NOTE:
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
PACKAGE CONTENTS
• ATake POLO Wireless Speaker
• Silicone hand loop
• USB power cable
• Instruction manual
Welcome
Thank you for your purchase of the ATake™ Wireless Speaker. You are on your way to living a life free of wires. But first, please read this user’s guide
carefully for important information concerning operation, performance and safety.
You will find the ATake™ Wireless Speaker to be convenient, compact and easy to connect with your mobile phone, iPod touch®, iPhone™, computer, mp3
player, or any other device player must be equipped with Bluetooth A2DP stereo transmitting capabilities– if not, you may need a Bluetooth Wireless
Transmitter.
Read the following recommendations before using the ATake™ Wireless Speaker. Following these you will be able to enjoy our product for many years.
Keep it dry and don’t take it to damp places to avoid the product’s internal circuit being affected.
Keep the product away from direct sunlight or hot places. High temperatures will shorten the life of electronic devices,
destroy the battery or distort certain plastic parts.
Don’t expose the product to cold areas. It may damage the internal circuit board.
Don’t try to disassemble the product as it may get damaged if you are not professional.
Don’t let it fall down onto the floor or other hard surfaces. The internal circuit might get damaged.
Don’t use intensive chemical products or detergent to clean the product.
Don’t scratch the surface with sharp things.
Please turn off the product if you don’t use it for a long time.
Care and maintenance
REV A
www.atake.com
MADE IN CHINA
TYPE: ASP-699OV
Operating Instructions
Q. Why can’t I hear sound from the speaker?
A. Check the volume level on your Bluetooth enabled music player. Also ensure that there are no ‘barriers’ between
the wireless speaker and your paired Bluetooth® device such as walls, people or furniture as this may prevent the
speaker and device from pairing successfully. If you still can not hear sound, reset the device that you are trying to
pair the speaker with. If this does not solve the issue then delete the pairing information and brign the pairing
process again.
Q. My device says ‘Bluetooth® Module not found’, what can I do?
A. This means that your device cannot find its internal Bluetooth® chip for some reason. Restarting your device
should fix this problem. If not, please contact the manufacturer of your device.
Q. My Bluetooth® device won’t pair with the speaker.
A. You need to ensure that the phone, computer or other device that you wish to connect supports the Bluetooth
A2DP stereo sound profile. The speaker will not support a mono Bluetooth® profile. Please check with your device
manufacturer to ensure compatibility.
Press once to turn ON
Press again to turn OFF
Troubleshooting
Charge Your BT Speaker
Make sure that your bluetooth speaker is fully charged before using it.
A full charge is approximately 2.5 hours and plays continuously 4 hours.
1. Connect to a USB charging cable or use USB to DC adapter to charge.
2. When the LCD light indication is Red, the device is charging.
3. The LED light indication goes off when the device is fully charged.
4. When the battery is low, the speaker turns off automatically after hearing
3 monosyllabic. Please charge your speaker immediately.
Turning your bluetooth speaker on and o
Press once to turn the device “ON”. A string of tones appear and the Blue Indicator blinks.
Press again to turn the device “OFF”. A string of tones appear and the Blue Indicator goes off.
Pairing the bluetooth speaker with your phone
1. Activate Bluetooth on the phone.
2. Turn the bluetooth speaker ON and a string of tones appear when setting to paring mode.
3. When you turn on your bluetooth speaker for the first time, the Bluetooth-enabled phone will automatically start
up in pairing mode.
(1) The Blue Indicator blinks and a string of tones appear while pairing.
(2) Search for new devices on your phone.
(3) Choose “699”.
(4) Press ’Yes’ or ‘OK’ on the phone and confirm with PIN code 0000 (4 zeros)
4. Your phone will confirm when the pairing is complete and a string of tones will appear to tell you that the
bluetooth speaker is connected.
REMARK: Every time the bluetooth speaker is turned on, it will connect to the last connected device
automatically. Remeber to turn off the device when not using it to save power.
Answering Incoming Calls
If you receive a call while listening to music on the bluetooth speaker the music will pause. After processing the
incoming call, the music will continue to play.
Indicator Denitions:
RED: Charging mode
BLUE: (quick ash) Pairing mode
BLUE: Playing mode
-
1
-
2
