ViewZ VZ-WM05 Installation guide

ViewZ
Brand
ViewZ
Model
VZ-WM05
Category
Flat panel wall mounts
Type
Installation guide

ViewZ VZ-WM05 is an LCD wall mount designed to safely and securely mount your display to a wall. It is suitable for TVs weighing up to 30kg (66lbs) and supports VESA mounting patterns of 50x50mm, 75x75mm, and 100x100mm. The mount is easy to install and comes with all necessary hardware, including screws, washers, and anchors. It features a durable steel construction and a sleek black finish that will complement any home or office décor. The ViewZ VZ-WM05 is the perfect solution for mounting your TV to the wall, freeing up valuable floor space and improving your viewing experience.

ViewZ VZ-WM05 is an LCD wall mount designed to safely and securely mount your display to a wall. It is suitable for TVs weighing up to 30kg (66lbs) and supports VESA mounting patterns of 50x50mm, 75x75mm, and 100x100mm. The mount is easy to install and comes with all necessary hardware, including screws, washers, and anchors. It features a durable steel construction and a sleek black finish that will complement any home or office décor. The ViewZ VZ-WM05 is the perfect solution for mounting your TV to the wall, freeing up valuable floor space and improving your viewing experience.

INSTALLATION MANUAL
LCD Wall Mount
LCD-201
27"
MAX
50x50
75x75
100x100
ISSUED: JUL. 2013
7
RATED
30kg
(66lbs)
RATED
Secure your display to the mount by tightening screws(just removed).
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your distributor if you have any questions.
CAU TION: DO NOT EXCEED
RATED LISTED WEIGHT. SERIOUS
INJURY OR PROPERTY DAMAGE
MAY OCCUR!
21
NOTE: Read the entire instruction manual before you start installation and assembly.
Component Checklist
WARNING
• Do not begin the installation until you have read and understood all the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone with good mechanical ability
who has basic building experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. The use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, telephone your local distributor for a replacement.
Package M
Package W
concrete anchor
W-B
(x2)ST . x5 (x )
W-A
5 5 0 2
D5 (x4)washer
M-C
M5x14 (x4)
M-B
M4x14
M-A
(x4)
4
3
2a. For Wood Stud Wall Mounting
2b. For Solid Brick and Concrete Mounting
X X
√
2
1
Drill pilot holes
Drill pilot holes
1
2
3
Screw the wall
plate onto
the wall
Screw the wall
plate onto
the wall
X X
√
WARNING
• Make sure that mounting screws are anchored into the center of the studs. The use of a stud
finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
Installers must verify that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
WARNING
ø 4mm
(ø 5/32")
55mm
(2.2")
55mm
2.2"( )
50mm
(2" )
60mm
(2.4")
60mm
2.4"( )
55mm
(2.2")
ø 8mm
(ø 5/16" )
W-A
W-B
Find and mark the
exact location of
mounting holes
Mark the exact
location of
mounting holes
W-A
1. Separating the VESA Plate
Use tool to loosen the bottom
screws in order to separate the
VESA plate from the wall mount.
XX
5
4. Installing the Display3. Installing the VESA Plate
TV
TV
TV
Tighten all screws but do not over tighten.
6
M-A
M-B
M-C
Lift the display, aligning holes in the VESA plate with the mount holes in the wall plate.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

ViewZ VZ-WM05 Installation guide

ViewZ
Brand
ViewZ
Model
VZ-WM05
Category
Flat panel wall mounts
Type
Installation guide

ViewZ VZ-WM05 is an LCD wall mount designed to safely and securely mount your display to a wall. It is suitable for TVs weighing up to 30kg (66lbs) and supports VESA mounting patterns of 50x50mm, 75x75mm, and 100x100mm. The mount is easy to install and comes with all necessary hardware, including screws, washers, and anchors. It features a durable steel construction and a sleek black finish that will complement any home or office décor. The ViewZ VZ-WM05 is the perfect solution for mounting your TV to the wall, freeing up valuable floor space and improving your viewing experience.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents