WarmlyYours TW-ST-06PS-PL-HD Installation guide

WarmlyYours
Brand
WarmlyYours
Model
TW-ST-06PS-PL-HD
Type
Installation guide
Installation Support • No Nonsense™ Warranty •(800) 875-5285 • www.WarmlyYours.com
INSTALLATION
As shown in the picture, push the short
screw (6) through the hole in the sheet
metal of the bracket (1)
Tighten the short screw (6) with a screwdriver. Note that
the hole of the bracket (1) should face downward towards
the floor when the towel rail is mounted to the wall.
Attach the three remaining brackets (1) to the vertical tubes
by repeating steps 1 through 3.
Use a tape measure to measure the distance between
these four mounting holes. Use the tape measure to get
the distances of A-B, A-C, C-D, B-D, A-D, and B-C.
Use a drill with an appropriately sized drill bit to make the
holes for A, B, C, and D. If mounting to a stud, only drill
holes B & D.
Use the short screw (6) to attach the bracket
onto the metal pad located on the rear of the
vertical tube.
PAGE 1
TOOLS REQUIRED
Use a pencil to mark locations A, B, C, D on the wall
according the measurements. We suggest mounting the
Towel Warmer at least 24” (600mm) above the floor. We
suggest mounting the left rail of the towel warmer to a
stud, if possible.
A B
C D
600mm
1
2
3
4
5
7
+
STUDIO TOWEL WARMER INSTALLATION MANUAL
ITEM# TW-ST-06PS-PL-HD
6
(1) + (2) Round Wall hang bracket + set screw
(3) 3pc Bushings and 1pc short tube for wall bracket
(4) Long screw
(5) Plastic wall anchor
(6) Short screw
(7) Hex Key Wrench
1. & 2.
3.
4.
5.
6.
7.
ACCESSORIES
Installation Support • No Nonsense™ Warranty •(800) 875-5285 • www.WarmlyYours.com
STUDIO TOWEL WARMER INSTALLATION MANUAL
ITEM# TW-ST-06PS-PL-HD
Push the long screw (4) through the bushing or
short tube (3), then screw into the plastic wall
anchor (5) or stud.
Use a hammer to install the plastic wall anchors
(5) completely into the wall, where needed.
Install the bracket onto the bushing or short tube (3).
As shown in the picture, screw the set screw (2) into the
hole of the bracket (1) with the hex wrench; tighten the
screw (1) into the bushing or short tube (3).
Attach the remaining three brackets by repeating step 11.
The installation is now complete. Wipe the tubes clean.
10
11
12
8
9
PAGE 2
INSTALLATION
TOOLS REQUIRED
(1) + (2) Round Wall hang bracket + set screw
(3) 3pc Bushings and 1pc short tube for wall bracket
(4) Long screw
(5) Plastic wall anchor
(6) Short screw
(7) Hex Key Wrench
1. & 2.
3.
+
4.
5.
6.
7.
ACCESSORIES
Page is loading ...
MANUEL D’INSTALLATION PORTE-SERVIETTE CHAUFFANT STUDIO
CODE DU PRODUIT: TW-ST-06PS-PL-HD
Placer la vis longue dans la douille, puis dans la
cheville.
Utiliser un marteau pour fixer la cheville (5) dans
le mur.
Installer le porte-serviette dans la douille.
Comme sur la photo, fixer la vis intérieure au support avec
le tournevis fournit.
Répéter l’opération pour les 3 autres supports.
10
11
12
8
9
PAGE 2
INSTALLATION
OUTILS REQUIS
+
(1) + (2) Support rond pour le mur + vis
(3) 3 douilles and tube court pour la fixation au mur
(4) Vis longue
(5) Une cheville en plastique
(6) Vis courte
(7) Tournevis
1. & 2.
3.
4.
5.
6.
7.
PIECES
Service Technique 24/7 • Garantie Complète •(800) 875-5285 • www.WarmlyYours.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

WarmlyYours TW-ST-06PS-PL-HD Installation guide

WarmlyYours
Brand
WarmlyYours
Model
TW-ST-06PS-PL-HD
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents