Digigram IQOYA *LINK User manual

IQOYA *LINK & IQOYA *LINK/LE

Stereo IP audio codecs for

Studio to Studio Links

&

Studio to Transmitter Links

User manual (valid from firmware 2.40c)

June 2014

IQOYA *LINK - IQOYA *LINK/LE

IP Audio Codec

3

instructions.

r

as specified in this manual

ck any of the ventilation openings!

. Do not place objects filled

ce.

onnecting means in the immediate

The plug shall be easily accessible in case of a

or heating

roduct to an IT power supply system

orway.

s, which may damage the finish of metal or other

ture, does not operate

dropped.

ect any

cables that connect with other components.

cordon d’ali

Important Safety Information

read carefully before using this equipment!

Throughout this manual,

the lightning bolt triangle

is used to alert the user to

the risk of electric shock.

Follow these instructions and keep them in a safe place! Keep in mind that damages due to failure to

observe the instructions contained in this manual are not covered by warranty.

Instructions importantes de sécurité

lire soigneusement avant d’utiliser l’équipement!

The exclamation point

triangle is used to alert the

user to important operating

or maintenance

Lisez et suivez ces instructions. Conservez les pour consultation ultérieure! Les dommages dus au non-

respect des instructions contenues dans ce manuel ne sont pas couverts par la garantie.

Wichtige Sicherheitshinweise

vor Inbetriebnahme des Gerätes sorgfältig lesen!

Befolgen Sie die Anweisungen und bewahren Sie sie für spätere Fragen auf! Bei Schäden, die durch

Nichtbeachten dieser Bedienungsanleitung verursacht werden, erlischt der Garantieanspruch!

Ne pas ouvrir l’appareil

Do Not Open the Cabinet

There are no user-serviceable components

inside this product. Opening the cabinet

may present a shock hazard, and any

modification to the product will void your warranty. If it

is necessary to open the device for maintenance or

advanced configuration purposes, this is to be done by

qualified personnel only after disconnecting the powe

Gerät nicht öffnen

L’ouverture du coffret peut produire un

risque de choc électrique, et toute

modification du produit annule votre

garantie. S’il est nécessaire d’ouvrir l’appareil pour

l’entretien ou la configuration avancée, cela doit être fait

par du personnel qualifié, après avoir débranché le

mentation et les câbles réseaux !

Öffnen des Geräts kann eine Gefährdung

durch Stromschlag und Erlöschen der

Garantie zur Folge haben. Reparaturarbeiten

und Änderungen der Hardwarekonfiguration dürfen nur

von qualifiziertem Personal nach entfernen der Strom-

und Netzwerkkabel durchgeführt werden.

Stromversorgung

Alimentation

cord and network cables!

Power supply

The device is to be connected only to a

power supply

and marked on the equipment.

This equipment must be earthed!

Do not blo

Humidity

To reduce the risk of fire or shock, do not expose this

device to rain or moisture

with liquid on this devi

Installation Location

To ensure proper operation and to avoid safety hazards,

the device must be installed in a 19“ rack mount chassis.

The electrical installation of the building should dispose

of easily accessible disc

vicinity of the device.

If rack installation is not possible, place it on a firm and

level surface. The use of a supply lead with a power plug

respecting the legal standards in the country of use is

obligatory.

problem.

Avoid installation in extremely hot or cold locations, or

in an area that is exposed to direct sunlight

equipment. Avoid moist or humid locations.

Connection of this p

is only in N

Cleaning

Clean only with a soft, dry cloth. If necessary, after

disconnecting the unit’s cables, wipe it with a soft cloth

dampened with mild soapy water, then with a fresh cloth

with clean water. Wipe dry immediately with a dry cloth.

NEVER use benzene, aerosol cleaners, thinner, alcohol or

any other volatile cleaning agent. Do not use abrasive

cleaner

parts.

Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power supply cord or plug

is damaged, liquid has been spilled, the apparatus has

been exposed to rain or mois

normally, or has been

Moving the device

Before moving the unit, be certain to disconn

Il est primordial de connecter l’appareil à

une alimentation électrique telle que

spécifiée dans ce manuel d´utilisateur et sur

le matériel même.

Das Gerät darf nur mit der in dieser

Bedienungsanleitung und auf dem Gerät

angegebenen Stromversorgung betrieben

werden.

Erdung ist zu gewährleisten!

Cet équipement doit être raccordé à la terre !

Belüftungsschlitze nicht verdecken!

N’obstruer aucune ouverture de ventilation !

Humidité

Wasser und Feuchtigkeit

Afin de réduire les risques de feu ou de choc, n’exposez

pas cet appareil à la pluie ou l’humidité. Ne placez pas

d´objet contenant un liquide sur l’appareil.

Um Brand- oder Stromschlagrisiken zu vermeiden, darf

das Gerät nicht mit Feuchtigkeit in Berührung kommen.

Aufbau des Geräts

Installation, mise en place

Um den einwandfreien Betrieb zu gewährleisten und

Sicherheitsrisiken zu vermeiden, sollte das Gerät in

einem 19-Zoll Baugruppenrahmen montiert werden. Die

elektrische Installation des Gebäudes sollte über einen

leicht zugänglichen Trennschalter in unmittelbarer Nähe

des Geräts verfügen Nur wenn die Installation im Rack

nicht möglich ist, stellen Sie das Gerät auf einen festen,

waagerechten Untergrund.

Afin d’assurer le fonctionnement correct et de minimiser

les risques potentiels liés à la sécurité, l’appareil doit être

installé dans un châssis 19 pouces. Si cela ne vous est pas

possible, placez-le sur une surface solide et plane. Prévoir

dans l’installation électrique du bâtiment un dispositif de

sectionnement aisément accessible et à proximité

immédiate de l’appareil.

L’utilisation d’un câble d’alimentation avec une fiche de

prise de courant respectant les normes en vigueur dans le

pays d’utilisation est obligatoire. De plus la fiche de prise

de courant doit être aisément accessible en cas de

problème.

Die Verwendung eines Anschlußkabels und eines

Steckers, die die im Benutzungsland gültigen Normen

erfüllen, ist obligatorisch. Des weiteren muß die

Steckdose für einen eventuellen Problemfall leicht

zugänglich sein.

Évitez une installation dans des endroits très chauds ou

très froids ainsi que dans des lieux exposés directement

au soleil. Évitez les lieux présentant un excès d’humidité.

Le raccordement de ce produit à un régime

d’alimentation IT n’est possible qu’en Norvège.

Meiden Sie Standorte in der Nähe von Wärme- oder

Feuchtigkeitsquellen sowie direkte Sonneneinstrahlung.

Anschluß dieses Produktes an eine spezielle IT-

Stromversorgung ist nur in Norwegen genehmigt.

Nettoyage

Nettoyez uniquement avec un chiffon doux et sec. Si

nécessaire, après avoir débranché le cordon

d´alimentation, essuyez-le avec un chiffon doux

humidifié avec de l´eau savonneuse puis rincez le á l´aide

d un chiffon propre et d´eau claire.

Reinigen des Geräts

Säubern Sie das Gerät nur mit einem weichen, trockenen

Tuch. Bei Bedarf verwenden Sie ein mit mildem

Seifenwasser befeuchtetes Tuch, nachdem Sie die

Netzanschlusskabel aus der Steckdose gezogen haben,

anschließend ein weiches, mit klarem Wasser

befeuchtetes Tuch. Trocken Sie das Gerät sofort im

Anschluß. Keinesfalls Benzol, Verdünner oder sonstige

starke Lösungsmittel oder Scheuerreiniger verwenden, da

hierdurch das Gehäuse beschädigt werden könnte.

Séchez-le immédiatement avec un chiffon sec. N’utilisez

JAMAIS d´essence, de nettoyants en aérosols, d´alcool ou

tout autre agent nettoyant volatile. N’utilisez pas de

produits nettoyants abrasifs qui pourraient endommager

les finitions métalliques ou d´autres pièces.

Réparation

Lassen Sie etwaige Reparaturen nur von qualifizierten

Fachleuten durchführen!

Lorsque l’appareil a été endommagé quelle qu’en soit la

cause ou qu’il ne fonctionne pas normalement, toute

réparation doit être effectuée par du personnel qualifié.

Avant de transporter l´unité, assurez-vous d´avoir bien

déconnecté le cordon d’alimentation ainsi que tous les

câbles la reliant à d´autres appareils.

Sollten das Netzkabel oder der Netzstecker beschädigt

sein, oder sollte das Gerät selbst beschädigt worden sein

(z. B. durch Eindringen von Feuchtigkeit durch Fall auf

den Boden), oder sollte es nicht ordnungsgemäß

funktionieren oder eine deutliche Funktionsabweichung

aufweisen, so ist es von qualifizierten Fachleuten zu

reparieren.

IQOYA *LINK - IQOYA *LINK/LE

Stereo IP Audio Codec

4

TABLE OF CONTENTS

INFORMATION FOR THE USER.................................................................................................................................. 7

KEY HARDWARE FEATURES...................................................................................................................................... 9

KEY SOFTWARE FEATURES ..................................................................................................................................... 10

IQOYA *LINK AUDIO ALGORITHMS .............................................................................................................................. 12

IQOYA *LINK/LE AUDIO ALGORITHMS ........................................................................................................................ 12

FRONT AND BACK PANELS ....................................................................................................................................... 13

IQOYA *LINK FRONT PANEL........................................................................................................................................ 13

IQOYA *LINK/LE FRONT PANEL.................................................................................................................................. 16

IQOYA*LINK AND IQOYA *LINK/LE BACK PANEL................................................................................................... 18

INSTALLATION AND CONFIGURATION ................................................................................................................ 19

CONNECTING THE IQOYA *LINK OR IQOYA *LINK/LE............................................................................................. 19

WEB ACCESS RIGHTS ...................................................................................................................................................... 19

“Administrator” category .......................................................................................................................................... 19

“User” category......................................................................................................................................................... 19

“Read-only” category ................................................................................................................................................ 20

REMOTE CONFIGURATION THROUGH HTML PAGES .......................................................................................................... 20

HTTP bandwidth limitation........................................................................................................................................ 21

Network parameters configuration............................................................................................................................. 22

NTP date and time synchronization............................................................................................................................ 25

Audio synchronization based on NTP clock (optional feature).................................................................................. 25

Global audio parameters configuration..................................................................................................................... 27

Encoder parameters configuration............................................................................................................................. 30

Encoder input configuration....................................................................................................................................................... 30

Encoder output configuration..................................................................................................................................................... 31

RTP streaming settings.......................................................................................................................................................... 32

MPEG-TS/IP SPTS streaming settings.................................................................................................................................. 33

Adding other unicast / multicast destinations ........................................................................................................................ 35

Encoding an IP stream with NTP audio synchronization....................................................................................................... 35

Decoder parameters configuration............................................................................................................................. 36

Decoder input configuration ...................................................................................................................................................... 37

Forward Error Correction ...................................................................................................................................................... 39

Decoder output configuration..................................................................................................................................................... 43

Decoder status information ........................................................................................................................................ 44

RS232 tunneling configuration .................................................................................................................................................. 48

GPIOs tunneling configuration .................................................................................................................................................. 48

AUTHORIZING A USER TO UPLOAD PLAYLISTS TO THE SD CARD VIA FTP ............................................ 49

SAVING / LOADING A CONFIGURATION............................................................................................................... 51

SAVE / LOAD THE FULL CODEC CONFIGURATION TO/FROM THE SDHC CARD (SD CARD BACKUP) .................................. 51

DOWNLOAD / UPLOAD THE AUDIO CONFIGURATION TO/FROM A REMOTE STORAGE ........................................................ 51

FAIL-OVER...................................................................................................................................................................... 53

LOSS OF IP STREAM......................................................................................................................................................... 53

POWER SUPPLY FAILURE.................................................................................................................................................. 53

SDHC CARD MANAGEMENT ..................................................................................................................................... 55

SNMP SUPERVISION..................................................................................................................................................... 55

ALARMS MANAGEMENT .................................................................................................................................................. 56

LOG FILE......................................................................................................................................................................... 58

IQOYA *LINK - IQOYA *LINK/LE

IP Audio Codec

5

FIRMWARE UPDATE....................................................................................................................................................59

IQOYA *LINK DISPLAY & KEYPAD .........................................................................................................................60

SYSTEM ........................................................................................................................................................................... 61

ETHERNET 0 MENU (RJ45 “AUDIO” CONNECTOR) ........................................................................................................ 62

ETHERNET 1 MENU (RJ45 “IP BACK UP / CONTROL” CONNECTOR) .............................................................................. 62

VU-METERS ..................................................................................................................................................................... 63

HEADPHONES................................................................................................................................................................... 63

ENCODER ......................................................................................................................................................................... 63

DECODER......................................................................................................................................................................... 64

NETWORK PROTOCOLS.............................................................................................................................................65

Web server............................................................................................................................................................................. 65

FTP (File Transfer Protocol).................................................................................................................................................. 65

SNMP agent........................................................................................................................................................................... 65

DNS (Domain Name Service) service ................................................................................................................................... 65

DHCP (Dynamic Host Configuration Protocol) service ........................................................................................................ 65

NTP (Network Time Protocol) .............................................................................................................................................. 65

SPECIFICATIONS...........................................................................................................................................................66

INPUTS ............................................................................................................................................................................. 66

OUTPUTS.......................................................................................................................................................................... 67

CONNECTIVITY ................................................................................................................................................................ 67

ADDITIONAL PORTS .........................................................................................................................................................67

SOFTWARE, FORMATS, PROTOCOLS.................................................................................................................................. 68

APPENDIX A: BLOCK DIAGRAM...............................................................................................................................69

APPENDIX B: AUDIO CONNECTORS........................................................................................................................69

Audio In.......................................................................................................................................................................69

Audio Out....................................................................................................................................................................69

APPENDIX C: GPIO CONNECTORS...........................................................................................................................70

GPIO PINOUT................................................................................................................................................................... 70

GENERAL PURPOSE INPUTS (GPIS) .................................................................................................................................. 71

GPI optocoupler specifications...................................................................................................................................71

GENERAL PURPOSE OUTPUTS (GPOS) ............................................................................................................................. 72

GPO relay specifications ............................................................................................................................................72

APPENDIX D: SERIAL PORT (RS232 ON DB9).........................................................................................................73

APPENDIX E: TYPICAL LATENCY VALUES...........................................................................................................74

Impact of the processing granularity..........................................................................................................................74

Impact of the network on latency ................................................................................................................................74

Impact of features on the latency ................................................................................................................................74

APPENDIX F: AAC SETTINGS FOR STEREO SAMPLES ......................................................................................76

APPENDIX G: ENHANCED-APT-X SETTINGS FOR STEREO SAMPLES..........................................................78

APPENDIX H: AVAILABLE FEC.................................................................................................................................79

FEC REQUIRING NO ADDITIONAL STREAM .......................................................................................................................79

FEC REQUIRING AN ADDITIONAL STREAM .......................................................................................................................79

Standard FECs............................................................................................................................................................79

Redundant dual streaming FECs ................................................................................................................................80

APPENDIX I: REDUNDANT DUAL STREAMING....................................................................................................81

IQOYA *LINK - IQOYA *LINK/LE

Stereo IP Audio Codec

6

SPATIAL DIVERSITY......................................................................................................................................................... 81

TIME DIVERSITY .............................................................................................................................................................. 81

APPENDIX J: USE CASES............................................................................................................................................. 83

STL WITH BACKUPS ........................................................................................................................................................ 83

STL WITH REDUNDANT DUAL REDUNDANT STREAMING AND TIME DIVERSITY ................................................................ 84

STL WITH TRANSMITTER AUDIO MONITORING ................................................................................................................ 84

AUDIO SYNCHRO FOR MFN: ALL TRANSMITTERS FED THROUGH IP................................................................................. 85

AUDIO SYNCHRO FOR MFN: MIX OF TRANSMITTERS FED THROUGH IP AND TRANSMITTERS FED THROUGH SATELLITE... 86

DELIVERING AN MPEG-TS/IP STREAM TO A DVB BROADCASTER ................................................................................. 87

IP BACKUP TO SATELLITE ................................................................................................................................................ 88

IP TRANSPORT VIA SATELLITE ......................................................................................................................................... 89

IQOYA *LINK - IQOYA *LINK/LE

IP Audio Codec

7

INFORMATION FOR THE USER

This equipment has been tested and found to comply with the limits for a CLASS B digital device, pursuant to Part 15 of the FCC

Rules and with the following European and international Standards for:

User safety: EMC:

European Directive 2006/95/EC "Low Voltage Directive

Europe: EN60950 1 (2006)

International: IEC 60950 1 (2005)

United States: FCC rules Part 15 Class B

International: CISPR22 (2005) Class B + A1/2005 + A2/2006

European Directive: EMC 2004/108/EC

Europe: Disturbance Emissions: EN55022 (2006) +A1/2007 Requirements for

Information Technology Equipment (ITE)

Immunity: EN55024(1998+A1/2001+A2/2003) (ITE)

Harmonics: EN61000-3-2 (2006)

RoHS:

European directive 2002/95/EC aka “RoHS”

Note: to comply with standard EN55024, use shielded network

cables!

In order to guarantee compliance with the above standards in an installation, the following must be done:

· the provided cables must not be modified.

· additional cables used must have their respective shield connected to each extremity.

The limits specified in the standards are designed to provide reasonable protection against harmful interference in an industrial

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

* reorient or relocate the receiving antenna.

* increase the separation between the equipment and the receiver.

* connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

* consult the dealer or an experienced audio/television technician for help.

Note: Connecting this device to peripheral devices that do not comply with CLASS A requirements or using an unshielded peripheral data

cable could also result in harmful interference to radio or television reception. The user is cautioned that any changes or modifications

not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. To ensure

that the use of this product does not contribute to interference, it is necessary to use shielded I/O cables.

Copyright

©

No portion of this manual may be reproduced without prior written consent from Digigram. The copyright protection claimed here includes

photocopying, translation and/or reformatting of the information contained in this manual.

While every effort has been made to ensure accuracy, Digigram is not responsible for errors, omissions or typos, and reserves the right to make

improvements or changes in the products and programs described without notice.

Digigram and the Digigram logo, visiblu and the visiblu logo, and IQOYA are registered trademarks or trademarks of Digigram S.A.. HE-AAC and AAC-

(E)LD are registered trademarks or trademarks of Fraunhofer IIS. All other trademarks are property of their respective holders.

IQOYA *LINK - IQOYA *LINK/LE

Stereo IP Audio Codec

8

You have just acquired a Digigram IQOYA*LINK

OR

IQOYA*LINK/LE

and

we congratulate you!

IQOYA*LINK and IQOYA*LINK/LE are IP stereo audio codecs of the IQOYA range based on Digigram

FluidIPu technology.

They allow for bi-directional transmission of audio signals over IP networks..

Depending on your needs, there are several ways of configuring and controlling IQOYA *LINK or IQOYA

*LINK/LE.

The manual at hand will guide through installation, configuration, and operation. For any software related

issue, please refer to the specific documentation provided in its on-line help.

IQOYA *LINK - IQOYA *LINK/LE

IP Audio Codec

9

KEY HARDWARE FEATURES

IQOYA *LINK IQOYA *LINK/LE

2 balanced analog mono line inputs, with software programmable analog and digital gain.

2 servo-balanced analog mono line outputs, with analog gain

1 AES/EBU stereo input, with hardware sample rate converters up to 125 kHz / 125 dB THD

1 AES/EBU stereo output

1 headphones output (Jack 6.35 mm) with volume

knob

-

2 Neutrik™ EtherCon RJ45™ ports 10/100 Mbps

(auto-negotiation, 10/100, half/full duplex)

1 USB port type A (unused) -

1 SDHC (‘Secure Digital High Capacity’) card reader

8 GPIs and 8 GPOs 4 GPIs and 4 GPOs

1 RS232 serial port

1 LCD TFT display - touchpad interface -

1U 19"rack enclosure

Automatic analog and digital audio hardware bypass in case of absence of power supply.

IQOYA *LINK - IQOYA *LINK/LE

Stereo IP Audio Codec

10

KEY SOFTWARE FEATURES

FEATURE IQOYA *LINK IQOYA *LINK/LE

Support of unicast, multi-unicast, multicast, multi-multicast

addressing (New!)

Yes Yes

Support of IGMP v3 (New!) Yes Yes

MPEG-TS/IP SPTS streaming (New!) Yes Yes

Configurable routing table Yes Yes

Dual port redundant streaming with time diversity up to 1 second

(New!)

Yes Yes

VLAN Tagging + DSCP Yes Yes

Support of DHCP Yes Yes

Possibility to encode and decode IP streams and play sound files

which sampling frequency is different from IQOYA frequency

(except 44.1 <-> 48 kHz frequency change for RTP streams).

Yes Yes

3 decoding priorities Yes Yes

Automatic switch to a lower decoding priority (backup) in case

main IP stream is lost, with configurable switching criteria

(duration of IP stream loss / recovery)

Yes Yes

Backup 1: IP stream (RTP, HTTP), audio inputs, file or playlist on

SDHC card

Yes Yes

Backup 2: audio inputs, file or playlist on SDHC card Yes Yes

Possibility to disable/enable any defined priority Yes Yes

Alarms notifications: configurable as SNMP Trap, GPO, log file Yes Yes

Possibility to stop streaming on input silence detection with

adjustable silence threshold and duration.

Yes Yes

Selectable FECs Yes Yes

Automatic audio format detection on the decoder (New!) Yes Yes

Real time metrics on network path quality (jitter, lost packets,

duplicated packets, disordered packets) for the primary stream as

well as for the FEC stream.

Yes Yes

Adjustable jitter buffer Yes Yes

Management of lost packets, disordered packets duplicated packets,

and AAC error concealment

Yes Yes

RS232 tunneling Yes Yes

GPIO tunneling Yes Yes

SNMP SET, GET and traps (Multiple trap destinations) Yes Yes

WEB user rights management Yes Yes

NTP synchronization (date and time) Yes Yes

Audio synchronization on NTP clock Optional Optional

Log file Yes Yes

IQOYA *LINK - IQOYA *LINK/LE

IP Audio Codec

11

Save / load full codec configuration Yes Yes

Save / load audio configuration Yes Yes

Remote firmware update

Audio still active while firmware uploading

Uploaded firmware can be applied from WEB site or SNMP.

Possibility to keep on SD card firmware version N and N-1

Yes Yes

Give a user the right to upload soundfiles and playlists to the

SDcard via by FTP , and to select the active playlist. (New!)

Yes Yes

IQOYA *LINK - IQOYA *LINK/LE

Stereo IP Audio Codec

12

IQOYA *LINK audio algorithms

Included

• linear 16/24-bit PCM

• ITU G.711/722

• ISO MPEG-1/2 Layer I, Layer II, Layer III

• Free option: AAC or Enhanced apt-X

Optional

• AAC-LC, HE-AACv1 (LC+SBR), HE-AACv2 (LC+SBR+PS), AAC-LD, AAC-ELD

• Enhanced apt-X

IQOYA *LINK/LE audio algorithms

• linear 16/24-bit PCM

• ITU G.711/722

• ISO MPEG-1/2 Layer I, Layer II, Layer III

• AAC-LC, HE-AACv1 (LC+SBR), HE-AACv2 (LC+SBR+PS), AAC-LD, AAC-ELD

Optional

• Enhanced APT-X

IQOYA *LINK - IQOYA *LINK/LE

IP Audio Codec

13

FRONT AND BACK PANELS

IQOYA *LINK Front Panel

1. Headphones volume

Rotary knob allowing to adjust the volume of the headphones output

2. Headphones output

This output makes it possible to:

• A) monitor the output to be encoded

• B) monitor the analog input

• C) monitor the digital input

• D) monitor the decoded audio output

3. USB port

USB 1.1 interface: No used.

4. SDHC card

SDHC card can be used to store audio files in order to play them on the audio output when IP stream to

be decoded is lost (backup). The following file formats are supported: .mp3, .mpeg, .mpg, .wav or .mp2.

SDHC card can also be used to store the equipment configuration, or to load a configuration.

IQOYA *LINK - IQOYA *LINK/LE

Stereo IP Audio Codec

14

5. LEDs

Send

• off => TX not configured

• green => TX activated

Receive

• off => RX not configured

• green => the main audio stream is active

• lit red => no packets received

• red/green flashing + Fail-over green => Main stream lost, backup stream is decoded.

Network

• green => the interfaces configured are connected

• red => at least one of the interfaces configured is not connected

Status

• blinking green => in use

• off => configuration underway

Fail-over

• green => backup in use (main source absent)

• off => backup disabled

SD

• green => LED activated during read/write operations

IQOYA *LINK - IQOYA *LINK/LE

IP Audio Codec

15

6. LCD TFT display and keypad

This user interface allows to:

• visualize the state of the device: not active/disabled, connected in nominal configuration, connected

to a backup

• visualize ‘modulations, i.e. peak meters: RX or TX

• visualize the quality of service and band-width parameters

• Display the network configuration

• Control the settings of certain services (NTP)

• select headphones monitoring of the codec input or out put, on the analog or AES input

• reset the device to the factory settings

• update the device

• reboot the device

IQOYA *LINK - IQOYA *LINK/LE

Stereo IP Audio Codec

16

IQOYA *LINK/LE Front Panel

1. SDHC card

SDHC interface allowing providing audio files in order to play them the audio output (failover). For these

audio files, only .mp3, .mpeg, .mpg, .wav or .mp2 file formats are authorized

2. LEDs

POWER LED

Operation

Device ON, power OK

Device OFF

SEND LED

LED SEND Operation

« Send » section is not configured

Streaming is running

Streaming process failure

IQOYA *LINK - IQOYA *LINK/LE

IP Audio Codec

17

RECEIVE and FAIL-OVER LEDs

LED RECEIVE LED FAIL-OVER Prioprity 1 Priority 2

Not configured Not configured

Playing Not configured

Playing Available

Playing Missing

Failed Playing

/ flashing

Failed Not configured or

Failed

STATUS LED

LED STATUS Operation

Running

flashing

Not started

SD LED

LED SSD Operation

Default

Data transfer :

read/write operations

IQOYA *LINK - IQOYA *LINK/LE

Stereo IP Audio Codec

18

IQOYA*LINK and IQOYA *LINK/LE Back Panel

Analog audio

connectors

1

Digital audio

connectors

2

Serial

port

3

Network

connectors

4

GPIO

connectors

5

Power

supply

6

1.

Analog audio connectors

Two balanced analog mono line inputs and outputs, with software adjustable analog gain and a

maximum input level of +24 dBu on XLR-3 connectors

2. Digital audio connector

The digital audio inputs and outputs are in AES/EBU format The IQOYA is synchronized on the digital

audio input or on the internal clock of the codec. With the internal clock selected, the AES receiver uses a

sampling frequency converter of 125 dB.

Digital inputs are bypassed through relays to digital outputs during absence of power supply.

3.

Serial port

RS232 interface on DB9 (see specific appendix, management of RS232 port)

4. Network connectors

2 female Neutrik™ EtherCon™ compatible RJ45 (IP Audio, IP Backup/Control)

• 10/100 Base-T

• The first one for the main audio

• The second for control, auxiliary audio, or to connect an NAS hard drive.

5.

GPIO connectors

IQOYA *LINK: 8 General Purpose Inputs and 8 General Purpose Outputs on two female Sub-D 25

connectors

IQOYA *LINK/LE: 4 General Purpose Inputs and 4 General Purpose Outputs on two female Sub-D 25

connectors

See the chapter dedicated to the GPIOs for more details (cf. specific appendix, management of the

GPIOs).

6. Power supply

115 V - 230 VAC, 50/60 Hz

IQOYA *LINK - IQOYA *LINK/LE

IP Audio Codec

19

INSTALLATION AND CONFIGURATION

Connecting the IQOYA *LINK or IQOYA *LINK/LE

It is recommended to establish all connections before powering the device up.

Before plugging the power cord, make sure it is not damaged:

Just like for any other audio system, power the individual devices up following the audio path and power

down in the opposite direction.

Do not allow anything to rest on the power cable. Keep the power cable away from where people could trip

over it.

After switching ON the codec, it takes about 30 seconds before it is operational.

We recommend that the first connection to the IQOYA codec is done on a LAN. The default IP address of the

IQOYA codec is 192.168.0.100. Make sure all other devices connected to this LAN are in the same subnet and

have different IP addresses (this includes the PC from which you will connect to the IQOYA codec to

configure it).

To connect the IQOYA codec to the LAN, connect the Ethernet cable to the RJ45 port labeled “IP AUDIO”.

Notes: The default IP address of the “IP AUDIO” port (Eth0) is 192.168.0.100. This port is enabled by default.

The default IP address of the “IP BACKUP / CONTROL” port Eth1” is 192.168.1.100. This port is disabled by

default.

IQOYA *LINK and IQOYA *LINK/LE embed a web server that enables you to control it through your favorite

Internet browser.

WEB access rights

IQOYA *LINK and IQOYA *LINK /LE support three categories of users: Administrator, User, Read only

“Administrator” category

A user from the “Administrator” category has all the access rights on the WEB pages.

The login to the embedded WEB server as “Administrator” is:

- username: iqoya

- default password: iqoya

Password can only be modified when logged as Administrator.

“User” category

A user from the “User” category has limited access rights. “Write” access is limited to the audio parameters

(audio format, source/target IP address and UDP port).

The login to the embedded WEB server as “User” is:

- username: user

- default password: user

Password can only be modified when logged as Administrator. Old password must be entered before entering

the new one.

IQOYA *LINK - IQOYA *LINK/LE

Stereo IP Audio Codec

20

“Read-only” category

A user from the Read-only category only has “Read” access rights. He cannot modify a single parameter of the

codec.

The login to the embedded WEB server as “Read-only” is:

- username: guest

- default password: guest

Password can only be modified when logged as Administrator. Old password must be entered before entering

the new one.

Remote configuration through html pages

• Open a web browser and type in the address bar the IP address of the IQOYA codec in https mode and hit

the ‘Enter’ key.

• The WEB browser displays a message about security certificate. Select the option to continue with this WEB

server.

• Enter the username and password. For a first configuration of the codec, use the default administrator login

(username: iqoya, password: iqoya).

You can now visualize the Web pages that enable you to configure the device.

IQOYA *LINK - IQOYA *LINK/LE

IP Audio Codec

21

HTTP bandwidth limitation

In case the network bandwidth is limited and the IP audio stream takes almost all the network bandwidth, the

HTTP traffic generated when accessing the WEB pages may disturb the IP audio frames transmission on the

network, because the total bandwidth necessary for the IP audio stream plus HTTP traffic may exceed the

available network bandwidth.

To avoid this problem, IQOYA offers the possibility to set a bandwidth limitation for the HTTP traffic. This is

available from the Service menu, HTTPS.

Bandwidth limitation: default value: ‘No’.

Set this parameter to ‘Yes’ to define a bandwidth limitation for the HTTPS traffic.

Maximum bit rate (kbit/s): enter here the maximum bit rate allowed for HTTP traffic from the IQOYA to the

computer hosting the WEB browser. As a consequence, the HTTP upload traffic is also limited, and it takes

longer to display the WEB pages.

The lower the ‘Maximum bit rate’ value, the slower the WEB pages display.

Note: when loading all the WEB page (typically first access to the WEB page), there may be an additional peak

of HTTP traffic exceeding the limitation of +25%. As a consequence, it is recommended to lower the

maximum bit rate value to take into account this peak.

Example:

Network bandwidth limited to 2 Mbits/s

Audio format: PCM stereo 16 bits 48 kHz

FEC: +10%

IP audio bit rate (including FEC): 1 834 800 bits/s

Maximum value to be set for parameter ‘Maximum bit rate’: 130 kbits/s

Page is loading ...

Digigram IQOYA *LINK User manual

This manual is also suitable for

Digigram IQOYA *LINK User manual

Related papers

Other documents