Speakman SEF-9200 Installation guide

Speakman
Brand
Speakman
Model
SEF-9200
Category
Sanitary ware
Type
Installation guide

Speakman SEF-9200 is an eyewash unit designed to provide a continuous flow of flushing fluid in case of an emergency. It is easy to install and maintain, and comes with a 5-year warranty.

The SEF-9200 is equipped with a vacuum breaker assembly to prevent backflow of contaminated water into the potable water supply. It also has a threaded insert to create a seal between the sink fitting and the adapter.

The eyewash is activated by squeezing the handle until it locks into the ON position. To deactivate, the handle is squeezed while lifting the stay-open plunger.

The SEF-9200 is made of durable materials and is resistant to corrosion and scaling. It is also easy to clean and maintain. The eyewash valve has a rubber seat washer, which may require periodical maintenance. The eyewash unit can be cleaned using a mild soap and warm water solution.

Speakman SEF-9200 is an eyewash unit designed to provide a continuous flow of flushing fluid in case of an emergency. It is easy to install and maintain, and comes with a 5-year warranty.

The SEF-9200 is equipped with a vacuum breaker assembly to prevent backflow of contaminated water into the potable water supply. It also has a threaded insert to create a seal between the sink fitting and the adapter.

The eyewash is activated by squeezing the handle until it locks into the ON position. To deactivate, the handle is squeezed while lifting the stay-open plunger.

The SEF-9200 is made of durable materials and is resistant to corrosion and scaling. It is also easy to clean and maintain. The eyewash valve has a rubber seat washer, which may require periodical maintenance. The eyewash unit can be cleaned using a mild soap and warm water solution.

INSTRUCTIONS FOR MODELS
92-SEF-9200-02
For additional assistance or service please contact:
SPEAKMAN
®
Company
400 Anchor Mill Road
New Castle, DE 19720
800-537-2107
customerser[email protected]
www.speakman.com
SEF-9200
Works With:
SPEAKMAN SC-581X / 583X / 585X Faucets
Ferguson ProFlo PF1119
Fiat 830AA
TOOLS AND SUPPLIES
IMPORTANT
SAFETY TIPS
Cover your drain to prevent loss of parts. Be sure to
wear eye protection while cutting pipe.
MAINTENANCE
The eyewash valve has a rubber seat washer, which
may require periodical maintenance. The eyewash unit
can be cleaned using a mild soap and warm water
solution. Rinse thoroughly and dry immediately with a
soft, clean cloth for best results.
WARRANTY
Additional warranty information can be found at:
www.speakman.com
Be sure to read instructions thoroughly before beginning
installation. Do not overtighten any connections or damage
may occur. The supply line for plumbed eyewash units shall
provide an uninterruptible supply of flushing fluid at a
minimum of 30 psi flowing pressure. If a shut off valve is
installed in the cold supply line of the sink fitting (which
supplies the eyewash) for maintenance purposes, provisions
shall be made to prevent unauthorized shut off. The sink
fitting does not have to be turned on for the eyewash to
operate. ANSI Z358.1 requires that all emergency
equipment shall be tested weekly to verify proper operation
and inspected annually to assure conformance with ANSI
Z358.1-2009 requirements.
LevelPhillips
Screwdriver
Adjustable
Wrench
Thread Seal
Tape
5/16” Hex
Key Wrench
Measuring
Tape
Pencil
1
After shutting off water supplies, remove the
Cold Supply Stop from Faucet.
2
After cleaning the seat, thread the Stop Adapter
into the Cold Supply Stop location of Faucet.
Wrench tighten.
3
Tighten the Threaded Insert to create a seal
between the Sink Fitting and the Adapter using
a 5/16” Allen Wrench in the base of the
Adapter.
4
After applying Thread Sealant Tape, thread the
Vacuum Breaker Assembly (1) onto the Stop
Adapter. Wrench tighten.
5
Attach Hose end to the the Vacuum Breaker
Assembly. Wrench tighten.
6
After reviewing the Roughing In Diagram, select
a suitable location for installation. Using the
Mounting Bracket as a template, transfer
mounting locations to wall using a pencil.
Be sure Bracket is level and plum.
7
Secure Bracket to wood structure (i.e. wall stud)
or similar using the supplied screws.
Note: If not mounting directly into a wood structure use
appropriate hardware capable of supporting item.
8
Attach remaining end of Hose to the base of
the Eyewash. Wrench tighten.
9
The eyewash is activated by squeezing the
Handle (1) until it locks into the ON position.
To deactivate, the Handle is squeezed while
lifting the Stay-Open Plunger (2).
ROUGH-IN DIAGRAMS / REPAIR PARTS
SPEAKMAN
®
DIMENSIONS SUBJECT TO CHANGE WITHOUT NOTICE.
8"
203mm
4"
102mm
WALL BRACKET
(SUPPLIED W/#10
WOOD SCREWS)
TWIN HEAD
AUTO STAY-
OPEN EYEWASH
6 FT (20m) HOSE
VACUUM
BREAKER
COLD INTEGRAL
STOP SPINDLE
& RETAINING
NUT REMOVED
SERVICE SINK
FITTING
3"
77mm
10"
253mm
1
1
2
"
39mm
33" (83.8CM) TO 45"
(114.3CM) TO FLOOR
6
1
4
"
161mm
RPG38-0390 - Yellow Spray Head Assembly
RPG45-0033 - Rubber Seat Washer And Screw
Note: Dimensions shown are for SPEAKMAN SC-5811
service sink. Dimensions shown for reference only.
NOTE: If not mounting directly into a wood structure
use appropriate hardware capable of supporting item.
  • Page 1 1
  • Page 2 2

Speakman SEF-9200 Installation guide

Speakman
Brand
Speakman
Model
SEF-9200
Category
Sanitary ware
Type
Installation guide

Speakman SEF-9200 is an eyewash unit designed to provide a continuous flow of flushing fluid in case of an emergency. It is easy to install and maintain, and comes with a 5-year warranty.

The SEF-9200 is equipped with a vacuum breaker assembly to prevent backflow of contaminated water into the potable water supply. It also has a threaded insert to create a seal between the sink fitting and the adapter.

The eyewash is activated by squeezing the handle until it locks into the ON position. To deactivate, the handle is squeezed while lifting the stay-open plunger.

The SEF-9200 is made of durable materials and is resistant to corrosion and scaling. It is also easy to clean and maintain. The eyewash valve has a rubber seat washer, which may require periodical maintenance. The eyewash unit can be cleaned using a mild soap and warm water solution.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents