles to the inside of the

gutter bar.

Use the extra bolt in the outer

support poles to attach the

diagonal support pole across the

outer support poles.

STEP

43 52

NOTE:

Each step applies to both relevant wall supports.

Lay out all the parts needed for the back wall, following the layout shown below. Make sure that

the roof beams are on the correct sides as the left and right dier; the grooves in the support poles

are facing you; and that the oor bar is perpendicular to the oor, with the wider end at the top.

PART 2 – BACK WALL

ASSEMBLING THE GREENHOUSE

Part# Part Name Part Image Qty.

Corner Beam

Rear Right Roof Beam

Rear Left Roof Beam

Rear Support Pole- Left

Rear Support Pole- Right

Corner Bracket

Rear Horizontal Support

Diagonal Support

Bolt

Nut

PAGE 10

STEP

1 & 5

STEP

43 52

Attach the corner brackets to the

corner and roof beams. Lay the

bracket above the two beams and

secure loosely.

STEP

Bolt the floor bar to the inside of

the corner beams, securing at

each corner.

STEP

Secure the support poles to the

outer side of the floor bar. Attach the

diagonal supports to the inside of

the floor bar and support poles, all

with the same bolt.

STEP

Slide an extra bolt into the groove

of the support pole. Then bolt the

top of the support poles to the

outside of the roof beams using

another bolt.

STEP

On the inside of each corner bracket,

attach the diagonal supports to the

lowest bolt and the horizontal

support to the second-to-lowest bolt.

Open the bolts, position the

supports, and refasten the bolts.

STEP

Lastly, use the extra bolt in the

grooves of the support poles to

secure the horizontal support

across the two support poles.

STEP

Follow the steps below to assemble the Back Wall.

43 52 43 52

PAGE 11

43 52

NOTE:

Each step applies to both relevant corners/supports.

PART 3 – FRONT WALL

ASSEMBLING THE GREENHOUSE

Part# Part Name Part Image Qty.

Corner Beam

Front Right Roof Beam

Front Left Roof Beam

Right Doorway Support

Left Doorway Support

Top Doorway Beam

Corner Bracket

Door Rail

Front Floor Bar

Vertical Door Rail Support

Front Horizontal Support

Front Diagonal Support

Long Door Support Bolt

Door Frame Spacer

Bolt

Nut

PAGE 12

STEP

1 & 5

STEP

NOTE:

OUTSIDE VIEW

Lay out all the parts needed for the front wall, besides for parts 14 and 19. Follow the same layout as

for the rear wall. (The image below is the outside view, so you must lay the pieces out in mirror image

to start with.) Make sure that the roof beams are on the correct sides as the left and right dier; the

oor bar is perpendicular to the oor, with the wider end at the top; and that the door frame parts are

below the frame parts – on the outside.

43 52

Attach the corner brackets to the

side and roof beams. Lay the

bracket above the two beams and

secure loosely.

Bolt the floor bar to the inside of

the corner beams, securing at

each corner

STEP

Secure the support poles to the

outer side of the floor bar. Attach

the diagonal supports to the

inside of the floor bar and support

poles, all with the same bolt.

Slide an extra bolt into the groove

of the support pole. Then bolt the

top of the support poles to the

outside of the top roof beams

using another bolt.

On the inside of each corner bracket,

attach the diagonal supports to the

lowest bolt and the horizontal support

to the second-to-lowest bolt. Open the

bolts, position the supports, and

refasten the bolts.

STEP

Bolt the two short horizontal

supports to the insides of the

support poles.

STEP

Attach the top doorway beam to the outside of the roof beams, using the

top hole in the beam. Next insert a bolt from the outside into the lower

hole at each end, securing loosely with a nut.

STEP

Follow the steps below to assemble the Front Wall.

Note:

Steps 1 - 5

follow the same

steps used for the

back wall.

43 52

PAGE 13

STEP

43 52 03

STEP

13 43

STEP

17 07

NOTE:

Each step applies to both relevant corners/supports.

Slide the door rail onto the bolt heads,

starting on the left until it reaches the

right end of the top doorway beam.

(Note: when you stand the wall up, the

rail will extend on the left of the

greenhouse.) When the rail is in place,

tighten the two bolts.

STEP

Insert a bolt into the hole at the end

of the door rail, securing with a nut.

This will act as a door stop.

STEP

Attach the vertical door rail

support to the end of the door rail

that is jutting out of the structure.

STEP

Secure the bottom of the vertical door

rail support to the outside of the roof

beam, using the long door support

bolt. Slide the door spacer onto the

bolt between the two poles, securing

the joint with a nut on the inside of

the roof beam.

Follow the steps below to assemble the Door Frame.

PAGE 14

43 52

38 39 52

STEP

Turn the assembled wall over so that the outside is now facing you, to make

attaching the door frame easier.

This section completes the greenhouse frame by joining the 4 walls and completing the roof. At this

stage it is best if two people work together.

Collect all the parts needed for the roof and keep on the side until necessary.

PART 4 – FULL STRUCTURE AND ROOF

ASSEMBLING THE GREENHOUSE

Part# Part Name Part Image Qty.

Roof Support Pole

Top Roof Bar

Beam End Cap

Gutter End Cap

Bolt

Nut

PAGE 15

STEP

1STEP

STEP

43 52

Attach the gutter end and beam

end plastic caps to the ends of

the appropriate poles, covering

the exposed edges for your

protection.

STEP

Lift the walls and bolt the side

floor bars to the inside of the

corner beams at each corner.

STEP

Attach the ends of the gutter bars

to the inside of the corner sections

on the adjoining walls. The four

walls are now connected in a

rectangular formation.

STEP

Bolt the top roof bar to the

underside of the roof beams,

securing with two bolts - one

through each of the roof beams.

Repeat at the other end of the roof.

Attach the roof support poles to the

outside of the top roof bar and the

gutter bars. Slide an extra bolt into

each pole before securing.

Lift the greenhouse structure onto

the prepared base and secure

loosely. Check the frame is square

by measuring the diagonals to be

equal. Tighten all nuts after making

sure the greenhouse is sitting

securely on the base.

STEP

Follow the steps below to assemble Full Structure and Roof.

STEP

43 52

PAGE 16

STEP

NOTE:

Each step applies to all relevant corners/supports.

Lay out all the parts needed for constructing the door, following the layout shown. The open sides of

parts 24, 26 and 27 should be facing down.

PART 5 – THE DOOR

ASSEMBLING THE GREENHOUSE

24 26 26 27

Part#

Left Door Support

Top Door Bar

Center Door Bar

Bottom Door Bar

Right Door Support

Door Slider (Including Rollers)

Door Screws

Rail End Cap- Right

Rail End Cap- Left

Bolt

Nut

Part Name Part Image Qty.

PAGE 17

Screw through the door side

supports into the top door bar, on

each side. Repeat for the two

center door bars.

STEP

Attach the bottom door bar as in

step 1. Make sure that the double

edge of the bar is the lower edge.

STEP

Bolt the door slider to the outside

of the top door bar. The curved end

with the door rollers should stand

above the top door bar, with the

rollers visible.

STEP

Make sure the door seals are in

place in the two door side support

bars, and trim any rubber that

sticks out.

Lift the door into an upright position

and ease the bottom bar onto the

door track on the front floor bar.

Slide the door slider onto the door

rail, sliding the rollers onto the

track.

Attach the plastic rail end caps on

each end of the door rail. Tighten

all the bolts in the door structure so

that the door is held firmly and

cannot wobble

STEP

Follow the steps below to assemble the Door.

STEP

PAGE 18

49 50

Right Left

27 42

24 20

STEP

Lay out all the parts needed for constructing the vents, following the layout shown. The greenhouse

has two window vents, but instructions are for a singular vent as the procedure for installation is the

same. Pay particular attention to the way that each bar should be laid, using the images for guidance.

PART 6 – THE VENTS

ASSEMBLING THE GREENHOUSE

Part# Part Name Part Image Qty.

A-I

Vent Support Bar

Vent Stopper

Vent Side Bar

Vent Bottom Bar

Vent Top Bar

Vent Panels

Vent Screw

Vent Brace

Bolt

Nut

30 30

PAGE 19

Slide the vent top bar into the vent

side bars, just over the outermost

layer. The top bar should be

positioned in the lower groove of

the side bars.

STEP

Insert bolts into the bottom of the

two vent side bars, securing loosely.

Slide polycarbonate panel E into

the slot between the two narrow

sheets of the bars, after removing

the protective film on both sides.

STEP

Attach the vent bottom bar to the

outside of the vent side bars, using

the bolts inserted in the previous

step. The top lip of the bottom bar

should slide over the polycarbonate

panel, securing it in place.

STEP

Check that the vent is square by

measuring that the diagonals are

the same, and then tighten the

bolts in each corner. Slide the

completed vent into the top roof bar

to the space between the two roof

support poles.

Turn the vent over and attach the

brace to the vent bottom bar,

screwing it into the pre-drilled

holes.

STEP

Attach the two vent stoppers to the

vent support bar, screwing into the

pre-drilled holes. Attach the stoppers

so that the projecting piece will stick

up into the space of the vent.

STEP

Follow the steps below to assemble the Vents.

Repeat the above

steps for the second

greenhouse vent.

PAGE 20

Attach the vent support bar under

the vent, using the extra bolts in the

roof support poles. Check that the

bar is flushwith the vent before

securing.

Page is loading ...

OGAL-466 OGAL-466 User guide

Brand: OGAL-466

Model: OGAL-466

Type: User guide

Download PDF

report

OGAL-466 OGAL-466 User guide

OGAL-466 OGAL-466 User guide

Other documents