WarmlyYours LAVA Side Cover Installation guide

WarmlyYours
Brand
WarmlyYours
Model
LAVA Side Cover
Type
Installation guide

WarmlyYours LAVA Side Cover

Protect your LAVA with our durable, high-temperature polycarbonate side covers. These covers are designed to fit snugly around the sides of your LAVA, leaving a 1mm gap between the cover and the glass. This gap allows for proper ventilation and prevents the covers from overheating.

The side covers are easy to install. Simply clean the sides of your LAVA with rubbing alcohol, attach the double-sided tape around the outer edge of the unit, and then carefully position each polycarbonate panel along the edges of the LAVA. Once the panels are in place, verify adhesion and mount your LAVA as shown in the LAVA Installation Manual.

WarmlyYours LAVA Side Cover

Protect your LAVA with our durable, high-temperature polycarbonate side covers. These covers are designed to fit snugly around the sides of your LAVA, leaving a 1mm gap between the cover and the glass. This gap allows for proper ventilation and prevents the covers from overheating.

The side covers are easy to install. Simply clean the sides of your LAVA with rubbing alcohol, attach the double-sided tape around the outer edge of the unit, and then carefully position each polycarbonate panel along the edges of the LAVA. Once the panels are in place, verify adhesion and mount your LAVA as shown in the LAVA Installation Manual.

Installation Support • No Nonsense™ Warranty •(800) 875-5285 • www.WarmlyYours.com
KIT Contents: Two (2) rolls of Scotch TM brand Mounting Tape ½” x 75”
Four (4) Pieces of pre-cut, high-temperature polycarbonate
Step 1. Verify that the correct sizes and quantity of polycarbonate pieces have been received and inspect cosmetic condition of each piece.
Step 2. Test t each cover to verify proper dimensions and t. Take special note of clearance in areas around the pilot light and power switch.
Contact WarmlyYours if any dimensions are incorrect.
Step 3. Using a cotton ball or rag soaked in rubbing alcohol, clean all 4 sides of the lava as shown
Step 4. After the sides of the Lava have dried, attach the double-sided tape around the entire outer edge of the unit as shown.
More than one roll of tape may be needed to accomplish this. Do NOT peel the backing off of the tape yet.
Lava Side Cover
Installation Instructions
Installation Support • No Nonsense™ Warranty •(800) 875-5285 • www.WarmlyYours.com
Step 5. Use a nger to push the entire length of the tape surface rmly to the Lava.
Step 6. Once the tape has been completely adhered to the sides of the unit, use a ngernail to separate the backing from the tape.
Step 7. Slowly peel the backing paper from the tape, exposing the outer adhesive layer.
Step 8. Carefully position each polycarbonate panel along the edges of the Lava. Leave a 1mm gap between the polycarbonate and the glass.
Verify correct positioning of the panels before making contact with the tape. Once the panel has been attached to the mounting tape, it
is very difcult to reposition it. Removing the panel from the tape and repositioning it may reduce the holding power of the tape. If the
tape loses its tack, the tape may need to be removed and new tape put in its place. If the tape needs to be replaced, be sure to clean
any remaining residue with a rag or cotton ball soaked with alcohol. Let alcohol dry before installing new tape.
Step 9. Verify adhesion of polycarbonate to the LAVA. Mount LAVA as shown in LAVA Installation Manual.
Lava Side Cover
Installations Instructions
1mm gap between
glass and cover
Cover
Cover
  • Page 1 1
  • Page 2 2

WarmlyYours LAVA Side Cover Installation guide

WarmlyYours
Brand
WarmlyYours
Model
LAVA Side Cover
Type
Installation guide

WarmlyYours LAVA Side Cover

Protect your LAVA with our durable, high-temperature polycarbonate side covers. These covers are designed to fit snugly around the sides of your LAVA, leaving a 1mm gap between the cover and the glass. This gap allows for proper ventilation and prevents the covers from overheating.

The side covers are easy to install. Simply clean the sides of your LAVA with rubbing alcohol, attach the double-sided tape around the outer edge of the unit, and then carefully position each polycarbonate panel along the edges of the LAVA. Once the panels are in place, verify adhesion and mount your LAVA as shown in the LAVA Installation Manual.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents